Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Andrew Woolman
Stats
Member since
05-27-2012
8
Posts
0
Helpful
0
Solutions
Created by
Andrew Woolman
in Network Management
in Network Management
01-29-2019
03:54 PM
01-29-2019
03:54 PM
Try removing the space in the site name. Worked for me.
... View more
Created by
Andrew Woolman
in Switching
in Switching
08-20-2018
06:58 PM
08-20-2018
06:58 PM
Sounds like a cable problem to me. Check out the TDR commands
https://community.cisco.com/t5/network-architecture-documents/how-to-use-time-domain-reflectometer-tdr/ta-p/3119327
and check for duplex issues
I would probably upgrade the IOS or at the very least reboot the switch
... View more
03-20-2016
10:45 PM
This is how I did it and it seemed to work. I don't know if the #MODE_ENABLE works show I entered the command is if I were in Global Config. Also note no space between the question (<IQ> and the response <R>
#INTERACTIVE
do copy tftp://10.50.22.87/MOH/$MOHFilename flash:/media/$MOHFilename<IQ>/media/$MOHFilename<R>/media/$MOHFilename
telephony-service
moh flash:/media/$MOHFilename
Hope this helps
... View more
12-22-2015
03:27 PM
3 years later and I've run into this issue too. Cisco want us to just use a 2048bit CA cert with SHA-1 when really they should upgrade the firmware of the phone to support 4096 SHA-2
... View more
08-02-2015
07:48 PM
Did you ever work this out? I'm trying to do the same thing with an access list. I need to add a host to an access list based on the site subnet which I was hoping to get from the switch vlan management IP address
... View more
Created by
Andrew Woolman
in Other Wireless - Mobility Subjects
in Other Wireless - Mobility Subjects
07-30-2013
08:30 PM
07-30-2013
08:30 PM
We have a number of cards with the same issue. It appears to be a hardware problem.
... View more
05-27-2012
05:48 PM
I've been experiencing the same issue and I think I may have the answer. I think the IOS version may have something to do with it. Perhaps a newer version has a different XML schema (I don't know much about XML). I removed the lines 30 YES from the license file and it installed fine. You can open the .lic file in notepad. Good luck
... View more
Created by
Andrew Woolman
in Network Management
01-29-2019
01-29-2019
Try removing the space in the site name. Worked for me.
08-20-2018
Sounds like a cable problem to me. Check out the TDR commands
https://community.cisco.com/t5/network...
03-20-2016
This is how I did it and it seemed to work. I don't know if the
#MODE_ENABLE works show I entered th...
12-22-2015
3 years later and I've run into this issue too. Cisco want us to just
use a 2048bit CA cert with SHA...
08-02-2015
Did you ever work this out? I'm trying to do the same thing with an
access list. I need to add a hos...
Created by
Andrew Woolman
in Other Wireless - Mobility Subjects
07-30-2013
07-30-2013
We have a number of cards with the same issue. It appears to be a
hardware problem.
Public Statistics
| Date Registered | 05-27-2012 05:40 PM |
| Date Last Visited | 02-05-2019 03:55 PM |
| Total Messages Posted | 8 |
