cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
402
Views
0
Helpful
3
Replies

Routing and Traceroute problems

andrewpartington
Beginner
Beginner

Hi..

I have a strange problem with a very simple network that has stumped me and hoping someone can shed some light. Probably a brain fade, but got me beat

Brief description

2 x 1720 routers connected via a frame.

Router A config :

F/E 0 = 192.0.0.1/24

Serial 0 = 192.168.200.2/30

F/E 0 connected to Cisco 2924 switch

Router A default gateway = 192.168.200.1

Router has RIP version 2 enabled with networks 192.0.0.0 and 192.168.200.0 being broadcast.

Router B config:-

F/E 0 = 192.168.1.1/24

Serial 0 = 192.168.200.1/30

F/E 0 connected to hub

Router default gateway = 192.168.200.2

Router has RIP version 2 enabled with networks 192.168.1.0 and 192.168.200.0 being broadcast.

Switch Config (located behind router A):-

Switch has IP address = 192.0.0.141

Switch default gateway = 192.168.200.2

Router A (via switch) workstation(s) config:-

default gateway = 192.0.0.141 (to the switch)

Router B workstation config:-

Default gateways set to 192.168.1.1 (have tried 192.168.200.1 as well)

OK (apologies for the lengthy detail)

From Router B I can ping router A and workstations beyond Router A

From Router B I can traceroute to workstations behind router A and the switch, which is good. To my thinking there is a route to and from Router B through Router A, through the switch, to the workstation and then back again.

Problem is from Router A..(and anything behind router A)

I can ping workstations beyond Router B (via the hub), but I cannot traceroute to any devices behind Router B.

Im struggling to see what the reason is. I understand ping is different to traceroute, but I can FTP to the devices I am trying to traceroute to..weird...

Its causing some problems with an application we are running where comms are OK between Router B to A...but fail from Router A to B ( well, the devices behind router B ).

I can traceroute to each one of the routers..the problems happen when I try to get to devices beyond router B.

Confused!!?? I am just reading this, but hopefully someone will be able to help.

BTW, the workstations in question (behind router B) are running DOS and TCP/IP (PCTCP)

Any ideas folks???

Really appreciate any assistance...

Andrew

3 Replies 3

sbrobak
Beginner
Beginner

Your pcs and switch should have the def. gw of their local router. Switch and pc's at site A should have 192.0.0.1 as their gw. At B the gw should be 192.168.1.1.

aaeran
Beginner
Beginner

Hi Andrew,

U seems to be messed up in ur problem. Well..i m trying my hand in it...since i m a novice worker on routers and just got CCNA certified...cant say that my solution will really work for u...but still trying my hand to help u out.

Well...first of all....do write "no auto-summary" command in config mode in both the routers. Then, check out the address of F/E port in Router A. I think...its not the right address to be mentioned...please check it out.

Hope this helps u...

Best of luck to u & me too...since this is the first time I m trying my hand

Goodluck

Ankur

andrewpartington
Beginner
Beginner

AHhh..

I think the switches default gateway is set wrong. SHould be 192.0.0.1 and not 192.168.200. whatever.....

I`ll give this a whirl and see how it goes.

Strange though that if I can trace from one system to the other, but not the other way around. Surely if theres a path to and a return path from the device, then it works both ways...

Thanks very much guys...I`ll see how it goes

Andrew

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers