cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2922
Views
0
Helpful
7
Replies

Enabling SSH

dj214
Level 1
Level 1

Hi - I need to implement SSH on 2 3600 series roouters running IOS 12.3(9). I read a few Cisco articles and although it looks easy. I cannot get it working. The commands do not work that are int h e DOC.

Can someone let me know how this is done or disable SSH altogether

Any help would be appreciated.

Thanks

7 Replies 7

Giuseppe Larosa
Hall of Fame
Hall of Fame

Hello DJ Stanley,

support of SSH depends on the specific feature set the IOS image is part of

if you post

sh ver | inc image

it will be possible to check if SSH is supported on your current IOS image

Hope to help

Giuseppe

Hi Stanley

To enable SSH on router you can run the below command also.

ip http secure server

Regards

Chetan kumar

Chetan,

The command you're referring to is to enable HTTPS on the router (not SSH).

To enable SSH first look you have a k8 or k9 image.

Please post the output of ''sh ver''

Federico.

Hi Federico

Please try this command with k9 image & let us know the output.

It work for both HTTPS & SSH.

& If any issue let us know .

Regards

Chetan kumar

Looks like this doesn't support. Anyway just to disable telnet. I don't really want to have to upgrade

the IOS on the 3 routers since there is always the possibility that it could go south.

SC3640-2#sh ver
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3640-IS-M), Version 12.3(9d), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Fri 01-Apr-05 10:15 by dchih
Image text-base: 0x60008B00, data-base: 0x61BB8000

ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
ROM: 3600 Software (C3640-IS-M), Version 12.3(9d), RELEASE SOFTWARE (fc2)

PSC3640-2 uptime is 28 weeks, 20 hours, 49 minutes
System returned to ROM by power-on
System image file is "flash:c3640-is-mz.123-9d.bin"

cisco 3640 (R4700) processor (revision 0x00) with 111616K/19456K bytes of memory.
Processor board ID 28724399
R4700 CPU at 100MHz, Implementation 33, Rev 1.0
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
4 FastEthernet/IEEE 802.3 interface(s)
DRAM configuration is 64 bits wide with parity disabled.
125K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

Hello DJ,

as Federico has correctly noted in the filename there should some special character to indicate SSH support

in your case the filename is

c3640-is-mz.123-9d.bin

i

: IP subset (SNMP, IP, Bridging, WAN, Remote Node, Terminal Services)

s: (NAT, IBM, MMP, VPDN/L2F) In 11.3T added VOIP

if there was a k8 or k9 or kn with n>=4 SSH support would be present

Hope to help

Giuseppe

Calin C.
Level 5
Level 5

If you still didn't find a solution you might check this tutorial;

http://www.firstdigest.com/2008/11/cisco-ssh-enable-disable-reconfigure-tutorial/

Review Cisco Networking for a $25 gift card