bridge-domain 10 bridge-domain 40 interface GigabitEthernet0/0/2 no ip address media-type rj45 negotiation auto service instance 10 ethernet encapsulation dot1q 10 rewrite ingress tag pop 1 symmetric bridge-domain 10 ! service instance 40 ethernet encapsulation dot1q 40 rewrite ingress tag pop 1 symmetric bridge-domain 40 ! interfaceBDI10 vrfforwardingmgmt ipaddress 10.20.20.1 255.255.255.0 ! interfaceucse 1/0/0 and ucse 2/0/0 no ip address no negotiation auto service instance 40 ethernet encapsulation dot1q 40 rewrite ingress tag pop 1 symmetric bridge-domain 40 ! interface BDI40 vrfforwardingmgmt ipaddress 10.20.40.1 255.255.255.0
Install the ESXi 5.5 or ESXi 6.0 on UCS-E via CMIC
From the admin PC connect to CIMC
Map the ESXi image
Change the boot order to boot into the mapped image
Continue installing ESXi
Configure the ESXi management settings to access it from the network
Configure the Vswitch and Port Groups with the appropriate VNIC
Make sure to set the network adapter to accept the following modes:
promiscuous, MAC address Changes and Forged Transmits.
Use sudo /usr/local/sf/bin/configure-network to configure the management settings Configure Management IP, Subnet and Default Gateway Open https GUI connection to add the NGFWv to FMC
User is prompted for EULA and post-boot configuration configure manager add <manager ip> <user chosen id>
Install the NGFWv (FTDv) on ESXi running on two different UCS-E modules
Repeat the steps above on the second UCS-E blade if configuring HA.
Router Configuration for FTD in HA in Routed Mode
EVC Configuration in ISR 4451 For UCSE 1/0/1, UCSE 2/0/1 and static configuration
bridge-domain 41 (failover) bridge-domain 15 interface ucse1/0/1 and ucse 2/0/1 no ip address no negotiation auto switchport mode trunk service instance 15 ethernet encapsulation dot1q 15 rewrite ingress tag pop 1 symmetric bridge-domain 15 ! service instance 41 ethernet encapsulation dot1q 41 rewrite ingress tag pop 1 symmetric bridge-domain 41 ! interface BDI15 mac-address 0001.0001.0001 ip address 10.10.10.1 255.255.255.0 ip nat inside ! ip route 10.20.20.0 255.255.255.0 10.10.10.10 ip route 10.20.30.0 255.255.255.0 10.10.10.10 ! ip route 0.0.0.0 0.0.0.0 18.104.22.168 ip route 22.214.171.124 255.255.255.255 10.10.10.10 ! ip nat inside source list NAT-ACL interface GigabitEthernet0/0/3 overload
UCS-E Exernal Ports (G2) for VLAN 21 and VLAN 31
No Configuration required in Router for the external interfaces connected to the Switch directly
The switch port connected to the UCS-E external ports should be enabled with the trunk port for VLANs ( in this use case vlan 21 and vlan 31)
Vmware ESXi host Network Configuration
NGFWv Interface to Port-Group Mapping
In case of E1000,FTDv use only one network adapter for mgmt. In case of VMXNET3, it consume two adapter for mgmt.
Using E1000,the FTDv interface to Network adapter mapping is in order, but using VMXNET3 it is random. when you change from E1000 to VMXNET3, you need to do correct mapping properly
Configure the NGFWv High Availability between them through Firepower Management Center(FMC)
NGFWv Interface Configuration and Status
NGFWv HA Failover Function (External Link failure Testing)
NGFWv HA Failover Function (Internal Link failure Testing)
NGFWv HA failover not triggered during the internal interface failure NGFWv HA Failover Function
Hi, We got 1 pair of ASA5525 in 1 room, and another pare of (new) ASA5525 in another room.Both pairs are configured as Active/Standby in each room (top one is active, bottom is standby).Both are independent rooms and the rooms are not meant to be red...
Hi all, I need your help/guidance in detecting the root cause and fixing the issue with Cisco AnyConnect via Wi-Fi. I've moved to another provider and implemented the following configuration: Provider's router (Nokia G-240W-C) in the bridge...
Hi all,we've got two vESAs with two mx records, both 10 and 10.if we send all traffic through all two of them everything works fine, or at least acceptable.If we send all traffic only to one appliance we've got the following queue working rate:  ...
I have 2 ASA5545 in HA cluster with firepower modules, both firepower modules are unresponsive.the question is:if we re-imaged one of the firepower modules, will this cause a failover, and this ASA unit will be active? or the module re-image is ...
Hello,ISE: 126.96.36.199, path 8Sorry if this question has already been asked here. What type of latency is represented under the system summary dashboard: RADIUS or TACACS? How is it measured? Thanks,Myky