Hello Everyone,I am currently facing a critical issue during the deployment of Cisco DNA Center (Catalyst Center) version 2.3.7.5. Despite having adequate resources allocated (32 vCPU(60Ghz Reserved), 256GB(Reserved) RAM, 2.4TB NVMe), the system-mana...
Dears,While we are installing a new version on the DNA center version 2 , we got some errors after 1 hour.appsvc-remediation Application and Service Remediation 1.3.1007 - DEPLOYMENT_ERROR - Exception in package: syst...
Hello,We want to upgrade our customer's Nexus 9300 switches using ISSU but according to the Cisco documentation LACP timers set to fast rate is not supported for ISSU upgrades. The Cisco documentation for Catalyst Center Appliance installation says t...
As ASR1001-X is EOL by 31st July 2027, what is a better replacement out of Cisco Catalyst 8000 series router for a hub SDWAN with vManage/vSmart integration, BGP/MPLS/Internet aggregation, high‑throughput IPsec and redundant HA design?If we are to re...
Hi!We recently upgraded our DNA Center from 2.3.5.5 to Catalyst Center 2.3.7.10. We noticed that some devices that were originally managed without any problems, now show up as "ping reachable" under Inventory. If we reprovision and resync the devices...
Hello, We are planning to migrate our virtual 9800 from VMware to Nutanix. That WLC is part of the SDA fabric.Is there a way to deploy the new VM without changing IP address? Or is this not possib
Switch(config)#ip routing% Incomplete command. Cisco IOS XE Software, Version 17.15.04Cisco IOS Software [IOSXE], IE3x00 Switch Software (IE3x00-UNIVERSALK9-M), Version 17.15.4, RELEASE SOFTWARE (fc6) Technology Package License Information:----------...
Hello Everyone,Looking for some guidance on SDA migration. We have around 10K users spread across several floors. Need to migrate the site to SD-Access. We intend to do this floor-by-floor cutover. Please note, majority of the users are on wireless a...
Hello everyone,I'm going to deploy Catalyst Center VM version 2.3.7 in VMware ESXi, and I have a question regarding Catalyst deployment How many VM node I need to deploy the Cisco Catalyst Center VMs in cluster mode for HA? best regardsYounes
Looking for insights from the SDA/CTS community regarding an interesting VXLAN GBP behavior observed in an SDA deployment with Extended Node (SBEN) topology.Printer->SBEN swtich(9200CX-8UXG-2X -17.5.4) -> FE (9300-48UN) -Intermediate node switch(9500...
One of our customer's is running CatC version 2.3.7.10.70209.10 but they are still getting no data on the last seen column when generating a report based on data for the last 7 days. Based on this Cisco bug this was fixed, or am I understanding this ...
Hello,I'm inquiring about Meraki Catalyst 9300L stack cabling. I've installed Meraki Catalyst 9300L switches for the first time and connected the stacking cables in an X-shape configuration. Is it possible to connect two switches with stack cabling i...
We currently have DNAC managing switches and wireless lan controllers, no fabric sites, which integrates ISE PSNs as AAA server both Radius and TACACS, say 10.0.0.11 and 10.0.0.12. Admin node (10.0.0.10) is not added to DNAC. all sites are not fabric...
Hey Smarter People,I’m running Catalyst Center and currently have Event Notifications set up to email us when a switch goes down using the “Switch Unreachable” event. What I’m trying to figure out now is how to get an email when the switch comes back...
After upgrading to DNAC 2.3.7.11, we encountered a similar issue where previously working 'admin' account stopped working and we had to configure another account in ISE (with SUPER-ADMIN rights) to make this integration working again. While doing th...
