09-25-2002 01:51 AM - edited 03-02-2019 01:37 AM
I have a 3640 router acting as a remote dialin server for PC clients over two ISDN30 lines. My config is below, I am unable to dial into this router. Can anybody see a problem?
Thanks for your time !
ip address-pool local
isdn switch-type primary-net5
!
controller E1 0/0
pri-group timeslots 1-31
!
controller E1 0/1
pri-group timeslots 1-31
!
!
!
interface Loopback0
ip address 192.168.1.0 255.255.255.255
!
interface FastEthernet0/0
ip address x.x.x.x 255.255.255.252
duplex auto
speed auto
!
interface Serial0/0:15
ip address x.x.x.1 255.255.255.0
encapsulation ppp
dialer-group 1
isdn switch-type primary-net5
isdn incoming-voice modem
!
interface Serial0/1:15
ip address x.x.x.2 255.255.255.0
encapsulation ppp
dialer-group 1
isdn switch-type primary-net5
isdn incoming-voice modem
ppp authentication chap pap
!
interface Group-Async0
ip unnumbered Loopback0
encapsulation ppp
async mode interactive
peer default ip address pool dialin
ppp authentication chap dialins
group-range 33 62
!
interface Group-Async1
ip unnumbered Loopback0
encapsulation ppp
async mode interactive
peer default ip address pool dialin
ppp authentication chap dialins
group-range 65 94
!
interface Dialer0
ip unnumbered Loopback0
encapsulation ppp
no ip mroute-cache
dialer in-band
dialer-group 1
peer default ip address pool dialup
ppp authentication chap
ppp multilink
!
ip local pool dialin x.x.x.2 x.x.x.64
Daniel,
09-25-2002 11:03 AM
If these are modem users, then try adding the following:
interface Serial0/0:15
isdn incoming-voice modem
!
line 33 94
modem dialin
autoselect during-login
autoselect ppp
It looks like you can remove the config for Dialer0, it's not being used.
To troubleshoot, try each of these steps in order
- debug isdn q931 - make sure the calls arrive and are answered
- debug modem - make sure the modems train up and answer
- debug ppp neg - make sure that PPP negotiates and an address is assigned
09-26-2002 06:13 AM
No joy,
Do the serial interfaces look correctly configured to you?
Daniel,
09-26-2002 09:47 AM
You've never specified if these are async or ISDN users dialing in. If they are async, the only command you need under the serial interfaces is "isdn incoming-voice modem". For sync ISDN users, the configs look fine except that Serial0/0:15 should have PPP authentication enabled.
Again, if you are having problems still you should enable the debugs to see what is going on.
10-07-2002 01:09 AM
Hi,
In the D-channel configuration of your PRI port (Ser0/0:15 and ser0/1:15)
IP processing should not be used.
As Joy said, the modem/line configuration need to be done to allow dialin access.(If you have installed the MICA bank in slot 1 .. line 32-64, slot 1 65-96)
line 32 62
modem DialIn
the following config should work fine for dial in access of Async/ ISDN
interface serial0/0:15
no ip address
encapsulation ppp
dialer-group 1
isdn incoming-voice modem
interface serial0/1:15
no ip address
encapsulation ppp
dialer-group 1
isdn incoming-voice modem
interface Group-Async0
ppp authentication chap pap dialin
group-range 33 62
interface Group-Async1
ppp authentication chap pap dialin
group-range 65 94
line 33 62
autoselect ppp
autoselect during-login
login authentication dialin
modem DialIn
line 65 94
autoselect ppp
autoselect during-login
login authentication dialin
modem DialIn
thanks
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide