on 04-10-2018 03:03 AM
iPXE boot in ASR9K
Migration recommendation document for Cxr to Exr.
Example : “asr9k-mini-x64-6.2.3.iso”
Config will be lost we needed to save the configuration in advance before migration on external server.
This can be done only on a RSP880 , RP2 and above .
Disk and hard disk would be formatted while migration we needed to save the configuration and relevant logs externally .
During migration from C-xr to E-xr (only using migration script )
Password recovery
When router boot up fails with E-xr .
During Downgrade from 6225 and below we needed to do Ipxe boot
iPXE is a pre-boot execution environment that is embedded in the router and works at the BIOS level. iPXE is used to re-image the system, boot the router in case of boot failure or in the absence of a valid bootable partition.
The following example shows the output of the command:
sysadmin-vm:0_RSP0# hw-module location all reload
Tue Mar 6 08:12:47.605 UTC
Reload hardware module ? [no,yes] yes
result Card graceful reload request on all acknowledged.
sysadmin-vm:0_RSP0#
Step 3 : If router is unable to boot then intiate an OIR of both RP (Active and Standby RP)
Press Ctrl +C as soon as you see this below log -
##########################################################
System Bootstrap, Version 10.57 [ASR9K x86 ROMMON],
Copyright (c) 1994-2014 by Cisco Systems, Inc.
Compiled on Mon 01/09/2017 17:15:01.98
BOARD_TYPE : 0x100317
Rommon : 10.57 (Primary)
Board Revision : 4
PCH EEPROM : 3.4
IPU FPGA(PL) : 0.40.0 (Backup)
IPU INIT(HW_FPD) : 0.30.0
IPU FSBL(BOOT.BIN) : 1.19.0
IPU LINUX(IMAGE.FPD) : 1.21.0
OPTIMUS FPGA : 0.12.0
OMEGA FPGA : 0.13.0
ALPHA FPGA : 0.14.0
CHA FPGA : 0.5.1
CBC0 : Part 1=34.38, Part 2=34.38, Act Part=2
Product Number : A9K-RSP880-SE
Chassis : ASR-9904-AC
Chassis Serial Number : FOX1936GBDD
Slot Number : 1
Pxe Mac Address LAN 0 : 70:e4:22:06:13:40
Pxe Mac Address LAN 1 : 70:e4:22:06:13:41
==========================================================
Got EMT Mode as 3
Got Boot Mode as 0
Booting IOS-XR (32 bit Classic XR) - Press Ctrl-c to stop
Step 4 : After aborting the boot process. you get the following options to boot as mentioned below and choose the option 4 for IPXE boot :
Please select the operating system and the boot device:
1) IOS-XR (32 bit Classic XR)
2) IOS-XR 64 bit Boot previously installed image
3) IOS-XR 64 bit Mgmt Network boot using DHCP server
4) IOS-XR 64 bit Mgmt Network boot using local settings (iPXE)
5) IOS-XR 64 bit Internal network boot from RSP/RP
6) IOS-XR 64 bit Local boot using embedded USB media
7) IOS-XR 64 bit Local boot using front panel USB media
Selection [1/2/3/4/5/6/7]:
Step 5 : After option 4 is selected please press CTRL+b as soon as you see this syslog on the router “Selected external PXE “to enter to IPXE prompt <IPXE>
The following logs for reference: -
Please select the operating system and the boot device:
1) IOS-XR (32 bit Classic XR)
2) IOS-XR 64 bit Boot previously installed image
3) IOS-XR 64 bit Mgmt Network boot using DHCP server
4) IOS-XR 64 bit Mgmt Network boot using local settings (iPXE)
(Press 'p' for more option)
Selection [1/2/3/4]: 4
Selected IOS-XR 64 bit Mgmt Network boot using local settings (iPXE), Continue ? Y/N: y
Serial ATA Port 4 : SMART iSATA SHSLM32GEBCITHD0
Serial ATA Port 5 : SMART iSATA SHSLM32GEBCITHD0
USB Device 1 : STEC STEC USB 2.0
Selected external PXE
Since response is not received for os_type, switch to IOS-XR 32 bit
CISCO iPXEiPXE initialising devices...ok
iPXE 1.0.0+ (f6488) -- Open Source Network Boot Firmware -- http://ipxe.org
Features: DNS HTTP TFTP EFI ISO9660 Menu
IPXE embed script.......
IPXE preference ...1
Using rommon variables....
ROMMON SETTINGS
...............
cisco/cisco-ipv4-address:string = 5.34.16.100
cisco/cisco-netmask-address:str = 255.255.0.0
cisco/cisco-gateway-address:str = 5.34.0.1
Err: cisco-server-url not set
cisco/cisco-server-url:string =
===============================================================================
NETWORK SETTINGS
................
net0/ip:ipv4 = 5.34.16.100
net0/gateway:ipv4 = 5.34.0.1
net0/netmask:ipv4 = 255.255.0.0
net0/mac:hex = 70:e4:22:06:13:40
net1/ip:ipv4 = 5.34.16.100
net1/gateway:ipv4 = 5.34.0.1
net1/netmask:ipv4 = 255.255.0.0
net1/mac:hex = 70:e4:22:06:13:41
..................
Press Ctrl-B for the iPXE command line...
Opening net0, close net1...
iPXE>
Set below variables in iPXE prompt if Rommon variables are not set.
iPXE>cisco/cisco-server-url:string=tftp://YOURSERVER_IP/auto/tftpboot-SMU/612/ASR9K/asr9k-mini-x64.iso
iPXE>cisco/cisco-ipv4-address:string=1.3.24.202
iPXE>cisco/cisco-netmask-address:str=255.255.0.0
iPXE>cisco/cisco-gateway-address:str=1.3.0.1
Note: where net0 represents mgmt port0 and net1 represents mgmt port1 :
now open the connected mgmt port (0/1) with this Command “ifopen net0/1 “ then boot the require image from tftp location or reachability.
And next open the front ports and execute the boot command in ipXE prompt
iPXE>ifclose net0
iPXE>ifclose net1
iPXE>ifopen net 1
iPXE>boot tftp://YOURSERVER_IP/file path/image.iso
The following example for reference for 623 image.
iPXE>
iPXE> ifopen net0:
iPXE> boot tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso
tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso... 0%
iPXE>
iPXE>
iPXE> boot tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso
tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso... 15%
iPXE>
iPXE> boot tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso
tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso... 74%
Memory required for image[asr9k-mini-x64-6.2.3.iso]: 1135456256, available: 1841299456
Booting iso-image@0x83c525000(1135456256), bzImage@0x83c55f000(4526671)
.......BIOS CODE SIGN ENTRY ...
!!!! IPXE boot syslogs logs !!!
Serial ATA Port 4 : SMART iSATA SHSLM32GEBCITHD02
Serial ATA Port 5 : SMART iSATA SHSLM32GEBCITHD02
Selected external PXE
CISCO iPXEiPXE initialising devices...ok
iPXE 1.0.0+ (f6488) -- Open Source Network Boot Firmware -- http://ipxe.org
Features: DNS HTTP TFTP EFI ISO9660 Menu
IPXE embed script.......
IPXE preference ...1
Using rommon variables....
ROMMON SETTINGS
...............
cisco/cisco-ipv4-address:string = 5.32.23.5
cisco/cisco-netmask-address:str = 255.255.0.0
cisco/cisco-gateway-address:str = 5.32.0.1
Err: cisco-server-url not set
cisco/cisco-server-url:string =
===============================================================================
NETWORK SETTINGS
................
net0/ip:ipv4 = 5.32.23.5
net0/gateway:ipv4 = 5.32.0.1
net0/netmask:ipv4 = 255.255.0.0
net0/mac:hex = d4:6d:50:64:74:e0
net1/ip:ipv4 = 5.32.23.5
net1/gateway:ipv4 = 5.32.0.1
net1/netmask:ipv4 = 255.255.0.0
net1/mac:hex = d4:6d:50:64:74:e1
..................
Press Ctrl-B for the iPXE command line...
iPXE>
iPXE>
iPXE>
iPXE> boot tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso
tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso... 0%
iPXE>
iPXE>
iPXE> boot tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso
tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso... 15%
iPXE>
iPXE> boot tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso
tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso... 74%
Memory required for image[asr9k-mini-x64-6.2.3.iso]: 1135456256, available: 1841299456
Booting iso-image@0x83c525000(1135456256), bzImage@0x83c55f000(4526671)
.......BIOS CODE SIGN ENTRY ...
Image ASR9K-Tomahawk verified successfully
**** PASS: secure boot verification of image: bzImage****
[output omitted]
Step 7 : ENTER THE NEW PASSWORD as prompted
!!!!!!!!!!!!!!!!!!!! NO root-system username is configured. Need to configure root-system username. !!!!!!!!!!!!!!!!!!!!
--- Administrative User Dialog ---
Enter root-system username: lab
Enter secret:
Use the 'configure' command to modify this configuration.
User Access Verification
Username:
!!!! ADMIN PROMPT syslogs !!!
Press RETURN to get started.
0/RSP0/ADMIN0:Mar 6 08:34:00.050 : vm_manager[3773]: %INFRA-VM_MANAGER-4-INFO : Info: vm_manager started VM default-sdr--1
0/RSP0/ADMIN0:Mar 6 08:34:41.933 : shelf_mgr[3761]: %INFRA-SHELF_MGR-4-CARD_RELOAD : Reloading card 0/1
0/1/ADMIN0:Mar 6 08:34:58.489 : inst_agent[3189]: %INFRA-INSTAGENT-2-SELF_TEST_FAILED : This node has failed verification of its installed software base. A new disk will be prepared.
0/RSP0/ADMIN0:Mar 6 08:36:55.208 : esdma[4962]: %PKT_INFRA-FM-4-FAULT_MINOR : ALARM_MINOR :ESDMA lost connectivity with ESD :DECLARE :0/LC1/LC_SW:
RP/0/RSP0/CPU0:ios#sh plat
Tue Mar 6 09:24:09.083 UTC
Node Type State Config state
--------------------------------------------------------------------------------
0/RSP0/CPU0 A9K-RSP880-SE(Active) IOS XR RUN NSHUT
0/RSP1/CPU0 A9K-RSP880-SE(Standby) IOS XR RUN NSHUT
0/FT0 ASR-9904-FAN OPERATIONAL NSHUT
0/1/CPU0 A9K-4X100GE-TR IOS XR RUN NSHUT
0/PT0 A9K-AC-PEM-V2 OPERATIONAL NSHUT
RP/0/RSP0/CPU0:ios#
RP/0/RSP0/CPU0:ios#
RP/0/RSP0/CPU0:ios#
RP/0/RSP0/CPU0:ios#sh install active summary
Tue Mar 6 09:24:12.488 UTC
Active Packages: 1
asr9k-xr-6.2.3 version=6.2.3 [Boot image]
RP/0/RSP0/CPU0:ios#
System Admin Username: lab
Password:
lab connected from 127.0.0.1 using console on sysadmin-vm:0_RSP0
sysadmin-vm:0_RSP0#
sysadmin-vm:0_RSP0#
sysadmin-vm:0_RSP0#
Step 8: Standby RP will Sync with active RP once active RP is booted successfully .
!!! Sys logs from standby console reference !!!
This (D)RP Node is not ready or active for login /configuration
Usage
hushd_platform.sh update_flash
boardtype flash_type : Update boardtype in flash
hushd_platform.sh get_bios_ver
boardtype flash_type : Get BIOS version from flash
Stopping
Stopping OpenBSD Secure Shell server: sshdinitctl: Unknown instance:
Stopping system message bus: dbus.
Stopping libvirtd daemon: [ OK ]
Stopping system log daemon...0
Stopping kernel log daemon...0
Stopping internet superserver: xinetd.
Stopping crond: OK
Stopping rpcbind daemon...
done.
Stopping S.M.A.R.T. daemon: smartd.
Stopping Lighttpd Web Server: stopped /usr/sbin/lighttpd (pid 3692)
lighttpd.
Deconfiguring network interfaces... done.
Sending all processes the KILL signal...
umount: /dev/mq: mountpoint not found
Tue Mar 6 08:13:04 UTC 2018: halt -w
Tue Mar 6 08:13:04 UTC 2018: Reboot Mode: 2, Hushd mode: 6, IPU: 20
Unmounting remote filesystems...
Deactivating swap...
Unmounting local filesystems...
mount: / is busy
Tue Mar 6 08:13:24 UTC 2018: halt -d -f -h
get_ipu_base: pci_attach failed
Tue Mar 6 08:13:24 UTC 2018: Reboot Mode: 2, Hushd mode: 6, IPU: 20
��Booting Main Processor
Transferring Console
[=3h[=3h[=3h��) ��)
CPU reset reason = 5 (CPU_RESET_POR)
##########################################################
System Bootstrap, Version 10.58 [ASR9K x86 ROMMON],
Copyright (c) 1994-2014 by Cisco Systems, Inc.
Compiled on Wed 01/25/2017 10:48:20.82
BOARD_TYPE : 0x100317
Rommon : 10.58 (Primary)
Board Revision : 4
PCH EEPROM : 3.4
IPU FPGA(PL) : 0.47.0 (Primary)
IPU INIT(HW_FPD) : 0.57.0
IPU FSBL(BOOT.BIN) : 1.103.0
IPU LINUX(IMAGE.FPD) : 1.103.0
OPTIMUS FPGA : 0.12.0
OMEGA FPGA : 0.16.0
ALPHA FPGA : 0.16.0
CHA FPGA : 0.6.1
CBC0 : Part 1=34.38, Part 2=34.38, Act Part=2
Product Number : A9K-RSP880-SE
Chassis : ASR-9904-AC
Chassis Serial Number : FOX1839H3NF
Slot Number : 2
Pxe Mac Address LAN 0 : 70:e4:22:06:13:40
Pxe Mac Address LAN 1 : 70:e4:22:06:13:41
==========================================================
Got EMT Mode as 2
Got Boot Mode as 0
Booting IOS-XR 64 bit Boot previously installed image - Press Ctrl-c to stop
Step 9 : If standby RP is not getting sync then press ctrl +C and select option 5 from boot.
Please select the operating system and the boot device:
1) IOS-XR (32 bit Classic XR)
2) IOS-XR 64 bit Boot previously installed image
3) IOS-XR 64 bit Mgmt Network boot using DHCP server
4) IOS-XR 64 bit Mgmt Network boot using local settings (iPXE)
(Press 'p' for more option)
Selection [1/2/3/4]:
Please select the operating system and the boot device:
1) IOS-XR (32 bit Classic XR)
2) IOS-XR 64 bit Boot previously installed image
3) IOS-XR 64 bit Mgmt Network boot using DHCP server
4) IOS-XR 64 bit Mgmt Network boot using local settings (iPXE)
(Press 'p' for more option)
Selection [1/2/3/4]: �Booting Main Processor
Transferring Console
Transferring Console
�[=3h[=3h[=3h����^�
CPU reset reason = 8 (CPU_RESET_WDOG_POR)
##########################################################
System Bootstrap, Version 10.58 [ASR9K x86 ROMMON],
Copyright (c) 1994-2014 by Cisco Systems, Inc.
Compiled on Wed 01/25/2017 10:48:20.82
BOARD_TYPE : 0x100317
Rommon : 10.58 (Primary)
Board Revision : 4
PCH EEPROM : 3.4
IPU FPGA(PL) : 0.47.0 (Primary)
IPU INIT(HW_FPD) : 0.57.0
IPU FSBL(BOOT.BIN) : 1.103.0
IPU LINUX(IMAGE.FPD) : 1.103.0
OPTIMUS FPGA : 0.12.0
OMEGA FPGA : 0.16.0
ALPHA FPGA : 0.16.0
CHA FPGA : 0.6.1
CBC0 : Part 1=34.38, Part 2=34.38, Act Part=2
Product Number : A9K-RSP880-SE
Chassis : ASR-9904-AC
Chassis Serial Number : FOX1839H3NF
Slot Number : 2
Pxe Mac Address LAN 0 : 70:e4:22:06:13:40
Pxe Mac Address LAN 1 : 70:e4:22:06:13:41
==========================================================
Got EMT Mode as 2
Got Boot Mode as 0
Booting IOS-XR 64 bit Boot previously installed image - Press Ctrl-c to stop
Checking peer OS type.
Serial ATA Port 4 : SMART iSATA SHSLM32GEBCITHD0
Serial ATA Port 5 : SMART iSATA SHSLM32GEBCITHD0ASR9K Host OS.......BIOS CODE SIGN ENTRY ...
Image ASR9K-Tomahawk verified successfully
Image Verification Passed
[output Omittted]
ios con0/RSP1/CPU0 is in standby
Once active has booted up, select option 5 from boot menu on standby to boot from active RP/RSP if not sync .
!!!! SYS Admin !!!!
Press RETURN to get started.
0/RSP0/ADMIN0:Mar 6 08:56:21.602 : shelf_mgr[3761]: %INFRA-SHELF_MGR-4-CARD_RELOAD : Reloading card 0/RSP1
0/RSP0/ADMIN0:Mar 6 08:57:11.207 : esdma[4962]: %PKT_INFRA-FM-4-FAULT_MINOR : ALARM_MINOR :ESDMA lost connectivity with ESD :DECLARE :0/RP1/RP_SW:
0/1/ADMIN0:Mar 6 09:00:01.743 : vm_manager[3572]: %INFRA-VM_MANAGER-4-INFO : Info: vm_manager started VM default-sdr--1
0/RSP0/ADMIN0:Mar 6 09:09:44.511 : esdma[4962]: %PKT_INFRA-FM-4-FAULT_MINOR : ALARM_MINOR :ESDMA lost connectivity with ESD :CLEAR :?/RP1/RP_SW:
0/RSP1/ADMIN0:Mar 6 09:09:57.495 : sdr_mgr[3962]: %SM-SDR_MANAGER-4-INFO : Info: SDR-RM Standby Initialized
0/RSP1/ADMIN0:Mar 6 09:09:57.509 : pm[3770]: %INFRA-Process_Manager-3-PROCESS_RESTART : Process led_mgr (IID: 0) restarted
0/RSP1/ADMIN0:Mar 6 09:09:57.550 : sdr_mgr[3962]: %SM-SDR_MANAGER-4-INFO : Info: SDR-SM Standby Initialized
0/RSP1/ADMIN0:Mar 6 09:12:31.405 : vm_manager[3977]: %INFRA-VM_MANAGER-4-INFO : Info: vm_manager started VM default-sdr--1
System Admin Username: lab
Password:
lab connected from 127.0.0.1 using console on sysadmin-vm:0_RSP0
sysadmin-vm:0_RSP0# sh plat
Tue Mar 6 09:23:27.624 UTC
Location Card Type HW State SW State Config State
----------------------------------------------------------------------------
0/1 A9K-4X100GE-TR OPERATIONAL OPERATIONAL NSHUT
0/RSP0 A9K-RSP880-SE OPERATIONAL OPERATIONAL NSHUT
0/RSP1 A9K-RSP880-SE OPERATIONAL OPERATIONAL NSHUT
0/FT0 ASR-9904-FAN OPERATIONAL N/A NSHUT
0/PT0 A9K-AC-PEM-V2 OPERATIONAL N/A NSHUT
sysadmin-vm:0_RSP0#
!!! XR Promp !!!!
ios con0/RSP0/CPU0 is now available
Press RETURN to get started.
0/RSP0/ADMIN0:Mar 6 08:56:21.602 : shelf_mgr[3761]: %INFRA-SHELF_MGR-4-CARD_RELOAD : Reloading card 0/RSP1
0/RSP0/ADMIN0:Mar 6 08:57:11.207 : esdma[4962]: %PKT_INFRA-FM-4-FAULT_MINOR : ALARM_MINOR :ESDMA lost connectivity with ESD :DECLARE :0/RP1/RP_SW:
0/1/ADMIN0:Mar 6 09:00:01.743 : vm_manager[3572]: %INFRA-VM_MANAGER-4-INFO : Info: vm_manager started VM default-sdr--1
0/RSP0/ADMIN0:Mar 6 09:09:44.511 : esdma[4962]: %PKT_INFRA-FM-4-FAULT_MINOR : ALARM_MINOR :ESDMA lost connectivity with ESD :CLEAR :?/RP1/RP_SW:
RP/0/RSP0/CPU0:Mar 6 09:09:49.764 : fpd-serv[157]: %PKT_INFRA-FM-3-FAULT_MAJOR : ALARM_MAJOR :FPD-NEED-UPGRADE :DECLARE :0/RSP1:
0/RSP1/ADMIN0:Mar 6 09:09:57.495 : sdr_mgr[3962]: %SM-SDR_MANAGER-4-INFO : Info: SDR-RM Standby Initialized
0/RSP1/ADMIN0:Mar 6 09:09:57.509 : pm[3770]: %INFRA-Process_Manager-3-PROCESS_RESTART : Process led_mgr (IID: 0) restarted
0/RSP1/ADMIN0:Mar 6 09:09:57.550 : sdr_mgr[3962]: %SM-SDR_MANAGER-4-INFO : Info: SDR-SM Standby Initialized
0/RSP1/ADMIN0:Mar 6 09:12:31.405 : vm_manager[3977]: %INFRA-VM_MANAGER-4-INFO : Info: vm_manager started VM default-sdr--1
RP/0/RSP0/CPU0:Mar 6 09:13:21.991 : rmf_svr[142]: %PKT_INFRA-FM-2-FAULT_CRITICAL : ALARM_CRITICAL :RP-RED-LOST-PNP :CLEAR :0:
RP/0/RSP0/CPU0:Mar 6 09:14:11.905 : rmf_svr[142]: %PKT_INFRA-FM-3-FAULT_MAJOR : ALARM_MAJOR :RP-RED-LOST-NSRNR :CLEAR :0:
RP/0/RSP0/CPU0:Mar 6 09:14:58.672 : rmf_svr[142]: %HA-REDCON-1-STANDBY_READY : standby card is ready
RP/0/RSP0/CPU0:Mar 6 09:15:08.673 : rmf_svr[142]: %PKT_INFRA-FM-3-FAULT_MAJOR : ALARM_MAJOR :RP-RED-LOST-NNR :CLEAR :0:
User Access Verification
Username: lab
Password:
RP/0/RSP0/CPU0:ios#
RP/0/RSP0/CPU0:ios#
RP/0/RSP0/CPU0:ios#
RP/0/RSP0/CPU0:ios#
RP/0/RSP0/CPU0:ios#sh plat
Tue Mar 6 09:24:09.083 UTC
Node Type State Config state
--------------------------------------------------------------------------------
0/RSP0/CPU0 A9K-RSP880-SE(Active) IOS XR RUN NSHUT
0/RSP1/CPU0 A9K-RSP880-SE(Standby) IOS XR RUN NSHUT
0/FT0 ASR-9904-FAN OPERATIONAL NSHUT
0/1/CPU0 A9K-4X100GE-TR IOS XR RUN NSHUT
0/PT0 A9K-AC-PEM-V2 OPERATIONAL NSHUT
RP/0/RSP0/CPU0:ios#
RP/0/RSP0/CPU0:ios#
RP/0/RSP0/CPU0:ios#
RP/0/RSP0/CPU0:ios#sh install active summary
Tue Mar 6 09:24:12.488 UTC
Active Packages: 1
asr9k-xr-6.2.3 version=6.2.3 [Boot image]
RP/0/RSP0/CPU0:ios#
Preparing system for backup. This may take a few minutes especially for large configurations.
Status report: node0_RSP0_CPU0: START TO BACKUP
Status report: node0_RSP0_CPU0: BACKUP HAS COMPLETED SUCCESSFULLY
[Done]
Proceed with reload? [confirm]
On active and standby XR console, HIT CTRL-C to view BIOS MENU. Select option 3 to boot " IOS-XR 64 bit External network boot using DHCP setting".
If active and standby are not stopped at boot menu, they will continue booting with previously known / saved settings.
There is 10 seconds time to hit CTRL-C when below message is seen on screen.
If system is inactive in BOOT MENU for 30 minutes, watchdog resets the RP/RSP and system will try to boot using last known settings.
Booting IOS-XR 32 bit - Press Ctrl-c to stop
Booting IOS-XR 64 bit Disk boot - Press Ctrl-c to stop
Please select the operating system and the boot device:
1) IOS-XR 32 bit
2) IOS-XR 64 bit Disk boot
3) IOS-XR 64 bit External network boot using DHCP setting
4) IOS-XR 64 bit External network boot using ROMMON setting
(Press 'p' for more option)
Selection [1/2/3/4]: 3
IOS-XR 64 bit External network boot using DHCP setting
, Continue ? Y/N: y
Serial ATA Port 4 : SMART iSATA SHSLM32GEBCITHD02
Serial ATA Port 5 : SMART iSATA SHSLM32GEBCITHD02
Once active has booted up, select option 5 from boot menu on standby to boot from active RP/RSP if not sync .
---- END ---
I am stuck in the below flow. Not able to reach iPXE prompt.
Booting IOS-XR 64 bit Boot previously installed image - Press Ctrl-c to stop
X
Please select the operating system and the boot device:
1) IOS-XR (32 bit Classic XR)
2) IOS-XR 64 bit Boot previously installed image
3) IOS-XR 64 bit Mgmt Network boot using DHCP server
4) IOS-XR 64 bit Mgmt Network boot using local settings (iPXE)
(Press 'p' for more option)
Selection [1/2/3/4]: 4
Selected IOS-XR 64 bit Mgmt Network boot using local settings (iPXE), Continue ? Y/N: Y
Serial ATA Port 4 : SMART SATA SHSLM32G3BCITHD22
Serial ATA Port 5 : SMART SATA SHSLM32G3BCITHD22
USB Device 1 : VT eUSB
Other Device 1 : SMART SATA SHSLM32G3BCITHD22
Other Device 2 : SMART SATA SHSLM32G3BCITHD22
Selected external PXE
Since response is not received for os_type, switch to IOS-XR 32 bit
CISCO iPXEiPXE initialising devices...ok
iPXE 1.0.0+ (534c5) -- Open Source Network Boot Firmware -- http://ipxe.org
Features: DNS HTTP TFTP EFI ISO9660 Menu
IPXE embed script.......
IPXE preference ...1
Using rommon variables....
ROMMON SETTINGS
...............
Could not store "ip": Invalid argument (http://ipxe.org/1c056082)
Boot Succeeded - CISCO iPXE
Booted IOS-XR 64 bit Mgmt Network boot using local settings (iPXE), press any key to reload
I am planning to clean install using front panel USB media.
Is the USB media format FAT32?
Should I save the eXR ISO Image in the Root directory of the USB media?
Can I select images to boot from multiple ISO files in the USB media? (Does it fail if there are multiple files?)
IPXE IPV6 boot is supported?
Can you please share the procedure?
Since you don't have any ROMMON variables configured, You need to select option 1 first (32 bit Classic), break & enter ROMMON, configure ROMMON IP/Mask etc, then reboot to the 64-bit boot menu again & then select Option 4. From there you can hit CTRL-B and enter iPXE.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: