Cannot get ip address from dhcp

[wfqk]

Hello,

Client cannot get ip address. The dhcp debug is as below. Anyone can help to give some suggestions? Diagram is like this:

 SW1(dhcp) -----SW2----PC

SW1:

*Mar 19 22:47:23.288: Option 82 not present
*Mar 19 22:47:23.288: DHCPD: Reload workspace interface Vlan40 tableid 0.
*Mar 19 22:47:23.288: DHCPD: tableid for 10.1.218.1 on Vlan40 is 0
*Mar 19 22:47:23.288: DHCPD: client's VPN is .
*Mar 19 22:47:23.288: DHCPD: No option 125
*Mar 19 22:47:23.288: DHCPD: DHCPREQUEST received from client 0140.665c.7116.9e.
*Mar 19 22:47:23.288: DHCPD: DHCPREQUEST received on interface Vlan40.
*Mar 19 22:47:23.288: DHCPD: FSM state change INVALID
*Mar 19 22:47:23.288: DHCPD: Workspace state changed from INIT to INVALID
*Mar 19 22:47:23.288: DHCPD: Client either rebooted or rebinding we are seeing the client for first time
*Mar 19 22:47:23.288: DHCPD: excluded address: 10.1.218.126
*Mar 19 22:47:23.288: DHCPD: Finding a relay for client 0140.665c.7116.9e on interface Vlan40.
*Mar 19 22:47:23.288: DHCPD : Locating relay for Subnet 10.1.218.1
*Mar 19 22:47:23.289: DHCPD: Looking up binding using address 10.1.218.1
*Mar 19 22:47:23.289: DHCPD: setting giaddr to 10.1.218.1.
*Mar 19 22:47:23.289: DHCPD: BOOTREQUEST from 0140.665c.7116.9e forwarded to 10.1.218.6.
*Mar 19 22:47:23.289: DHCPD: BOOTREQUEST from 0140.665c.7116.9e forwarded to 10.1.218.5.
*Mar 19 22:47:23.290: Option 82 not present
*Mar 19 22:47:23.290: DHCPD: Reload workspace interface Vlan40 tableid 0.
*Mar 19 22:47:23.290: DHCPD: tableid for 10.1.218.1 on Vlan40 is 0
*Mar 19 22:47:23.290: DHCPD: client's VPN is .
*Mar 19 22:47:23.291: DHCPD: No option 125
*Mar 19 22:47:23.291: DHCPD: forwarding BOOTREPLY to client 408d.6671.169e.
*Mar 19 22:47:23.291: DHCPD: Forwarding reply on numbered intf
*Mar 19 22:47:23.291: DHCPD: Option 125 not present in the msg.
*Mar 19 22:47:23.291: DHCPD: Clearing unwanted ARP entries for multiple helpers
*Mar 19 22:47:23.291: DHCPD: src nbma addr as zero
*Mar 19 22:47:23.291: DHCPD: ARP entry exists (10.1.218.126, 408d.6611.169e).
*Mar 19 22:47:23.291: DHCPD: egress Interfce Vlan40

[Georg Pauwen]

Hello,

post the full running configurations of both switches, and indicate which access port on SW2 is connected to the PC...

[paul driver]

Hello
Remove any helper addressing off the switches, Make sure vlan 40 is also created on the switches and the end host is connected to a switchport that assigned to vlan 40

[wfqk]

Thank you two very much for your reply. I would love to tell you more info or full configuration. but the post is open to public.. I only can answer specific question if you have it. One of my question is if the dhcp option82 is required in this case based on the debug?

[paul driver]

Hello

Post the run configurations but hide the addressing, this way we can see if anything is a miss?