I am in Seoul(router B), remote office is in China.
Remote router(router A) is Cisco 2610, WIC-1T, VIC-2FXO, 128Kbps internet Leased line, Serial interface IP use unnumberd ethernet 0, ethernet 0 ip is same as following "show run ".
In the Seoul , ping to router then "time out"(also telnet) but,
ping to Server in the router A's ethernet network then icmp "OK".
So, After router A's reloading, ping to router then icmp "OK" in about 20~30 Minutes, ping is "time out".
But Server is always icmp "OK".....What happen?
I can mail to you who want it, "show tech"
"show run" & "show version" for reference,,,,,,(IP Address is false for security)
Building configuration...
Current configuration:
!
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname XXX
!
enable secret 5 <removed>
!
!
!
!
!
memory-size iomem 10
ip subnet-zero
ip cef
no ip finger
ip name-server 202.96.128.68
ip name-server 202.96.134.133
!
!
!
!
voice-port 1/0/0
cptone CN
description "Connect to 254
!
voice-port 1/0/1
cptone CN
description "Connect to 255
!
dial-peer voice 1 pots
destination-pattern 254
port 1/0/0
!
dial-peer voice 2 pots
destination-pattern 255
port 1/0/1
!
dial-peer voice 3 voip
destination-pattern 201
ip precedence 5
session target ipv4:210.222.83.100
!
dial-peer voice 4 voip
destination-pattern 202
ip precedence 5
session target ipv4:210.222.83.100
!
dial-peer voice 5 voip
destination-pattern 203
ip precedence 5
session target ipv4:210.222.83.100
!
dial-peer voice 6 voip
destination-pattern 204
fax-rate 14400
ip precedence 5
session target ipv4:210.222.83.100
!
process-max-time 200
!
interface Ethernet0/0
ip address 192.168.0.254 255.255.255.0 secondary
ip address 61.142.108.65 255.255.255.240
no ip directed-broadcast
ip nat inside
no ip mroute-cache
no keepalive
!
interface Serial0/0
ip unnumbered Ethernet0/0
no ip directed-broadcast
ip nat outside
no ip route-cache cef
no ip mroute-cache
no fair-queue
!
ip nat pool NAT 61.142.108.65 61.142.108.65 netmask 255.255.255.240
ip nat inside source list 1 pool NAT overload
ip classless
ip route 0.0.0.0 0.0.0.0 Serial0/0
no ip http server
!
logging 218.18.52.34
access-list 1 permit 192.168.0.0 0.0.0.255
snmp-server engineID local 000000090200003094364360
snmp-server community <removed> RO
!
line con 0
password 7 <removed>
login
transport input none
line aux 0
line vty 0 4
password 7 <removed>
login
!
!
no scheduler allocate
end
------------------ show version ------------------
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IS-M), Version 12.0(5)T1, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Tue 17-Aug-99 14:39 by cmong
Image text-base: 0x80008088, data-base: 0x80B5E15C
ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
daejin uptime is 4 minutes
System returned to ROM by power-on
System image file is "flash:c2600-is-mz_120-5_T1.bin"
cisco 2610 (MPC860) processor (revision 0x203) with 22528K/2048K bytes of memory.
Processor board ID JAD034299PJ (2575152651)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
2 Voice FXO interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
