12-09-2004 04:12 AM - edited 03-02-2019 08:29 PM
Hello,
I want to get ISL trunking between a 1912-A and 3524-PWR-XL. Both switches have VLAN 1, 10 and 20. The DMZ is VLAN 10. My goal is to assign a public IP to a PC, place the port on the 3524 into VLAN 10 and have access to the internet.
- Both switches are using enterprise software.
- 3524 is vtp server
- 1912 is vtp client
#### 1912-A #######
interface FastEthernet 0/27
duplex full
!
!
vtp trunk pruning-disable 10 20
trunk Nonegotiate
Catalyst 1900 - Port B Configuration
Built-in 100Base-TX(Trunk)
----------------------- Settings ----------------------
[D] Description/name of port SW01
[S] Status of trunk Enabled
[I] Port priority (spanning tree) 128 (80 hex)
[C] Path cost (spanning tree) 10
[E] Enhanced congestion control Disabled
[F] Full duplex / Flow control Full duplex
Catalyst 1900 - Virtual LAN Configuration
----------------------- Information -------------------
VTP version: 1
Configuration revision: 4
Maximum VLANs supported locally: 1005
Number of existing VLANs: 8
Configuration last modified by: 192.168.100.2 at 03-01-1993 23:28:28
----------------------- Settings ----------------------
[N] Domain name LAN
[V] VTP mode control Client
[F] VTP pruning mode Disabled
[O] VTP traps Enabled
##### 3524-pwr-en ######
show run int fa0/24
interface FastEthernet0/24
keepalive 10
duplex full
speed 100
switchport mode trunk
end
SW01#sh int fa0/24 swi
Name: Fa0/24
Switchport: Enabled
Administrative mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: isl
Operational Trunking Encapsulation: isl
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1,2,10,20
Pruning VLANs Enabled: 2-1001
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: none
Appliance trust: none
SW01#sh vtp st
VTP Version : 2
Configuration Revision : 4
Maximum VLANs supported locally : 254
Number of existing VLANs : 8
VTP Operating Mode : Server
VTP Domain Name : LAN
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0x67 0x16 0x36 0x98 0xA8 0xE9 0xFA 0x73
Configuration last modified by 192.168.100.2 at 3-1-93 23:28:28
Thank you for your help.
12-12-2004 08:20 PM
Hello,
What debugs should I use to narrow down this problem?
What outputs should I expect to see?
Any other configs I should check?
Thank you.
12-16-2004 05:55 AM
Any suggestions or configuration I should check?
I know it has to be ISL because one of the switches is an 1900 series.
12-17-2004 06:17 AM
Few things you could check are:
Interface statistics, are there any errors.
Mac-Address tables on both devices.
Are the 1900 learning the mac-address of the DMZ
and the PC both in vlan 10 or not.
Also try placing an additional pc in vlan 10 on the 1900 and on the 3500 to verify if communication
inside the vlan works ok or not.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide