Hello Cisco Community,
We are experiencing an issue with our Nexus 9000 switches where we are unable to use the "event interface" command as part of Embedded Event Manager (EEM). Here are the details of our setup:
Device Details:
c1-ac5-l7# sh version
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2024, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source. This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0 or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.
Software
BIOS: version 01.09
NXOS: version 10.3(5) [Maintenance Release]
Host NXOS: version 10.3(5)
BIOS compile time: 10/08/2023
NXOS image file is: bootflash:///nxos64-cs.10.3.5.M.bin
NXOS compile time: 4/30/2024 12:00:00 [05/08/2024 09:39:13]
NXOS boot mode: LXC
Hardware
cisco Nexus9000 C93180YC-FX3 Chassis
Intel(R) Xeon(R) CPU D-1526 @ 1.80GHz with 32802764 kB of memory.
Processor Board ID FDO27131Y5L
Device name: c1-ac5-l7
bootflash: 115805708 kB
Kernel uptime is 20 day(s), 0 hour(s), 18 minute(s), 15 second(s)
Last reset at 923509 usecs after Thu Jun 27 08:36:10 2024
Reason: Reset due to upgrade
System version: 10.2(7)
Service:
plugin
Core Plugin, Ethernet Plugin
Active Package(s):
Issue Description:
According to the Cisco Documentation, the "event interface" command should be available in EEM after enabling the evmed feature.
We have already enabled the evmed feature as follows:
c1-ac5-l7# sh run | i evmed
feature evmed
However, the command is not available:
c1-ac5-l7# conf t
Enter configuration commands, one per line. End with CNTL/Z.
c1-ac5-l7(config)# event manager applet test
c1-ac5-l7(config-applet)# event ?
cli Create a cli event specification
counter Create a counter event
fanabsent Create fanabsent event specification
fanbad Create fanbad event specification
gold Create a 'Diagnostic' event specification
internal-link-flap Create a 'internal-link-flap' event specification
memory Create memory thresholds event specification
module Create a 'module' event specification
module-failure Create a 'module-failure' event specification
neighbor-discovery Show CDP new neighbors
none Manually run policy event with none
oir Create Online-Insertion-Removal event specification
policy-default Use the event in the system policy being overridden
poweroverbudget Create poweroverbudget event specification
snmp Create a 'snmp' event specification.
storm-control Create a storm control event specification
syslog Create a syslog event specification
sysmgr System manager related events
tag Event tag identifier
temperature Create temperature event specification
test Create a 'test' event specification
timer Create a timer event specification
track Create a 'track' event specification
Could someone help us understand why the "event interface" command is not available in our setup? Any guidance or suggestions would be greatly appreciated.
Thank you!
