08-21-2014 03:41 PM - edited 03-11-2019 09:39 PM
Hello,
I know this has been going on for a long time, but I'm facing the traceroute issue in the ASA. Weirdly enough, I can reach the destination using traceroute with no problem, but I can't see the path to it. I pasted the result below.
I also checked my ASA configuration and the only setting that is not present is the "match any " for the "class-map class_default", because when I enter "class-map class_default" I get the following warning:
ASA(config)# class-map class-default
ERROR: % class-default is a well-known class and is not configurable under class-map
Can you guys help me? I posted below the tracert output and the concerned configuration. I can't find the misfit and I already checked most of the configuration forums.
C:\>tracert www.google.com
Tracing route to www.google.com [173.194.79.104]
over a maximum of 30 hops:
1 <1 ms <1 ms <1 ms 10.0.0.1
2 * * * Request timed out.
3 * * * Request timed out.
4 * * * Request timed out.
5 * * * Request timed out.
6 * * * Request timed out.
7 * * * Request timed out.
8 * * * Request timed out.
9 * * * Request timed out.
10 * * * Request timed out.
11 * * * Request timed out.
12 * * * Request timed out.
13 * * * Request timed out.
14 * * * Request timed out.
15 * * * Request timed out.
16 * * * Request timed out.
17 * * * Request timed out.
18 * * * Request timed out.
19 * * * Request timed out.
20 * * * Request timed out.
21 * * * Request timed out.
22 * * * Request timed out.
23 212 ms 212 ms 212 ms pb-in-f104.1e100.net [173.194.79.104]
Trace complete.
---Router configuration
icmp unreachable rate-limit 10 burst-size 5
!
!
!
object-group service ICMP_Return
service-object icmp echo-reply
service-object icmp time-exceeded
service-object icmp traceroute
service-object icmp unreachable
service-object icmp6 echo-reply
service-object icmp6 time-exceeded
service-object icmp6 unreachable
!
!
!
access-list IF_outside_access_in remark ICMP Return
access-list IF_outside_access_in extended permit object-group ICMP_Return any any
!
!
!
access-group IF_outside_access_in in interface IF_outside
!
!
!
class-map class_default
!--- This does not exit -> match any
!
!
class-map inspection_default
match default-inspection-traffic
!
!
!
policy-map global_policy
class class-default
set connection decrement-ttl
service-policy global_policy global
08-22-2014 06:29 AM
I am assuming that 10.0.0.1 is the ip address on ASA? if that is true you communication is not breaking on ASA since you see first hope in your trace route.... what is the next hop in path after ASA
10-30-2014 03:46 PM
Hello, it's not. 10.0.0.1 is my default gateway, a local router.
Something that is worth mentioning is, traceroute works for other ASA interfaces (DMZ). It only fails for the external interface.
Look:
c:\> tracert 10.0.100.50
Tracing route to webserver.corp.mycompany.com [10.0.100.50]
over a maximum of 30 hops:
1 3 ms 3 ms 2 ms 10.0.0.1
2 <1 ms <1 ms <1 ms 10.0.0.2 <- This is the ASA
3 1 ms 1 ms 1 ms webserver.corp.mycompany.com [10.0.100.50]
Trace complete.
Any ideas?
10-30-2014 08:48 PM
Hi,
Can you provide your configuration ?
Also , have you gone through this document to verify the configuration on the ASA device for the Trace route to run through the ASA device:-
http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/15246-31.html
Please let me know from where are you trying the trace route ? Is is the Internal Host ?
Thanks and Regards,
Vibhor Amrodia
10-30-2014 04:25 PM
Hi Adriano,
I think you applied the set connection decrement under the wrong class map, let's try to do it with a new one and see if it works:
class-map TRACE
match any
policy-map global_policy
class TRACE
set connection decrement-ttl
You also need to reapply the default class map under the global policy map:
policy-map global_policy
class inspection_default
Regards,
Aref
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide