10-19-2003 04:23 PM - edited 03-02-2019 11:06 AM
IOS C2600-ik9o3s-m 12.2(16) with 64Mb DRAM / 16Mb Flash
I've tried this card with a 12.1 Enterprise IOS and get the same error. I'm sure both the IOS's I've tried support this card.
Someone told me it's a memory partition error, but the changes I've made havn't helped.
Will provide any info you request. Greatly appreciate the help.
11-13-2016 08:36 AM
I've solved this problem.
cisco 2620 (MPC860) processor (revision 0x102) with 53248K/12288K bytes of memory.
Processor board ID JAB04170CVZ (2251918144)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
00:00:06: %PQUICC-1-UNKNOWN_WIC: PQUICC(0), WIC card has an unknown ID of 0xFF
00:00:21: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
00:00:21: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down
2. I deleted ios c2600-is-mz.122-3 and wrote c2600-ik9o3s-mz.122-8.T8.
3. After reboot in console:
cisco 2620 (MPC860) processor (revision 0x102) with 53248K/12288K bytes of memory.
Processor board ID JAB04170CVZ (2251918144)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
1 ATM network interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
SETUP: new interface ATM0/0 placed in "shutdown" state
Press RETURN to get started!
00:00:15: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
00:00:15: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down
00:00:15: %LINK-3-UPDOWN: Interface Serial0/1, changed state to down
00:00:15: %LINK-3-UPDOWN: Interface ATM0/0, changed state to down
4. Check module.
Router-1#sh diag
WIC Slot 1:
DSL SAR (ADSL)
Hardware Revision : 2.3
Part Number : 73-4771-09
Board Revision : C0
Deviation Number : 0-0
Fab Version : 05
PCB Serial Number : FOC08241F0R
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 2E 41 02 03 82 49 12 A3 09 42 43 30
0x10: 80 00 00 00 00 02 05 C1 8B 46 4F 43 30 38 32 34
0x20: 31 46 30 52 03 00 81 00 00 00 00 04 00 FF FF FF
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide