Cisco 2811 Stuck in readonly rommon mode - Page 2

hill.tyrone@outlook.com · ‎11-30-2017

I have a 2811 router and I can not get it to boot properly. I've been troubleshooting it for a few days now but haven't made any progress. I'll start with with I've tried so far and post the output from the commands I have tried.

The router was pulled off our rack after we upgraded to a new router. It has a Cisco 128Mb CF card. When I first booted, it went directly into rommon mode. The first thing I tried was the confreg 0x2142 command. After I power cycle the router it just boots back to the same prompt. I setup a TFTP server and tried copying the IOS but kept getting timeout errors. I tried different ethernet cables and both ports ethernet port on the router but no luck. I then tried the xmodem method and changed the serial baud rate 1152000. I left it running overnight and came back to a timeout error. I then found a spare 256MB Sandisk Compact Flash card and tried the TFTP and xmodem methods again but got the same error. I then bought a compact flash card reader and was able to read and format both cards. I copied the contents of the original CF card to my PC then formatted (tried both FAT and FAT32) and put a new IOS on it but it still would not boot. I then put the original files on the SanDisk CF card (tried both FAT and FAT32 again) but still get the same errors. I then found an old 4GB usb memory stick and formatted it then copied a new IOS to it but I can't seem to access the drive using the DIR command. I just ordered a new OEM Cisco 128MB CF card but it probably will not be here till next week. Any information or suggestions would be helpful. Below is the output from the console.

___________________________________________________________________________

System Bootstrap, Version 12.4(13r)T11, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2009 by cisco Systems, Inc.

Initializing memory for ECC
..
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
open(): Open Error = -66
boot: cannot open "flash:"
boot: cannot determine first executable file name on device "flash:"
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
Entering rommon> prompt after several failed attempts to boot an IOS image.
Please check your internal/external flash drives for the correct IOS image
and issue 'reset' at the rommon> prompt to re-try the boot process.
rommon 1 > confreg 0x2142

You must reset or power cycle for new config to take effect
rommon 2 >

System Bootstrap, Version 12.4(13r)T11, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2009 by cisco Systems, Inc.

Initializing memory for ECC
..
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
open(): Open Error = -66
boot: cannot open "flash:"
boot: cannot determine first executable file name on device "flash:"
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
Entering rommon> prompt after several failed attempts to boot an IOS image.
Please check your internal/external flash drives for the correct IOS image
and issue 'reset' at the rommon> prompt to re-try the boot process.
rommon 1 > dev
Devices in device table:
id name
flash: compact flash
bootflash: boot flash
usbflash0: usbflash0
usbflash1: usbflash1
eprom: eprom
rommon 2 > dir flash:
program load complete, entry point: 0x8000f000, size: 0xcb80
open(): Open Error = -66
dir: cannot open device "flash:"
rommon 3 > dir bootflash:
dir: cannot access device "bootflash:"
rommon 4 > dir usbflash0:
program load complete, entry point: 0x8000f000, size: 0x3d240
open(): Open Error = -1
dir: cannot open device "usbflash0:"
rommon 5 > dir usbflash1:
program load complete, entry point: 0x8000f000, size: 0x3d240
open(): Open Error = -1
dir: cannot open device "usbflash1:"
rommon 6 > dir usbflash0:
program load complete, entry point: 0x8000f000, size: 0x3d240
open(): Open Error = -1
dir: cannot open device "usbflash0:"
rommon 7 > dir eprom:
dir: cannot access device "eprom:"
rommon 8 >

Leo Laohoo · ‎12-11-2017

Eject the CF. Make sure there's the CF slot is empty. Enter the command "dir flash:" and see what error message.
Next, slide a USB stick into the USB slot and enter the command "dir usbflash0:" (or "dir usbflash1:"). Post the output to the commands.

hill.tyrone@outlook.com · ‎12-12-2017

Below is the output as requested...

_______________________________________________________________________

System Bootstrap, Version 12.4(13r)T11, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2009 by cisco Systems, Inc.

Initializing memory for ECC
..
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
Compact Flash:not present
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
Entering rommon> prompt after several failed attempts to boot an IOS image.
Please check your internal/external flash drives for the correct IOS image
and issue 'reset' at the rommon> prompt to re-try the boot process.
rommon 1 > dev
Devices in device table:
id name
flash: compact flash
bootflash: boot flash
usbflash0: usbflash0
usbflash1: usbflash1
eprom: eprom
rommon 2 > dir flash:
dir: cannot open device "flash:"
rommon 3 > reset
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
Compact Flash:not present
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
Entering rommon> prompt after several failed attempts to boot an IOS image.
Please check your internal/external flash drives for the correct IOS image
and issue 'reset' at the rommon> prompt to re-try the boot process.
rommon 1 > dir usbflash0:
program load complete, entry point: 0x8000f000, size: 0x3d240
open(): Open Error = -1
dir: cannot open device "usbflash0:"
rommon 2 >

Leo Laohoo · ‎12-12-2017

And this is already with a known working USB stick connected to the router?

hill.tyrone@outlook.com · ‎12-12-2017

Yes, it is the same USB memory stick I was using before. I have some other memory sticks but they're too big to be formatted in FAT. You had said in a previous post "The USB flash drive works but the IOS could be corrupt."Thank you for following up.

Leo Laohoo · ‎12-12-2017

Try downloading the IOS again from the Cisco website.
After downloading, compare the MD5 hash value of the IOS downloaded against the MD5 hash value found in the Cisco website. If they match, then try forcing the router to boot the IOS via the USB stick.

hill.tyrone@outlook.com · ‎12-12-2017

Well I checked the MD5 on the IOS files that I have but none of the MD5 checks match, so I'm assuming I've been downloading some bad files. This is an old router and I don't have a service contract with Cisco so I can't download anything from the website. I found a couple links stating that there is a legal method to download firmware images for free but I'm not sure it will work. I don't really have any other option so I'm going to give it a try...

https://serverfault.com/questions/286620/how-to-obtain-cisco-ios-firmware

https://**bleep**.technology/free-cisco-ios-updates

Leo Laohoo · ‎12-12-2017

hill.tyrone@outlook.com wrote:

Well I checked the MD5 on the IOS files that I have but none of the MD5 checks match, so I'm assuming I've been downloading some bad files.

Well, this will definitely cause the router not to boot the IOS.

hill.tyrone@outlook.com · ‎12-13-2017

I thought I would still be able to see the files on the CF card or USB stick with DIR command but I guess I was wrong.

I didn't have any luck getting the IOS image from Cisco support so I decided my best option is to just order another 2811 router that comes with the IOS and just copy the files onto another CF card. Thanks for all your help.

hill.tyrone@outlook.com · ‎12-16-2017

Alright, so I got my second 2811 router so I could get a valid IOS image. It boots up fine without a problem so I copied the contents of the CF card to another CF card and tried booting my other router but it is still stuck in rommon mode. I also tried copying the files to a USB stick but it still would not boot. I then tried booting with the CF card that came with the second router but it still will not boot. I copied the console output from the attempts and posted it below. Any help or suggestions would be appreciated. Thank you.

_____________________________________________________________________________

System Bootstrap, Version 12.4(13r)T11, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2009 by cisco Systems, Inc.

Initializing memory for ECC
..
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80

program load complete, entry point: 0x8000f000, size: 0x310cb04

Error : compressed image checksum is incorrect 0x0AE743EB
Expected a checksum of 0x35FD3FEB

*** System received a Software forced crash ***
signal= 0x17, code= 0x5, context= 0x80014e20
PC = 0x8000f0d4, Cause = 0x20, Status Reg = 0x3040a803
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80

program load complete, entry point: 0x8000f000, size: 0x310cb04

Error : compressed image checksum is incorrect 0x114A3C0B
Expected a checksum of 0x35FD3FEB

*** System received a Software forced crash ***
signal= 0x17, code= 0x5, context= 0x80014e20
PC = 0x8000f0d4, Cause = 0x20, Status Reg = 0x3040a803
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80

program load complete, entry point: 0x8000f000, size: 0x310cb04

Error : compressed image checksum is incorrect 0x1B7F43FB
Expected a checksum of 0x35FD3FEB

*** System received a Software forced crash ***
signal= 0x17, code= 0x5, context= 0x80014e20
PC = 0x8000f0d4, Cause = 0x20, Status Reg = 0x3040a803
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80

program load complete, entry point: 0x8000f000, size: 0x310cb04

Error : compressed image checksum is incorrect 0x1BF33BFB
Expected a checksum of 0x35FD3FEB

*** System received a Software forced crash ***
signal= 0x17, code= 0x5, context= 0x80014e20
PC = 0x8000f0d4, Cause = 0x20, Status Reg = 0x3040a803
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80

program load complete, entry point: 0x8000f000, size: 0x310cb04

Error : compressed image checksum is incorrect 0x1E9C3BEB
Expected a checksum of 0x35FD3FEB

*** System received a Software forced crash ***
signal= 0x17, code= 0x5, context= 0x80014e20
PC = 0x8000f0d4, Cause = 0x20, Status Reg = 0x3040a803
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80

__________________________________________________________________

#Output from trying to boot from USB
__________________________________________________________________

System Bootstrap, Version 12.4(13r)T11, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2009 by cisco Systems, Inc.

Initializing memory for ECC
..
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
Compact Flash:not present
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
Entering rommon> prompt after several failed attempts to boot an IOS image.
Please check your internal/external flash drives for the correct IOS image
and issue 'reset' at the rommon> prompt to re-try the boot process.
rommon 1 > dev
Devices in device table:
id name
flash: compact flash
bootflash: boot flash
usbflash0: usbflash0
usbflash1: usbflash1
eprom: eprom
rommon 2 > boot usbflash0:
usbflash0: not present
rommon 3 > boot usbflash1:
program load complete, entry point: 0x8000f000, size: 0x3d240

*** TLB (Load/Fetch) Exception ***
Access address = 0x364
PC = 0x8003d878, Cause = 0x8, Status Reg = 0x3040a803

monitor: command "boot" aborted due to exception
rommon 4 > dir usbflash1:
Please reset before executing this command
rommon 5 > reset
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
Compact Flash:not present
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
Entering rommon> prompt after several failed attempts to boot an IOS image.
Please check your internal/external flash drives for the correct IOS image
and issue 'reset' at the rommon> prompt to re-try the boot process.
rommon 1 > dir usbflash1:
program load complete, entry point: 0x8000f000, size: 0x3d240

*** TLB (Load/Fetch) Exception ***
Access address = 0x364
PC = 0x8003d878, Cause = 0x8, Status Reg = 0x3040a803

monitor: command "dir" aborted due to exception
rommon 2 >

_________________________________________________________________________

#Output from second router with same CF card
_________________________________________________________________________

System Bootstrap, Version 12.4(13r)T11, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2009 by cisco Systems, Inc.

Initializing memory for ECC
..
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80

program load complete, entry point: 0x8000f000, size: 0x310cb04
Self decompressing the image : ########################################################################################################################################################################################################################################################################################### [OK]

Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
0003E7 0X00474800 C2811 Mainboard
0X00264050 Onboard VPN
0X000021B8 Onboard USB
0X002C29F0 public buffer pools
0X00211000 public particle pools
TOTAL: 0X00BAE3F8

If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 12Mb.
Using 2 percent iomem. [12Mb/512Mb]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(15)T9, RELEASE SOFTWARE (fc5)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Tue 28-Apr-09 13:09 by prod_rel_team
Image text-base: 0x400AF910, data-base: 0x437AF3A0

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Installed image archive
Cisco 2811 (revision 49.46) with 512000K/12288K bytes of memory.
Processor board ID FTX1528AH4Z
2 FastEthernet interfaces
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
126976K bytes of ATA CompactFlash (Read/Write)

--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: n

Press RETURN to get started!

*Dec 16 19:17:16.091: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to: Initialized
*Dec 16 19:17:16.099: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to: Enabled
*Dec 16 19:17:17.795: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to up
*Dec 16 19:17:17.795: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Dec 16 19:17:17.795: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
*Dec 16 19:17:17.795: %LINEPROTO-5-UPDOWN: Line protocol on Interface IPv6-mpls, changed state to up
*Dec 16 19:17:19.151: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down
*Dec 16 19:17:19.151: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down
*Dec 16 19:18:08.223: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down
*Dec 16 19:18:08.227: %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to administrativel
Router>
Routey down
*Dec 16 19:18:09.147: %IP-5-WEBINST_KILL: Terminating DNS process
*Dec 16 19:18:15.675: %SYS-5-RESTART: System restarted --
Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(15)T9, RELEASE SOFTWARE (fc5)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Tue 28-Apr-09 13:09 by prod_rel_team
*Dec 16 19:18:15.679: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
*Dec 16 19:18:15.907: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Dec 16 19:18:15.907: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF
*Dec 16 19:18:15.907: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Dec 16 19:18:15.907: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFFr>
Router>

____________________________________________________________

#Output from trying to boot from USB on second router
____________________________________________________________

System Bootstrap, Version 12.4(13r)T11, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2009 by cisco Systems, Inc.

Initializing memory for ECC
..
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
Compact Flash:not present
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
Entering rommon> prompt after several failed attempts to boot an IOS image.
Please check your internal/external flash drives for the correct IOS image
and issue 'reset' at the rommon> prompt to re-try the boot process.
rommon 1 > dev
Devices in device table:
id name
flash: compact flash
bootflash: boot flash
usbflash0: usbflash0
usbflash1: usbflash1
eprom: eprom
rommon 2 > dir usbflash0:
program load complete, entry point: 0x8000f000, size: 0x3d240
open(): Open Error = -1
dir: cannot open device "usbflash0:"
rommon 3 > dir usbflash1:
program load complete, entry point: 0x8000f000, size: 0x3d240

*** TLB (Load/Fetch) Exception ***
Access address = 0x364
PC = 0x8003d878, Cause = 0x8, Status Reg = 0x3040a803

monitor: command "dir" aborted due to exception
rommon 4 > boot usbflash0:
Please reset before booting
rommon 5 > reset
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
Compact Flash:not present
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
Entering rommon> prompt after several failed attempts to boot an IOS image.
Please check your internal/external flash drives for the correct IOS image
and issue 'reset' at the rommon> prompt to re-try the boot process.
rommon 1 > boot usbflash0:
usbflash0: not present
rommon 2 > boot usbflash1:
program load complete, entry point: 0x8000f000, size: 0x3d240

*** TLB (Load/Fetch) Exception ***
Access address = 0x364
PC = 0x8003d878, Cause = 0x8, Status Reg = 0x3040a803

monitor: command "boot" aborted due to exception
rommon 3 >

Leo Laohoo · ‎12-16-2017

In ROMmon, can you post the complete output to the command "set".

hill.tyrone@outlook.com · ‎12-18-2017

Below is the output from the set command.

___________________________________________________________________________

System Bootstrap, Version 12.4(13r)T11, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2009 by cisco Systems, Inc.

Initializing memory for ECC
..
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
open(): Open Error = -66
boot: cannot open "flash:"
boot: cannot determine first executable file name on device "flash:"
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
Entering rommon> prompt after several failed attempts to boot an IOS image.
Please check your internal/external flash drives for the correct IOS image
and issue 'reset' at the rommon> prompt to re-try the boot process.
rommon 1 > set
PS1=rommon ! >
FE_PORT=0
?=0
RET_2_RTS=16:27:26 UTC Thu Sep 2 2010
WARM_REBOOT=FALSE
RELOAD_TYPE=1
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1009613081
rommon 2 >

Leo Laohoo · ‎12-18-2017

I'm just looking at the previous output and this is what I can say:
1. The USB thumb drive is not a "supported" brand or variety;
2. The CF slot of the first router is, most likely, faulty.

hill.tyrone@outlook.com · ‎12-18-2017

Yeah, I had came to same conclusion that the CF card reader was bad. I have 2 CF cards that work in the other router but not on the old one. Since I figured the CF reader was bad and the USB stick was incompatible, I did some research into getting a different USB stick to boot. I came across this link, https://uwnthesis.wordpress.com/2015/08/31/how-to-convert-a-usb-into-fat-on-windows-7-for-plc-cisco-ios-usb/ , and I was able to get the newer router to boot off a 16GB USB stick but not on the old router. Below is the output from both routers booting off USB. I have the original files that were on the CF card from the old router, which is a different IOS than what came on the new router. I copied the both sets of files to the USB stick, not at the same time but 2 different attempts, but was still unable to get it to boot on the old router.

________________________________________________________________
New Router
________________________________________________________________

System Bootstrap, Version 12.4(13r)T11, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2009 by cisco Systems, Inc.

Initializing memory for ECC
..
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
Compact Flash:not present
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
Entering rommon> prompt after several failed attempts to boot an IOS image.
Please check your internal/external flash drives for the correct IOS image
and issue 'reset' at the rommon> prompt to re-try the boot process.
rommon 1 > dir usbflash1:
program load complete, entry point: 0x8000f000, size: 0x3d240
Directory of usbflash1:

14 32244652 -rw- c2800nm-ipbase-mz.150-1.M3.bin
0 0 -rw- 2GB
2 0 drw- System Volume Information
5 527849 -rw- 128MB.SDF
507 2900 -rw- cpconfig-2811.cfg
508 2938880 -rw- cpexpress.tar
553 1038 -rw- home.shtml
554 122880 -rw- HOME.TAR
556 1697952 -rw- securedesktop-ios-3.1.1.45-k9.pkg
582 415956 -rw- sslclient-win-1.1.4.176.pkg
rommon 2 > boot usbflash1:
program load complete, entry point: 0x8000f000, size: 0x3d240
program load complete, entry point: 0x8000f000, size: 0x3d240

program load complete, entry point: 0x8000f000, size: 0x1ec01e4
Self decompressing the image : ################################################################################################################################################################################################# [OK]

Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
0003E7 0X00474800 C2811 Mainboard
0X000021B8 Onboard USB
0X002C29F0 public buffer pools
0X00211000 public particle pools
-----------------------------------------------
TOTAL: 0X0094A3A8

If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 10Mb.
Using 1 percent iomem. [10Mb/512Mb]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 15.0(1)M3, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Sun 18-Jul-10 02:24 by prod_rel_team
Image text-base: 0x40016630, data-base: 0x42466D60

Cisco 2811 (revision 49.46) with 514048K/10240K bytes of memory.
Processor board ID FTX1528AH4Z
2 FastEthernet interfaces
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
3059696K bytes of USB Flash usbflash1 (Read/Write)

--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: n
% Crashinfo may not be recovered at flash:crashinfo
% This file system device reports an error

Press RETURN to get started!

*Dec 18 21:02:29.607: %SW_VLAN-4-IFS_FAILURE: VLAN manager encountered file operation error: call = ifs_open/read / code = 3588 (No device available)
/ bytes transfered = 0
*Dec 18 21:02:29.623: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Dec 18 21:02:29.623: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
*Dec 18 21:02:29.971: %USB_HOST_STACK-6-USB_DEVICE_CONNECTED: A Full speed USB device has been inserted in port 1.
*Dec 18 21:02:30.203: %USB_HOST_STACK-6-USB_DEVICE_DISCONNECTED: A USB device has been removed from port 0.
*Dec 18 21:02:30.891: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down
*Dec 18 21:02:30.891: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down
*Dec 18 21:02:30.899: %USBFLASH-5-CHANGE: usbflash1 has been inserted!
*Dec 18 21:03:25.547: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down
*Dec 18 21:03:25.547: %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to administratively down
*Dec 18 21:03:28.143: %IP-5-WEBINST_KILL: Terminating DNS process
*Dec 18 21:03:29.563: %SYS-5-RESTART: System restarted --
Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 15.0(1)M3, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Sun 18-Jul-10 02:24 by prod_rel_team
*Dec 18 21:03:29.575: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
Router>
Router>
Router>
Router>
Router>
Router>
Router>
Router>
Router>

System Bootstrap, Version 12.4(13r)T11, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2009 by cisco Systems, Inc.

Initializing memory for ECC
..
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
Compact Flash:not present
c2811 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled

Readonly ROMMON initialized
Entering rommon> prompt after several failed attempts to boot an IOS image.
Please check your internal/external flash drives for the correct IOS image
and issue 'reset' at the rommon> prompt to re-try the boot process.
rommon 1 > dir usbflash1:
program load complete, entry point: 0x8000f000, size: 0x3d240
Directory of usbflash1:

96 51432612 -rw- c2800nm-advipservicesk9-mz.124-15.T9.bin
0 0 -rw- 2GB
2 0 drw- System Volume Information
5 2900 -rw- cpconfig-2811.cfg
6 2941440 -rw- cpexpress.tar
51 1038 -rw- home.shtml
52 115712 -rw- HOME.TAR
54 1697952 -rw- securedesktop-ios-3.1.1.45-k9.pkg
80 415956 -rw- sslclient-win-1.1.4.176.pkg
87 527849 -rw- 128MB.SDF
rommon 2 > boot usbflash1:
program load complete, entry point: 0x8000f000, size: 0x3d240
program load complete, entry point: 0x8000f000, size: 0x3d240

program load complete, entry point: 0x8000f000, size: 0x310cb04
Self decompressing the image : ########################################################################################################################################################################################################################################################################################### [OK]

Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
0003E7 0X00474800 C2811 Mainboard
0X00264050 Onboard VPN
0X000021B8 Onboard USB
0X002C29F0 public buffer pools
0X00211000 public particle pools
TOTAL: 0X00BAE3F8

If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 12Mb.
Using 2 percent iomem. [12Mb/512Mb]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(15)T9, RELEASE SOFTWARE (fc5)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Tue 28-Apr-09 13:09 by prod_rel_team
Image text-base: 0x400AF910, data-base: 0x437A21F0

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Installed image archive
Cisco 2811 (revision 49.46) with 512000K/12288K bytes of memory.
Processor board ID FTX1528AH4Z
2 FastEthernet interfaces
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.

--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: n
% Crashinfo may not be recovered at flash:crashinfo
% This file system device reports an error

Press RETURN to get started!

*Dec 18 21:08:35.047: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to: Initialized
*Dec 18 21:08:35.055: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to: Enabled
*Dec 18 21:08:36.727: %USB_HOST_STACK-6-USB_DEVICE_CONNECTED: A Full speed USB device has been inserted in port 1.
*Dec 18 21:08:36.955: %USB_HOST_STACK-6-USB_DEVICE_DISCONNECTED: A USB device has been removed from port 0.
*Dec 18 21:08:37.083: %SW_VLAN-4-IFS_FAILURE: VLAN manager encountered file operation error: call = ifs_open/read / code = 3588 (No device available)
/ bytes transfered = 0
*Dec 18 21:08:37.095: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to up
*Dec 18 21:08:37.099: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Dec 18 21:08:37.099: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
*Dec 18 21:08:37.099: %LINEPROTO-5-UPDOWN: Line protocol on Interface IPv6-mpls, changed state to up
*Dec 18 21:08:38.099: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down
*Dec 18 21:08:38.099: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down
*Dec 18 21:08:42.647: fnu1362ControlTransfer Control Transfer did not complete! 1
*Dec 18 21:08:42.647: fnu1362ControlTransfer speed: 0x2, pipe: 0x80000080, status: 0x31
*Dec 18 21:08:42.647: fnu1362ControlTransfer, bmRequestType: 0x80, byRequest: 0x6, wValue: 0x100, wIndex: 0x0, wLength: 0x8
*Dec 18 21:08:42.655: %USB_HOST_STACK-5-USB_ENUM_FAIL_GETDESCR: Failed to enumerate a USB device as not able to read the device's description.
*Dec 18 21:09:49.083: %IP-5-WEBINST_KILL: Terminating DNS process
*Dec 18 21:09:49.435: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down
*Dec 18 21:09:49.435: %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to administratively down
*Dec 18 21:09:50.543: %SYS-5-RESTART: System restarted --
Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(15)T9, RELEASE SOFTWARE (fc5)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Tue 28-Apr-09 13:09 by prod_rel_team
*Dec 18 21:09:50.547: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
*Dec 18 21:09:50.771: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Dec 18 21:09:50.775: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF
*Dec 18 21:09:50.775: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Dec 18 21:09:50.775: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF
Router>