cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

IOS upgrade of 7206 router

2227
Views
4
Helpful
0
Comments

 

IOS upgrade 7206 router

 

Follow the steps to upgrade IOS image of 7206 router:-

 

1 .Delete unwanted files:-

Router#Dir  disk2:

Router#Sh bootflash:

Router#delete bootflash:IOS name

Router#delete disk2:IOS name

 

Router#format bootflash:

2. Router#squeeze. If required. To remove deleted file.

 

3.To install IOS images.

Router#copy tftp: disk2: c7200p-adventerprisek9-mz.152-4.M7.bin

Router#verify /md5 disk2:c7200p-adventerprisek9-mz.152-4.M7.bin

 

O/P:-

...............................................................................................

.......................................................

verify /md5 (bootflash:c7200p-kboot-mz.152-4.M7.bin) = 18b953e28eefed3cb0d7deea4374c922

 

(verify checksum value from cisco site).It should be same.

https://software.cisco.com/download/type.html?mdfid=282188585&catid=268437899

 

https://software.cisco.com/download/release.html?mdfid=282188585&catid=268437899&softwareid=280805685&release=15.2.4S6&relind=AVAILABLE&rellifecycle=MD&reltype=latest

Hold cursor on image it will show md5 checksum value.

 

4.To install boot loader file.

Router#copy tftp: bootflash: c7200p-kboot-mz.152-4.M7.bin

Router#verify /md5 disk2: c7200p-kboot-mz.152-4.M7.bin

 

5.To install FPD image:-

Router#copy tftp: disk2: c7200p-fpd-pkg.152-4.M7.pkg

Router#verify /md5 bootflash:c7200p-kboot-mz.152-4.M7.bin

 

Verify checksum value.

 

6.Set boot loader image.

Router#Conf t

boot bootldr bootflash:c7200p-kboot-mz.152-4.M7.bin

 

 

7.Remove old IOS boot sequence:-

Router#No boot system disk2: c7200p-adventerprisek9-mz.124-15.T8.bin

 

 

Set new boot sequence:-

Router#boot system disk2: c7200p-adventerprisek9-mz.152-4.M7.bin

Router#boot system disk2: c7200p-adventerprisek9-mz.124-15.T8.bin

 

sh bootvar – Check boot variable before reload.

 

8.Reboot the router to run with new IOS installed in router.

Router#reload

 

Check after reload:-

sh version

sh bootvar – Check boot variable after reload.

 

 

Note:- VSA and NPE-G2 should be detected after IOS and FPD image upgrade.

FPD image upgrade not required if VSA card is not there.

 

Sh commands;-

Sh version

Sh inventory

Sh diag

sh hw-module all fpd

show upgrade fpd package default

 

Router#sh diag

Load for five secs: 0%/0%; one minute: 4%; five minutes: 9%

Time source is NTP, *18:44:30.133 IST Sun Dec 7 2014

 

Slot 0:

        VSA IPsec Card Port adapter

        Port adapter is analyzed

        Port adapter insertion time 00:04:27 ago

        EEPROM contents at hardware discovery:

        PCB Serial Number        : JAF1322ACKF

        Hardware Revision        : 1.0

        Part Number              : 73-10220-05

        Board Revision           : B1

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Deviation Number         : 0

        Product (FRU) Number     : C7200-VSA

        Version Identifier       : V01

        Top Assy. Part Number    : 68-2578-05

        CLEI Code                : CNUCAFNAAA

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF C1 8B 4A 41 46 31 33 32 32 41 43 4B 46 40

          0x10: 05 0D 41 01 00 82 49 27 EC 05 42 42 31 03 00 81

          0x20: 00 00 00 00 04 00 88 00 00 00 00 CB 94 43 37 32

          0x30: 30 30 2D 56 53 41 20 20 20 20 20 20 20 20 20 20

          0x40: 20 89 56 30 31 20 D9 03 C1 40 CB 87 44 0A 12 05

          0x50: C6 8A 43 4E 55 43 41 46 4E 41 41 41 FF FF FF FF

          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

 

Slot 1:

        VAM2+ Encryption/Compression engine, Port adapter

        Port adapter is analyzed

        Port adapter insertion time 00:04:28 ago

        EEPROM contents at hardware discovery:

        Hardware Revision        : 1.0

        PCB Serial Number        : JAB1203007T

        Part Number              : 73-9571-06

        Board Revision           : A0

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Deviation Number         : 0

        Product (FRU) Number     : SA-VAM2+

        Version Identifier       : V02

        Top Assy. Part Number    : 68-2288-06

        CLEI Code                : CNDQASMGAA

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF 40 04 B0 41 01 00 C1 8B 4A 41 42 31 32 30

          0x10: 33 30 30 37 54 82 49 25 63 06 42 41 30 03 00 81

          0x20: 00 00 00 00 04 00 88 00 00 00 00 CB 94 53 41 2D

          0x30: 56 41 4D 32 2B 20 20 20 20 20 20 20 20 20 20 20

          0x40: 20 89 56 30 32 20 87 44 08 F0 06 C6 8A 43 4E 44

          0x50: 51 41 53 4D 47 41 41 FF FF FF FF FF FF FF FF FF

          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

 

 

sh upgrade fpd package default

Load for five secs: 0%/0%; one minute: 2%; five minutes: 7%

Time source is NTP, *18:45:37.189 IST Sun Dec 7 2014

 

 

*************************************************************************

This IOS release requires the following default FPD Image Package for

the automatic upgrade of FPD images:

*************************************************************************

 

Version: 15.2(4)M7

 

Package Filename: c7200p-fpd-pkg.152-4.M7.pkg

 

        List of card type supported in this package:

 

                                        Minimal

                 No. Card Type          HW Ver.

                ---- ------------------ -------

                  1) VSA                  0.0

                  2) Port-Adaptor         0.0

                  3) Port-Adaptor         0.0

                  4) Port-Adaptor         0.0

                  5) Port-Adaptor         0.0

                  6) NPE-G2               0.0

                  7) C7201                0.0

                ---- ------------------ -------

 

If VSA card not detected check the physical LED status of slot0 .

a) Check logs: sh logging (IOS incompatible issue logs then check proper all image name should be same).

b) Remove card from slot by power down the router and re insert the card in slot0.

Power on the router and check LED status.

Table 1-6 VSA LED

Color

State

Function

No color

Off

Indicates that the VSA is disabled.

Green

On

Indicates the VSA is powered up and enabled for operation.

Amber

On

Indicates VSA is booting or has encountered errors.

Yellow

Powering Up

Indicates that the VSA is powering up, but software initialization has not started yet.

 

c) Issue below command and reload the router. If issue still there.

Enabling VSA card. Disable by prepending no commands.

R (config)#crypto engine slot 0

VSA will NOT come up until system power-cycle or reload...

R(config)#crypto engine accelerator 0

VSA will NOT come up until system power-cycle or reload...

R(config)#wr

R(config)#reload

 

Other O/P for information:-

 

router#copy tftp: disk2:

Address or name of remote host []? 10.2.11.194

Source filename []? c7200p-fpd-pkg.152-4.M7.pkg

Destination filename [c7200p-fpd-pkg.152-4.M7.pkg]?

Accessing tftp://10.2.11.194/c7200p-fpd-pkg.152-4.M7.pkg...

Loading c7200p-fpd-pkg.152-4.M7.pkg from 10.2.11.194 (via GigabitEthernet0/1): !!!!!!!!!!!!!!

[OK - 3450880 bytes]

 

3450880 bytes copied in 6.272 secs (550204 bytes/sec)

 

router#sh hw-module all fpd

Load for five secs: 0%/0%; one minute: 3%; five minutes: 8%

Time source is NTP, *18:44:59.061 IST Sun Dec 7 2014

 

 

==== ====================== ====== =============================================

                             H/W   Field Programmable   Current   Min. Required

Slot Card Type               Ver.  Device: "ID-Name"    Version      Version

==== ====================== ====== ================== =========== ==============

 npe NPE-G2                  1.3   1-NPEG2 I/O FPGA       0.38        0.33

---- ---------------------- ------ ------------------ ----------- --------------

   0 VSA                     0.4   1-VSA                  0.23        0.23

==== ====================== ====== =============================================

 

 

router#sh upgrade fpd package default

Load for five secs: 0%/0%; one minute: 2%; five minutes: 7%

Time source is NTP, *18:45:37.189 IST Sun Dec 7 2014

 

 

*************************************************************************

This IOS release requires the following default FPD Image Package for

the automatic upgrade of FPD images:

*************************************************************************

 

Version: 15.2(4)M7

 

Package Filename: c7200p-fpd-pkg.152-4.M7.pkg

 

        List of card type supported in this package:

 

                                        Minimal

                 No. Card Type          HW Ver.

                ---- ------------------ -------

                  1) VSA                  0.0

                  2) Port-Adaptor         0.0

                  3) Port-Adaptor         0.0

                  4) Port-Adaptor         0.0

                  5) Port-Adaptor         0.0

                  6) NPE-G2               0.0

                  7) C7201                0.

 

router#sh upgrade fpd progress

Load for five secs: 0%/0%; one minute: 3%; five minutes: 7%

Time source is NTP, *18:46:04.469 IST Sun Dec 7 2014

 

 

% There is no FPD image upgrade in progress.

 

router#sh hw-module all fpd

 

==== ====================== ====== =============================================

                             H/W   Field Programmable   Current   Min. Required

Slot Card Type               Ver.  Device: "ID-Name"    Version      Version

==== ====================== ====== ================== =========== ==============

 npe NPE-G2                  1.3   1-NPEG2 I/O FPGA       0.38        0.33

---- ---------------------- ------ ------------------ ----------- --------------

   0 VSA                     0.4   1-VSA                  0.19        0.18

==== ====================== ====== =============================================

 

example;-

Router# show hw-module all fpd

==== ====================== ====== =============================================

                             H/W   Field Programmable   Current   Min. Required

Slot Card Type               Ver.  Device: "ID-Name"    Version      Version

==== ====================== ====== ================== =========== ==============

 npe NPE-G2                  1.5   1-NPEG2 I/O FPGA       0.18         0.20 *

---- ---------------------- ------ ------------------ ----------- --------------

   0 VSA                     0.0   1-VSA                  0.10         0.10

==== ====================== ====== =============================================

 NOTES:

       - FPD images that are required to be upgraded are indicated with a '*'

         character in the "Minimal Required Version" field.

       - The following FPD image package file is required for the upgrade:

         "c7200-fpd-pkg.124-4.XD.pkg"

 

 

router#show upgrade fpd package default

*************************************************************************

This IOS release requires the following default FPD Image Package for

the automatic upgrade of FPD images:

*************************************************************************

Version: 12.4(15)T8

Package Filename: c7200p-fpd-pkg.124-15.T8.pkg

 

        List of card type supported in this package:

 

                                        Minimal

                 No. Card Type          HW Ver.

                ---- ------------------ -------

                  1) VSA                  0.0

                  2) Port-Adaptor         0.0

                  3) Port-Adaptor         0.0

                  4) Port-Adaptor         0.0

                  5) Port-Adaptor         0.0

                  6) NPE-G2               0.0

                  7) C7201                0.0

      

Useful docs:-

FPD:-

http://www.cisco.com/c/en/us/td/docs/routers/7200/configuration/feature_guides/fpd.html

 

http://www.cisco.com/c/en/us/td/docs/routers/7200/configuration/feature_guides/fpd.html

 

VSA:-

http://www.cisco.com/c/en/us/td/docs/security/vpn_modules/vam_vsa/vsa/vsa/vsa_ov.html

The Cisco 7200 series routers have three basic boot images that support different hardware options. The three images are the standard c7200-boot-mz boot image, the c7200-kboot-mz boot image, and the c7200-mboot-mz image. The c7200-kboot-mz image was released in October, 2000 and is larger than the standard c7200-boot-mz image because it supports newer hardware that is not supported in the c7200-boot-mz image. 

CreatePlease to create content
Content for Community-Ad