12-20-2005 09:59 PM - edited 03-03-2019 01:12 AM
Hi,
In one of cisco 6509 switch i am receving pinnacle error in almost all the modules. Not able to find any solution. Please find below the error message.
===========================================
2005 Oct 21 15:59:13 GMT +05:30 %SYS-3-SYS_LCPERR3:Module 1: Pinnacle #0, Frames
with Bad Packet CRC Error (PI_CI_S_PKTCRC_ERR - 0xC7) = 896: Module needs trou
2005 Oct 21 15:59:13 GMT +05:30 %SYS-3-SYS_LCPERR3:Module 1: Pinnacle #1, Frames
with Bad Header Checksum on DBus (PI_CI_S_HDR_FCS - 0xC5) = 63: Module needs t
2005 Oct 21 15:59:13 GMT +05:30 %SYS-3-SYS_LCPERR3:Module 1: Pinnacle #1, Frames
with Bad Packet CRC Error (PI_CI_S_PKTCRC_ERR - 0xC7) = 896: Module needs trou
2005 Oct 21 15:59:13 GMT +05:30 %SYS-3-SYS_LCPERR3:Module 2: Pinnacle #0, Frames
with Bad Header Checksum on DBus (PI_CI_S_HDR_FCS - 0xC5) = 63: Module needs t
2005 Oct 21 15:59:13 GMT +05:30 %SYS-3-SYS_LCPERR3:Module 2: Pinnacle #0, Frames
with Bad Packet CRC Error (PI_CI_S_PKTCRC_ERR - 0xC7) = 896: Module needs trou
2005 Oct 21 15:59:13 GMT +05:30 %SYS-3-SYS_LCPERR3:Module 3: Pinnacle #0, Frames
with Bad Header Checksum on DBus (PI_CI_S_HDR_FCS - 0xC5) = 63: Module needs t
2005 Oct 21 15:59:13 GMT +05:30 %SYS-3-SYS_LCPERR3:Module 3: Pinnacle #0, Frames
with Bad Packet CRC Error (PI_CI_S_PKTCRC_ERR - 0xC7) = 896: Module needs trou
2005 Oct 21 15:59:13 GMT +05:30 %SYS-3-SYS_LCPERR3:Module 7: Pinnacle #0, Frames
with Bad Header Checksum on DBus (PI_CI_S_HDR_FCS - 0xC5) = 63: Module needs t
2005 Oct 21 15:59:13 GMT +05:30 %SYS-3-SYS_LCPERR3:Module 7: Pinnacle #0, Frames
with Bad Packet CRC Error (PI_CI_S_PKTCRC_ERR - 0xC7) = 896: Module needs trou
2005 Oct 21 15:59:14 GMT +05:30 %SYS-3-SYS_LCPERR3:Module 9: Pinnacle #0, Frames
with Bad Header Checksum on DBus (PI_CI_S_HDR_FCS - 0xC5) = 63: Module needs t
2005 Oct 21 15:59:14 GMT +05:30 %SYS-3-SYS_LCPERR3:Module 9: Pinnacle #0, Frames
with Bad Packet CRC Error (PI_CI_S_PKTCRC_ERR - 0xC7) = 896: Module needs trou
===================================
I have done a supervisor engine switchover. Even after that i am receving this error message.
Please let me know the solution if anybody had solved this problem.
Krishna.
12-21-2005 12:26 AM
Hi Krishna,
Check if this can resolve the issue
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/sw_5_5/mess_rec/emsg.htm#wp1016498
Regards,
Ankur
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide