Hello NAT is supported on IPBase images. The image c2600-ipbase-mz.123-26.bin supports the following NAT features: NAT - Default Inside Server Enhancement NAT - Stateful Fail-over of Network Address Translation (SNAT) Phase 1 NAT - Ability to use Routes Maps with Static Translations NAT - Enhanced H.225/H.245 Forwarding Engine NAT - Network Address Translation NAT - Static Mapping Support with HSRP for High-Availability NAT - Support for NetMeeting Directory (Internet Locator Service - ILS) NAT - Support of H.323v2 Call Signaling (FastConnect) NAT - Support of H.323v2 RAS NAT - Translation of external IP Addresses only NAT-Support of IP Phone to Cisco Call Manager Regards Sush ... View more

Hi Ibrahim Sorry...here is the correct one: SPA-1X10GE-L-V2  is HH. SPA-10X1GE-L-V2 is FHeight. If you are making use of half-height SPAs, you can use upto 4 half height SPA's in a SIP-10 module. But in case you want to make use of full height SPAs, you should use upto 2 full height SPAs. Cisco ASR 1000-SIP10-Supports: - 4 half height (Rate or full rate or combination) SPAs with up to 16 ports per SPA -2 full height (Rate or full rate or combination) SPAs with up to 32 ports per SPA -2 half height and 1 full height comb in at on that does not exceed 64 ports -Up to 10 Gbps of oversubscription The SIP40 allows up to 40 Gbps of bandwidth capacity between the SIP carrier card and the ESP forwarding engine, as opposed to 10 Gbps for the SIP10. Max ESP throughput that you could get on ASR1004 chassis is 40 Gbps (20Gbps in and 20Gbps out---> 20G unidirectional & 40 G bidirectional) which requires ESP40G forwarding plane and SIP40 carrier card. You can refer to this document to understand this better: http://www.cisco.com/en/US/prod/collateral/routers/ps9343/qa_C67-443177.html Regards Sush ... View more

Hi Ibrahim Cisco ASR 1004 with 2 SIPs supports 8 half-height SPAs. The 10- and 40-Gbps Cisco ASR 1000 Series SIP can support up to four half-height or two full-height SPAs or two half-height and one full-height SPAs. http://www.cisco.com/en/US/prod/collateral/routers/ps9343/qa_c67-496324.html Hence, as SPA-1X10GE-L-V2 is a full height SPA, 4 such SPAs can't be supported in a single SIP module. Regards Sush ... View more

Hi Satwinder Could you please get me the output of 'show version'? Kindly refer to the following document for SSH configuration: http://www.cisco.com/en/US/docs/ios-xml/ios/sec_usr_ssh/configuration/xe-3s/sec-usr-ssh-xe-3s-book.pdf Could you specify which command is not working in SNMP on your ASR box? Regards Sush ... View more

Hello 880 series supports a single universal image with Cisco Software Activation.  The active feature set is determined by the software license installed on the platform. In this case, VRF Lite is only supported when the Adv. IP feature license is installed. Router#show license Index 1 Feature: advipservices         Period left: Life time         License Type: Permanent         License State: Active, In Use         License Count: Non-Counted         License Priority: Medium Regards Sush ... View more

Hi Berni Indeed, anything else should not be affected. Unfortunately, I couldn't find any document yet. I would surely provide you the link if I find any. Moving from Port-based QOS To VLAN based QOS is also supposed to help. Regards Sush ... View more

Hi The following error message indicates the presence of a faulty NVRAM:      ERROR in NVRAM sizing. NVRAM could be bad! Hence, this can be rectified by replacing the chassis. Regards Sush ... View more

Hello Berni The following error message indicates that the switch has reached the hardware limitation:      %QM-4-AGG_POL_EXCEEDED QoS Hardware Resources Exceeded Out of Aggregate policers. Only a limited number of aggregate policers can be supported. On EARL7-based switches, this limit is 1023. Some QOS commands other than the police command are a part of this count. Any policy using 'set' or 'trust' command would increment the aggregate policer count. You can disable the addition of the set or trust commands to the aggregate policer count by entering the 'no mls qos marking statistics' command, but you will then be unable to collect statistics for the classmaps associated with these commands. Thanks Sush ... View more