12-05-2017 12:11 PM - edited 03-05-2019 09:36 AM
Hello, I have two networks:
One with static routing and one vlan, and the other one with OSPF dynamic routing and one vlan.
I want to connect the two networks with a router and a copper crossover cable, but I haven't found a way to do it. I heard I have to do a routing redirecting but I don't know how. Any help?
Attached its the networks image.
Solved! Go to Solution.
12-05-2017 01:07 PM - edited 12-05-2017 01:20 PM
Thank you please let me try but first this is the configuration you should have:
I suggest remove the current OSPF and configure as following, give few seconds to complete the adjacency.
Configuration R1 (assume it is router 3)
router ospf 1
log-adjacency-changes
network 192.30.0.1 0.0.0.0 area 0
network 192.20.0.1 0.0.0.0 area 0
network 192.40.0.0 0.0.0.255 area 0
R2 configuration (please check the hostname)
router ospf 1
log-adjacency-changes
network 192.20.0.2 0.0.0.0 area 0
network 10.40.2.0 0.0.1.255 area 0
network 10.40.0.0 0.0.1.255 area 0
network 10.40.4.0 0.0.1.255 area 0
R3 Configuration
Router Rse (please check the hostnames)
router ospf 1
log-adjacency-changes
network 209.165.20.224 0.0.0.31 area 0
network 192.30.0.2 0.0.0.0 area 0
network 192.168.10.0 0.0.0.255 area 0
network 192.168.20.0 0.0.0.255 area 0
netwokr 192.168.30.0 0.0.0.255 area 0
12-05-2017 12:19 PM - edited 12-05-2017 12:21 PM
Hi
Could you please provide more details about the question? You could use dynamic routing protocol like EIGRP or OSPF to interconnect all the routers. Or use static routing but you must include the networks used to interconnect the routers for example:
RSede1
ip route x.x.x.x <subnet mask> <next hop IP of router 3 / local outgoing interface) ; Lan 1 in RSe router
ip route y.y.y.y <subnet mask> <next hop IP of router 3 / local outgoing interface) ; Lan 1 in RSe router
ip route z.z.z.z <subnet mask> <next hop IP of router 3 / local outgoing interface) ; P2P network between Router 3 and RSe router.
Now if one the network will be used with static routing and the other one will be used with dynamic routing you must redistribute the static routing into the routing protocol, for example:
Router 3
ip route x.x.x.x <subnet mask> <next hop IP of router RSede1 / local outgoing interface) ; Lan 1 in RSede1 router.
router eigrp 100 <used to interconnect router 3 and RSe router)
redistribute static.
:-)
12-05-2017 12:32 PM
Sorry I didn't understand completly your answer:
Router three has an ip address of 192.30.0.1 in the port that is connected with Rse, and rse has a ip of 192.30.0.2.
On the other hand, Router three has an ip address of 192.20.0.1 in the port that is connected with RSede1, and RSede1 has a ip of 192.20.0.2.
How would it be with dynamic routing?
12-05-2017 12:25 PM
Hi @icoltus
This is pretty simple. What is not working? Can you share you pkt file? Just rename it to something.txt and attach it. I can help you with the configuration.
-If I helped you somehow, please, rate it as useful.-
12-05-2017 12:34 PM
12-05-2017 12:36 PM - edited 12-05-2017 12:37 PM
Hi
What is the version of your Packet tracer? I have 7.
12-05-2017 12:42 PM
Version 7 too
12-05-2017 12:43 PM
12-05-2017 12:45 PM
Thank you so much
For any reason i cannot open it with my packet tracer, could you please zip the file and attach it here?
Thank you
12-05-2017 12:42 PM - edited 12-05-2017 12:43 PM
Based on this information you could have:
Router three has an ip address of 192.30.0.1 in the port that is connected with Rse, and rse has a ip of 192.30.0.2.
On the other hand, Router three has an ip address of 192.20.0.1 in the port that is connected with RSede1, and RSede1 has a ip of 192.20.0.2.
Router 3
router ospf 1
network 192.30.0.1 0.0.0.0 area 0
network 192.20.0.1 0.0.0.0 area 0
Router Sede1
router ospf 1
network 192.20.0.2 0.0.0.0 area 0
<you must include your LAN as well> example
192.168.1.0 0.0.0.255 area 0
Router RSe
router ospf 1
network 192.30.0.2 0.0.0.0 area 0
<you must include your LAN as well> example
192.168.2.0 0.0.0.255 area 0
12-05-2017 12:50 PM