storage-vdc(config-if)# show module
Mod Ports Module-Type Model Status
--- ----- ----------------------------------- ------------------ ----------
2 32 1/10 Gbps Ethernet Module N7K-F132XP-15 ok
sw1-gd78(config-if)# sh module
Mod Ports Module-Type Model Status
--- ----- ----------------------------------- ------------------ ----------
2 48 1/2/4/8 Gbps FC Module DS-X9248-96K9 ok
4 8 10 Gbps FCoE Module DS-X9708-K9 ok
7 0 Supervisor/Fabric-2a DS-X9530-SF2AK9 active *
8 0 Supervisor/Fabric-2a DS-X9530-SF2AK9 ha-standby
10 22 4x1GE IPS, 18x1/2/4Gbps FC Module DS-X9304-18K9 ok
Mod Sw Hw World-Wide-Name(s) (WWN)
--- -------------- ------ --------------------------------------------------
2 5.2(2) 1.1 20:41:00:0d:ec:fb:8a:00 to 20:70:00:0d:ec:fb:8a:00
4 5.2(2) 0.107 --
7 5.2(2) 1.8 --
8 5.2(2) 1.8 --
10 5.2(2) 1.3 22:41:00:0d:ec:fb:8a:00 to 22:52:00:0d:ec:fb:8a:00
sw1-gd78(config-if)# sh run int ethernet4/6
!Command: show running-config interface Ethernet4/6
!Time: Mon Feb 20 22:56:12 2012
version 5.2(2)
interface Ethernet4/6
no shutdown
sw1-gd78(config-if)# no shut
sw1-gd78(config-if)# speed 1000
ERROR: Ethernet4/6: Configuration does not match the port capability.
sw1-gd72# sh int ethernet4/6 capabilities
Ethernet4/6
Model: DS-X9708-K9
Type (SFP capable): 10Gbase-SR
Speed: 1000,10000
Duplex: full
Trunk encap. type: 802.1Q
Channel: yes
Broadcast suppression: percentage(0-100)
Flowcontrol: rx-(off/on/desired),tx-(off/on/desired)
Rate mode: dedicated
QOS scheduling: rx-(2q4t),tx-(1p3q4t)
CoS rewrite: yes
ToS rewrite: yes
SPAN: yes
UDLD: yes
Link Debounce: yes
Link Debounce Time: yes
MDIX: no
Port Group Members: none
TDR capable: no
FabricPath capable: yes
Port mode: Switched
sw1-gd72# sh int ethernet4/6 transceiver details
Ethernet4/6
transceiver is present
type is 10Gbase-SR
name is CISCO-FINISAR
part number is FTLX8571D3BCL-CS
revision is C
serial number is FNS12090EMJ
nominal bitrate is 10300 MBit/sec
Link length supported for 50/125um OM2 fiber is 82 m
Link length supported for 50/125um OM3 fiber is 300 m
Link length supported for 62.5/125um fiber is 26 m
cisco id is --
cisco extended id number is 4
SFP Detail Diagnostics Information (internal calibration)
----------------------------------------------------------------------------
Alarms Warnings
High Low High Low
----------------------------------------------------------------------------
Temperature 36.21 C 75.00 C -5.00 C 70.00 C 0.00 C
Voltage 3.29 V 3.63 V 2.97 V 3.46 V 3.13 V
Current 8.11 mA 11.80 mA 4.00 mA 10.80 mA 5.00 mA
Tx Power -2.65 dBm 1.49 dBm -11.30 dBm -1.50 dBm -7.30 dBm
Rx Power -2.21 dBm 1.99 dBm -13.97 dBm -1.00 dBm -9.91 dBm
Transmit Fault Count = 0
----------------------------------------------------------------------------
Note: ++ high-alarm; + high-warning; -- low-alarm; - low-warning
