Clock Rate on Serial Interfaces

[wkrawiec]

Is there any command that shows me the clockrate/Speed of my Leased Line.

A "Show Controllers S0" for example just shows me that there is RX and TX

Clock detected, but not the Clockrate.

Regards

Werner

[y.ujjainwala]

this output was taken from a 3660 router.

Router#sh controllers serial 1/0

M4T: show controller:

PAS unit 0, subunit 0, f/w version 1-45, rev ID 0x2800001, version 3

idb = 0x60D81210, ds = 0x60D82D00, ssb=0x60D82FD8

Clock mux=0x0, ucmd_ctrl=0x1C, port_status=0x74

Serial config=0x8, line config=0x200

maxdgram=1608, bufpool=48Kb, 31 particles

DCD=up DSR=up DTR=up RTS=up CTS=up

line state: up

cable type : V.35 DTE cable, received clockrate 2047212

base0 registers=0x3D000000, base1 registers=0x3D002000

mxt_ds=0x610472E0, rx ring entries=40, tx ring entries=128

rxring=0x38E72C0, rxr shadow=0x60D878CC, rx_head=19

txring=0x38E7440, txr shadow=0x60D87AD8, tx_head=2, tx_tail=2, tx_count=0

throttled=0, enabled=0

rx_no_eop_err=56, rx_no_stp_err=0, rx_no_eop_stp_err=0

rx_no_buf=0, rx_soft_overrun_err=0, dump_err= 3558, bogus=0, mxt_flags=0x20

tx_underrun_err=0, tx_soft_underrun_err=0, tx_limited=1(2)

tx_fullring=2282074, tx_started=13048593

it shows the clockrate detected from the serial input.

regards

Ajay.

[wkrawiec]

ROU04MAN#sh controllers s0/1

Interface Serial0/1

Hardware is Quicc 68360

DTE V.11 (X.21) TX and RX clocks detected.

idb at 0x6100C6B8, driver data structure at 0x61011BBC

WIC interrupt reg = F

SCC Registers:

General [GSMR]=0x2:0x00000030, Protocol-specific [PSMR]=0x8

Events [SCCE]=0x0000, Mask [SCCM]=0x001F, Status [SCCS]=0x0006

Transmit on Demand [TODR]=0x0, Data Sync [DSR]=0x7E7E

Interrupt Registers:

Config [CICR]=0x00C9CF00, Pending [CIPR]=0x00000000

Mask [CIMR]=0xE0004400, In-srv [CISR]=0x00000000

SDMA Registers:

[SDSR]=0x00, [SDAR]=0x01800228, [SDCR]=0x0772

Command register [CR]=0x640

Port A [PADIR]=0x0100, [PAPAR]=0xFFFF

[PAODR]=0x0000, [PADAT]=0xFEFF

Port B [PBDIR]=0x0013FE, [PBPAR]=0x00000E

[PBODR]=0x000000, [PBDAT]=0x03CC5D

Port C [PCDIR]=0x0002, [PCPAR]=0x000C

[PCSO]=0x00E0, [PCDAT]=0x0F3D, [PCINT]=0x0001

Receive Ring

rmd(3C010490): status 9000 length 8B address 1922E24

rmd(3C010498): status 9000 length 86 address 19200A4

rmd(3C0104A0): status 9000 length 86 address 1920DA4

rmd(3C0104A8): status 9000 length 2E address 1921AA4

rmd(3C0104B0): status 9000 length 42 address 1922124

rmd(3C0104B8): status 9000 length 86 address 19234A4

rmd(3C0104C0): status B000 length 89 address 19227A4

Transmit Ring

tmd(3C0104C8): status 5C00 length 95 address 1949FEA

tmd(3C0104D0): status 5C00 length 95 address 1936DEA

tmd(3C0104D8): status 5C00 length 11F address 19E3954

tmd(3C0104E0): status 5C00 length 18 address 1800214

tmd(3C0104E8): status 5C00 length B5 address 194866A

tmd(3C0104F0): status 5C00 length D3 address 193E0AA

tmd(3C0104F8): status 7C00 length 95 address 19459CA

SCC GENERAL PARAMETER RAM (at 0x3C010D00)

Rx BD Base [RBASE]=0x490, Fn Code [RFCR]=0x19

Tx BD Base [TBASE]=0x4C8, Fn Code [TFCR]=0x19

Max Rx Buff Len [MRBLR]=1548

Rx State [RSTATE]=0x19008240, BD Ptr [RBPTR]=0x4B8

Tx State [TSTATE]=0x19000348, BD Ptr [TBPTR]=0x4E8

SCC HDLC PARAMETER RAM (at 0x3C010D38)

CRC Preset [C_PRES]=0xFFFF, Mask [C_MASK]=0xF0B8

Errors: CRC [CRCEC]=66, Aborts [ABTSC]=41, Discards [DISFC]=0

Nonmatch Addr Cntr [NMARC]=0

Retry Count [RETRC]=0

Max Frame Length [MFLR]=1608

Rx Int Threshold [RFTHR]=0, Frame Cnt [RFCNT]=50816

User-defined Address 0000/0000/0000/0000

User-defined Address Mask 0x0000

buffer size 1524

QUICC SCC specific errors:

12744 input aborts on receiving flag sequence

0 throttles, 0 enables

0 overruns

0 transmitter underruns

0 transmitter CTS losts

197012 aborted short frames

this is what I get on a 3620 with X.21 Cable