Hi Team,   Can any one help me to know the output discard limitation of the below module.    ws-x6748-ge-tx ... View more

Thanks alot.  Qos we can configure in vlan, port-channel or interface level, can you clarify this?   ... View more

Hi Joseph,   Tanks for the clarification. Could you please share some cisco doc where it is telling the QOS feature compatability in "RSP720-3C-GE" and share the document where it is telling  sup ports are often QoS feature poor compared to some line card ports.     ... View more

RSP card is there in slot 5.   Mod Ports Card Type Model Serial No. --- ----- -------------------------------------- ------------------ ----------- 1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX *********** 5 2 Route Switch Processor 720 (Hot) RSP720-3C-GE *********** 6 2 Route Switch Processor 720 (Active) RSP720-3C-GE *********** Mod MAC addresses Hw Fw Sw Status --- ---------------------------------- ------ ------------ ------------ ------- 1 0021.d8ef.5d48 to 0021.d8ef.5d77 3.0 12.2(18r)S1 12.2(33)SRE8 Ok 5 0007.0e61.e994 to 0007.0e61.e997 5.2 12.2(33r)SRC 12.2(33)SRE8 Ok 6 001c.584c.8f8c to 001c.584c.8f8f 5.7 12.2(33r)SRC 12.2(33)SRE8 Ok Mod Sub-Module Model Serial Hw Status ---- --------------------------- ------------------ ----------- ------- ------- 1 Centralized Forwarding Card WS-F6700-CFC *********** 4.1 Ok 5 Policy Feature Card 3 7600-PFC3C *********** 1.1 Ok 5 C7600 MSFC4 Daughterboard 7600-MSFC4 *********** 1.1 Ok 6 Policy Feature Card 3 7600-PFC3C *********** 1.1 Ok 6 C7600 MSFC4 Daughterboard 7600-MSFC4 *********** 1.1 Ok Mod Online Diag Status ---- ------------------- 1 Pass 5 Pass 6 Pass   So what is the next action plan need to take before configuring the MLS QOS in the chassi.?     Please suggest on the above. ... View more

yes am using Radius server  in order to authenticate the user and using DHCP as well in the network. I have observed that when ever we are configuring the authentication end users are unable to get the IP address.can you please suggest on this . ... View more

Hi Richard, Let me summaries. i have created  2 policy in my router.   route-map VPL_Traffic permit 10 match ip address VPL set ip next-hop <ip address> ! route-map VPL_Traffic permit 20 !   same policy am calling in interface GigabitEthernet1/9.   interface GigabitEthernet1/9 description BSNL  P2P Link  bandwidth 10240 ip address <--------------> ip flow ingress ip flow egress ip policy route-map VPL_Traffic ip ospf network point-to-point ip ospf cost 100 load-interval 30 speed 100 duplex full   Is this "route-map VPL_Traffic permit 20" policy conf with out set command will create High cpu or not? please clarify the above... ... View more

Hi George, Let me brief out the issue. Below is the config.   route-map VFL_Traffic permit 20 ! route-map permit-all deny 1 match ip address proxy_ip ! route-map permit-res deny 6 match ip address prefix-list VGL_N Is the above config will cause high cpu? How PBR will create ARP packets which will cause CPU high? ... View more

Hi, If we aar running Mstp in cisco end and Rstp in dell switch end how the election will happen is there any changes will happen if dell switch will is using in distribution  ... View more

Hi george,   Running ios is "s72033-adventerprisek9_wan-mz.122-33.SXJ10.bin" ... View more

Hi George,   Thanks for the replay.   The query is. + I have 2 cisco 6513(core SW1,SW2) both are configured HSRP. + For core sw1 --> standby 128 priority 105 configured in HSRP + For core SW2 --> standby 128 priority 110 + Server is in Vlan 128. + when we are trying to ping from server to outside network packet is going through Core SW2 (Reason--> standby 128 priority is 110 ) + Both core switch are running MSTP and in distribuion (Dell switch) running RSTP. + As per spanning tree output core switch 1 is root bridge for vlan 128 at same time we can observe Gi11/43, Gi11/44 which is connected from core sw 1 --> distribuion(dell sw1)ports are going for Altn BLK. + In net working we are using load sharing mechanism. Hope this is clear.Please clarify why the rootbridge port is in ALT blocking state. ... View more