Hello all
I'm having issues recovering a 4948E while trying to install the latest image, I found several references to rommon recovery but nothing specific to an instance where you have a scenario where during a file transfer a partial image was left as "invalid" see below - When doing a show bootflash before the initial reload after changing my boot option I did not see the "invalid" file, but now it shows in the bootflash.
I tried a boot bootflash:cat4500-entservicesk9-mz.150-2.SG9.bin, but I still can't get it to boot the new image,
Can this be caused by the "invalid" partial image?
Thanks in advance
rommon 3 >dir bootflash:
File size Checksum File name
--------------------------------------------------
19475680 bytes (0x1292ce0) 0x639e3fdc cat4500-entservicesk9-mz.150-2.SG9.bin
12402804 bytes (0xbd4074) 0xb4ecf112 cat4000-i9s-mz.122-25.EWA10.bin(deleted)
8716288 bytes (0x850000) 0x4761036e cat4500-entservicesk9-mz.150-2.SG9.bin(invalid)
Total space = 61341696 bytes, Available = 20746540 bytes
-------------------------------------------------------------------------------------------------------------------------------
rommon 18 >boot bootflash:cat4500-entservicesk9-mz.150-2.SG9.bin
Rommon reg: 0x00004180
############
Decompression done, relocating ...
k2diags version 5.7
prod: WS-C4948-10GE part: 73-9344-09 serial: FOX112603KG
Power-on-self-test for Module 1: WS-C4948-10GE
Port/Test Status: (. = Pass, F = Fail, U = Untested)
Cpu Subsystem Tests ...
seeprom: . temperature_sensor: .
Port Traffic: L2 Serdes Loopback ...
0: . 1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: . 9: . 10: . 11: .
12: . 13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: .
24: . 25: . 26: . 27: . 28: . 29: . 30: . 31: . 32: . 33: . 34: . 35: .
36: . 37: . 38: . 39: . 40: . 41: . 42: . 43: . 44: . 45: . 46: . 47: .
62: . 63: .
Port Traffic: L2 Asic Loopback ...
UNHANDLED ROMMON EXCEPTION at PC=0453ab5c
Vector=00000100 MSR=02029230 LR=0453ab24
MCSR=00000000
CISR0=00000000 CISR1=40000000
DDR_ERR_DETECT=00000000
**********************************************************
* *
* Welcome to Rom Monitor for WS-C4948-10GE System. *
* Copyright (c) 2003-2006 by Cisco Systems, Inc. *
* All rights reserved. *
* *
**********************************************************
Rom Monitor Program Version 12.2(31r)SGA
Supervisor: WS-C4948-10GE Chassis: WS-C4948
Hardware Revisions - Board: 8.5 CPLD Gill: 20
MAC Address : 00-1d-45-0d-81-7f
Ip Address : Not set.
Netmask : Not set.
Gateway : Not set.
TftpServer : Not set.
***** The system will autoboot in 5 seconds *****
Type control-C to prevent autobooting.
. . . .
Autoboot cancelled......... please wait!!
-----------------------------------------------------------------------------------------------------------------------
rommon 1 >set
PS1=rommon ! >
ConfigReg=0x0102
RommonVer=12.2(31r)SGA
BootedFileName=bootflash:cat4500-entservicesk9-mz.150-2.SG9.bin
rommon 2 >
------------------------------------------------------------------------------------------------------------------------
rommon 2 >version
Rom Monitor Program Version 12.2(31r)SGA
Compiled Tue 22-Aug-06 14:08 by khalidm-122_31r_SGA
Supervisor: WS-C4948-10GE Chassis: WS-C4948
Hardware Revisions - Board: 8.5 CPLD Gill: 20
Installed memory: 256 MBytes
