Buy or Renew
Buy or Renew
cancel
Turn on suggestions
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Bookmark
|
Subscribe
|
1170
Views
0
Helpful
1
Replies

Cisco 2800 and Zebra on FreeBSD OSPF problems

jasonatcco
Level 1
Level 1

‎01-17-2008 12:30 PM - edited ‎03-03-2019 08:18 PM

CiCisco router on one side, Zebra running ospfd on freebsd 6.2 on the other, Ethernet interfaces. First 30 seconds all is good, then everything stops for a split second and it's good again, this repeats continuously. I see this on the Cisco side but can't really find the problem. I suspect it has something to do with the 6th line, Cannot see ourself in hello but

Jan 17 15:10:12.673: OSPF: Rcv hello from 10.111.8.27 area 2 from GigabitEthernet0/0.991 10.111.8.27

Jan 17 15:10:12.673: OSPF: End of hello processing

Jan 17 15:10:12.705: OSPF: rcv. v:2 t:1 l:44 rid:10.111.2.100

aid:0.0.0.2 chk:E4F6 aut:0 auk: from GigabitEthernet0/0.201

Jan 17 15:10:12.705: OSPF: Rcv hello from 10.111.2.100 area 2 from GigabitEthernet0/0.201 10.111.2.100

Jan 17 15:10:12.705: OSPF: Cannot see ourself in hello from 10.111.2.100 on GigabitEthernet0/0.201, state INIT

Jan 17 15:10:12.705: OSPF: Neighbor change Event on interface GigabitEthernet0/0.201

Jan 17 15:10:12.705: OSPF: DR/BDR election on GigabitEthernet0/0.201

Jan 17 15:10:12.705: OSPF: Elect BDR 10.111.0.1

Jan 17 15:10:12.705: OSPF: Elect DR 10.111.0.1

Jan 17 15:10:12.705: OSPF: Elect BDR 0.0.0.0

Jan 17 15:10:12.705: OSPF: Elect DR 10.111.0.1

Jan 17 15:10:12.705: DR: 10.111.0.1 (Id) BDR: none

Jan 17 15:10:12.705: OSPF: Reset GigabitEthernet0/0.201 flush timer

Jan 17 15:10:12.705: OSPF: Remember old DR 10.111.2.100 (id)

Jan 17 15:10:12.705: OSPF: Send immediate hello to nbr 10.111.2.100, src address 10.111.2.100, on GigabitEthernet0/0.201

Jan 17 15:10:12.705: OSPF: Send hello to 10.111.2.100 area 2 on GigabitEthernet0/0.201 from 10.111.2.1

Jan 17 15:10:12.705: OSPF: End of hello processing

Jan 17 15:10:12.721: OSPF: rcv. v:2 t:2 l:32 rid:10.111.2.100

aid:0.0.0.2 chk:ED73 aut:0 auk: from GigabitEthernet0/0.201

Jan 17 15:10:12.721: OSPF: Rcv DBD from 10.111.2.100 on GigabitEthernet0/0.201 seq 0x478FB622 opt 0x0 flag 0x7 len 32 mtu 1500 state INIT

Jan 17 15:10:12.721: OSPF: 2 Way Communication to 10.111.2.100 on GigabitEthernet0/0.201, state 2WAY

Jan 17 15:10:12.721: OSPF: Neighbor change Event on interface GigabitEthernet0/0.201

Jan 17 15:10:12.721: OSPF: DR/BDR election on GigabitEthernet0/0.201

Jan 17 15:10:12.721: OSPF: Elect BDR 10.111.2.100

Jan 17 15:10:12.721: OSPF: Elect DR 10.111.0.1

Jan 17 15:10:12.721: DR: 10.111.0.1 (Id) BDR: 10.111.2.100 (Id)

Jan 17 15:10:12.721: OSPF: Send DBD to 10.111.2.100 on GigabitEthernet0/0.201 seq 0x21B2 opt 0x40 flag 0x7 len 32

Jan 17 15:10:12.721: OSPF: NBR Negotiation Done. We are the SLAVE

Jan 17 15:10:12.721: OSPF: Send DBD to 10.111.2.100 on GigabitEthernet0/0.201 seq 0x478FB622 opt 0x40 flag 0x2 len 732

10.111.0.2

aid:0.0.0.2 chk:92E aut:0 auk: from GigabitEthernet0/0.240

Jan 17 15:10:13.785: OSPF: rcv. v:2 t:4 l:64 rid:10.111.0.2

aid:0.0.0.2 chk:92E aut:0 auk: from GigabitEthernet0/0.921

Jan 17 15:10:13.785: OSPF: rcv. v:2 t:4 l:64 rid:10.111.8.107

aid:0.0.0.2 chk:C5 aut:0 auk: from GigabitEthernet0/0.807

Jan 17 15:10:13.785: OSPF: rcv. v:2 t:4 l:64 rid:10.111.8.59

aid:0.0.0.2 chk:F5 aut:0 auk: from GigabitEthernet0/0.85

Jan 17 15:10:13.785: OSPF: rcv. v:2 t:4 l:64 rid:10.111.8.35

aid:0.0.0.2 chk:10D aut:0 auk: from GigabitEthernet0/0.83

...

Labels:
0 Helpful
1 Reply 1

jasonatcco
Level 1
Level 1

‎01-17-2008 12:33 PM

Jan 17 15:10:12.961: OSPF: rcv. v:2 t:2 l:712 rid:10.111.2.100

aid:0.0.0.2 chk:8342 aut:0 auk: from GigabitEthernet0/0.201

Jan 17 15:10:12.961: OSPF: Rcv DBD from 10.111.2.100 on GigabitEthernet0/0.201 seq 0x478FB623 opt 0x0 flag 0x3 len 712 mtu 1500 state EXCHANGE

Jan 17 15:10:12.961: OSPF: Send DBD to 10.111.2.100 on GigabitEthernet0/0.201 seq 0x478FB623 opt 0x40 flag 0x0 len 32

Jan 17 15:10:12.965: OSPF: rcv. v:2 t:1 l:52 rid:10.111.8.19

aid:0.0.0.2 chk:A136 aut:0 auk: from GigabitEthernet0/0.405

Jan 17 15:10:12.965: OSPF: Rcv hello from 10.111.8.19 area 2 from GigabitEthernet0/0.405 10.111.8.19

Jan 17 15:10:12.965: OSPF: End of hello processing

Jan 17 15:10:12.965: OSPF: rcv. v:2 t:1 l:56 rid:10.111.0.18

aid:0.0.0.0 chk:0 aut:2 keyid:1 seq:0x3DFF49E8 from GigabitEthernet0/1.297

Jan 17 15:10:12.965: OSPF: Rcv hello from 10.111.0.18 area 0 from GigabitEthernet0/1.297 10.111.0.18

Jan 17 15:10:12.965: OSPF: End of hello processing

Jan 17 15:10:12.965: OSPF: rcv. v:2 t:2 l:32 rid:10.111.2.100

aid:0.0.0.2 chk:ED77 aut:0 auk: from GigabitEthernet0/0.201

Jan 17 15:10:12.965: OSPF: Rcv DBD from 10.111.2.100 on GigabitEthernet0/0.201 seq 0x478FB624 opt 0x0 flag 0x1 len 32 mtu 1500 state EXCHANGE

Jan 17 15:10:12.965: OSPF: Exchange Done with 10.111.2.100 on GigabitEthernet0/0.201

Jan 17 15:10:12.965: OSPF: Send LS REQ to 10.111.2.100 length 12 LSA count 1

Jan 17 15:10:12.965: OSPF: Send DBD to 10.111.2.100 on GigabitEthernet0/0.201 seq 0x478FB624 opt 0x40 flag 0x0 len 32

Jan 17 15:10:13.761: OSPF: rcv. v:2 t:4 l:64 rid:10.111.2.100

aid:0.0.0.2 chk:6CE aut:0 auk: from GigabitEthernet0/0.201

Jan 17 15:10:13.761: OSPF: rcv. v:2 t:4 l:60 rid:10.111.2.100

aid:0.0.0.2 chk:9247 aut:0 auk: from GigabitEthernet0/0.201

Jan 17 15:10:13.761: OSPF: Rcv LS UPD from 10.111.2.100 on GigabitEthernet0/0.201 length 64 LSA count 1

Jan 17 15:10:13.765: OSPF: Synchronized with 10.111.2.100 on GigabitEthernet0/0.201, state FULL

Jan 17 15:10:13.765: %OSPF-5-ADJCHG: Process 1, Nbr 10.111.2.100 on GigabitEthernet0/0.201 from LOADING to FULL, Loading Done

Jan 17 15:10:13.765: OSPF: Rcv LS UPD from 10.111.2.100 on GigabitEthernet0/0.201 length 60 LSA count 1

Jan 17 15:10:13.765: OSPF: Include link to old DR on GigabitEthernet0/0.201

Jan 17 15:10:13.765: OSPF: Build router LSA for area 2, router ID 10.111.0.1, seq 0x800006C5

Jan 17 15:10:13.765: OSPF: Build network LSA for GigabitEthernet0/0.201, router ID 10.111.0.1

Jan 17 15:10:13.765: OSPF: Build network LSA for GigabitEthernet0/0.201, router ID 10.111.0.1

Jan 17 15:10:13.785: OSPF: rcv. v:2 t:1 l:52 rid:10.111.8.75

aid:0.0.0.2 chk:A08E aut:0 auk: from GigabitEthernet0/0.936

Jan 17 15:10:13.785: OSPF: Rcv hello from 10.111.8.75 area 2 from GigabitEthernet0/0.936 10.111.8.75

Jan 17 15:10:13.785: OSPF: End of hello processing

Jan 17 15:10:13.785: OSPF: rcv. v:2 t:1 l:52 rid:10.111.8.99

aid:0.0.0.2 chk:A048 aut:0 auk: from GigabitEthernet0/0.933

Jan 17 15:10:13.785: OSPF: Rcv hello from 10.111.8.99 area 2 from GigabitEthernet0/0.933 10.111.8.99

Jan 17 15:10:13.785: OSPF: End of hello processing

Jan 17 15:10:13.785: OSPF: rcv. v:2 t:1 l:48 rid:10.111.2.100

aid:0.0.0.2 chk:DA82 aut:0 auk: from GigabitEthernet0/0.201

Jan 17 15:10:13.785: OSPF: Rcv hello from 10.111.2.100 area 2 from GigabitEthernet0/0.201 10.111.2.100

Jan 17 15:10:13.785: OSPF: Neighbor change Event on interface GigabitEthernet0/0.201

Jan 17 15:10:13.785: OSPF: DR/BDR election on GigabitEthernet0/0.201

Jan 17 15:10:13.785: OSPF: Elect BDR 0.0.0.0

Jan 17 15:10:13.785: OSPF: Elect DR 10.111.2.100

Jan 17 15:10:13.785: OSPF: Elect BDR 10.111.0.1

Jan 17 15:10:13.785: OSPF: Elect DR 10.111.2.100

Jan 17 15:10:13.785: DR: 10.111.2.100 (Id) BDR: 10.111.0.1 (Id)

Jan 17 15:10:13.785: OSPF: Set GigabitEthernet0/0.201 flush timer

Jan 17 15:10:13.785: OSPF: Remember old DR 10.111.0.1 (id)

Jan 17 15:10:13.785: OSPF: End of hello processing

0 Helpful
Top