Buy or Renew
Buy or Renew
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
3801
Views
10
Helpful
4
Replies

Nexus 5548UP - VFC error disabled

Go to solution
Robert Leers
Level 1
Level 1

‎10-24-2013 02:01 AM

We are building a Datacenter with UCS 6248U FIs and Nexus 5548UP Switches.

The problem ist the FCoE configuration on the Nexus. After creating the vfC-Interface it is member of the default-vsan1. When we try to assign it to an other vsan (here vsan 100), it goes down with "error disabled".

We have only the Interface e1/7 in port-channel 60 bound to vfc60, vsan 100 associated to vlan 710

I hope anybody has an idea what's the problem.

Here is an extract of our configuration:

RZ1NX001(config-if)# show run int e1/7
interface Ethernet1/7
  description FCoE Link to RZ2FI-A eth1/19
  switchport mode trunk
  switchport trunk allowed vlan 710
  channel-group 60 mode active
--------------------------------------
RZ1NX001(config-if)# show int e1/7
Ethernet1/7 is up
  Hardware: 1000/10000 Ethernet, address: 002a.6a53.5c2e (bia 002a.6a53.5c2e)
  Description: FCoE Link to RZ2FI-A eth1/19
  MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec
  reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA
  Port mode is trunk
  full-duplex, 10 Gb/s, media type is 10G
  Beacon is turned off
  Input flow-control is off, output flow-control is off
  Rate mode is dedicated
  Switchport monitor is off
  EtherType is 0x8100
-----------------------------------------
RZ1NX001(config-if)# show run int po60
interface port-channel60
  switchport mode trunk
  switchport trunk allowed vlan 710
  spanning-tree port type edge trunk
  speed 10000
-----------------------------------------
RZ1NX001(config-if)# show int po60
port-channel60 is up
  Hardware: Port-Channel, address: 002a.6a53.5c2e (bia 002a.6a53.5c2e)
  MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec
  reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA
  Port mode is trunk
  full-duplex, 10 Gb/s
  Input flow-control is off, output flow-control is off
  Switchport monitor is off
  EtherType is 0x8100
  Members in this channel: Eth1/7
------------------------------------------
RZ1NX001(config-if)# show run int vfc60
interface vfc60
  bind interface port-channel60
  switchport trunk allowed vsan 100
  no shutdown
------------------------------------------
RZ1NX001(config-if)# show int vfc60
vfc60 is down (Error disabled)
    Bound interface is port-channel60
    Hardware is Ethernet
    Port WWN is 20:3b:00:2a:6a:53:5c:7f
    Admin port mode is F, trunk mode is on
    snmp link state traps are enabled
    Port vsan is 100
-------------------------------------------
RZ1NX001(config-if)# show vlan fcoe
Original VLAN ID        Translated VSAN ID      Association State
----------------        ------------------      -----------------
      710                       100              Operational
Labels:
0 Helpful
1 Accepted Solution

Accepted Solutions

Go to solution
padramas
Cisco Employee
Cisco Employee
In response to Robert Leers

‎10-24-2013 06:21 AM

Hello Robert,

The port-channel status is SD and member link is still I state. Have you tried flapping the port-channel interfaces ?

Also, NPV feature is enabled on N5K and I don't see NPIV  enabled on it.

Are you planning to run N5K in NPV mode ? If yes, I need to verify if FI can be connected to FC switch operating in NPV mode.

I guess FI is in FC End host mode ( NPV ) and it needs to be connected to FC switch with NPIV feature.

Padma

View solution in original post

4 Replies 4

Go to solution
padramas
Cisco Employee
Cisco Employee

‎10-24-2013 03:16 AM

Hello Robert,

What is the UCSM and N5K version ?

From N5K

show feature | grep -i enabled

show fcoe

From UCS FI

connect nxos

show port-channel summary

--- same set of commands as you shared from N5K

Padma

0 Helpful

Go to solution
Robert Leers
Level 1
Level 1
In response to padramas

‎10-24-2013 04:04 AM

Hello Padma,

N5K-Version is version 5.1(3)N2(1)

UCS-Manager is 2.1(2a)

We've configured the UCS with UCSM but the result looks similar to the N5K: 



N5K:




--------------------------------------------




RZ1NX001# show feature | grepp i enabled


                             ^


% Invalid command at '^' marker.


RZ1NX001# show feature | grep -i enabled


fcoe                  1         enabled


fex                   1         enabled


interface-vlan        1         enabled


lacp                  1         enabled


lldp                  1         enabled


npv                   1         enabled


ospf                  1         enabled (not-running)


ospf                  2         enabled (not-running)


ospf                  3         enabled (not-running)


ospf                  4         enabled (not-running)


sshServer             1         enabled


vpc                   1         enabled




----------------------------------------------




RZ1NX001# show fcoe


RZ1NX001#




(no output)




-----------------------------------------------


-----------------------------------------------




FI:




RZ1FI001-A(nxos)# show port-channel summary


Flags:  D - Down        P - Up in port-channel (members)


        I - Individual  H - Hot-standby (LACP only)


        s - Suspended   r - Module-removed


        S - Switched    R - Routed


        U - Up (port-channel)


--------------------------------------------------------------------------------


Group Port-       Type     Protocol  Member Ports


      Channel


--------------------------------------------------------------------------------


60    Po60(SD)    Eth      LACP      Eth1/19(I)


1026  Po1026(SU)  Eth      NONE      Eth1/1(P)    Eth1/2(P)    Eth1/3(P)


                                     Eth1/4(P)


1283  Po1283(SD)  Eth      NONE      Eth2/1/9(D)  Eth2/1/11(D)


1290  Po1290(SD)  Eth      NONE      Eth2/1/13(D)  Eth2/1/14(D)  Eth2/1/15(D)


                                     Eth2/1/16(D)


1292  Po1292(SD)  Eth      NONE      Eth2/1/17(D)  Eth2/1/18(D)  Eth2/1/19(D)


                                     Eth2/1/20(D)


1293  Po1293(SD)  Eth      NONE      Eth2/1/21(D)  Eth2/1/22(D)  Eth2/1/23(D)


                                     Eth2/1/24(D)


1295  Po1295(SD)  Eth      NONE      Eth2/1/29(D)  Eth2/1/30(D)  Eth2/1/31(D)


                                     Eth2/1/32(D)


1307  Po1307(SU)  Eth      NONE      Eth2/1/1(P)  Eth2/1/2(P)  Eth2/1/3(P)


                                     Eth2/1/4(P)


1309  Po1309(SU)  Eth      NONE      Eth2/1/5(P)  Eth2/1/6(P)  Eth2/1/7(P)


                                     Eth2/1/8(P)




--------------------------------------------------------






RZ1FI001-A(nxos)# show run int e1/19




!Command: show running-config interface Ethernet1/19


!Time: Thu Oct 24 10:42:28 2013




version 5.0(3)N2(2.11.2a)




interface Ethernet1/19


  description C: FcoeUplink


  pinning border


  switchport mode trunk


  switchport trunk allowed vlan 710,4048


  channel-group 60 mode active


  no shutdown






----------------------------------------------------------




RZ1FI001-A(nxos)# show int e1/19


Ethernet1/19 is up


  Hardware: 1000/10000 Ethernet, address: 002a.6a3b.523a (bia 002a.6a3b.523a)


  Description: C: FcoeUplink


  MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,


     reliability 255/255, txload 1/255, rxload 1/255


  Encapsulation ARPA


  Port mode is trunk


  full-duplex, 10 Gb/s, media type is 10G


  Beacon is turned off


  Input flow-control is off, output flow-control is off


  Rate mode is dedicated


  Switchport monitor is off


  EtherType is 0x8100




-----------------------------------------------------------




RZ1FI001-A(nxos)# show run int po60




!Command: show running-config interface port-channel60


!Time: Thu Oct 24 10:45:04 2013




version 5.0(3)N2(2.11.2a)




interface port-channel60


  description C: FcoeUplink


  switchport mode trunk


  pinning border


  switchport trunk allowed vlan 710,4048


  speed 10000






------------------------------------------------------------




RZ1FI001-A(nxos)# show int po60


port-channel60 is down (No operational members)


  Hardware: Port-Channel, address: 002a.6a3b.523a (bia 002a.6a3b.523a)


  Description: C: FcoeUplink


  MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,


     reliability 255/255, txload 1/255, rxload 1/255


  Encapsulation ARPA


  Port mode is trunk


  auto-duplex, 10 Gb/s


  Beacon is turned off


  Input flow-control is off, output flow-control is off


  Switchport monitor is off


  EtherType is 0x8100


  Members in this channel: Eth1/19






---------------------------------------------------------------




RZ1FI001-A(nxos)# show vlan fcoe




Original VLAN ID        Translated VSAN ID      Association State


----------------        ------------------      -----------------




      4048                      1                Operational


      710                       100              Operational






-----------------------------------------------------------------






RZ1FI001-A(nxos)# show run int vfc 792




interface vfc792


  bind interface port-channel60


  switchport mode NP


  no shutdown




------------------------------------------------------------------




RZ1FI001-A(nxos)# show int vfc792




vfc792 is down (Error disabled)


    Bound interface is port-channel60


    Hardware is Virtual Fibre Channel


    Port WWN is 23:17:00:2a:6a:3b:52:7f


    Admin port mode is NP, trunk mode is on


    snmp link state traps are enabled


    Port vsan is 100


    1 minute input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec


    1 minute output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec


      0 frames input, 0 bytes


        0 discards, 0 errors


      0 frames output, 0 bytes


        0 discards, 0 errors


    last clearing of "show interface" counters never




------------------------------------------------------------------




RZ1FI001-A(nxos)# show vsan 100


vsan 100 information


         name:VSAN0100  state:active


         interoperability mode:default


         loadbalancing:src-id/dst-id/oxid


         operational state:down
0 Helpful

Go to solution
padramas
Cisco Employee
Cisco Employee
In response to Robert Leers

‎10-24-2013 06:21 AM

Hello Robert,

The port-channel status is SD and member link is still I state. Have you tried flapping the port-channel interfaces ?

Also, NPV feature is enabled on N5K and I don't see NPIV  enabled on it.

Are you planning to run N5K in NPV mode ? If yes, I need to verify if FI can be connected to FC switch operating in NPV mode.

I guess FI is in FC End host mode ( NPV ) and it needs to be connected to FC switch with NPIV feature.

Padma

Go to solution
Robert Leers
Level 1
Level 1
In response to padramas

‎10-24-2013 09:03 AM

Hello Padma,

this was the solution. After enabling npiv the vfc  shows "NPV upstream port not available". After disabling npv everthing  is fine. I confused npv and npiv.

Thank you for your help

Robert

Customers Also Viewed These Support Documents

Review Cisco Networking for a $25 gift card