Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About gavinspost
Stats
Member since
05-03-2010
4
Posts
0
Helpful
0
Solutions
08-08-2011
07:22 AM
Hi Is it possible to have a WS-C3750G-12S-S and a WS-C3750X-24T-L in the same stack, if so do they need to both be running the same software version/IOS. Thanks in advance. Gavin
... View more
Labels:
05-25-2011
12:46 PM
Hi I would appreciate if anyone could help me on this, I have the following setup: Internal network(branch)---->ASA5505 <------->BT ADSL(dynamic IP, NAT)<-------Internet------->ASA5510<----Internal network(HQ) We have created an easyvpn between the branch ASA5505 and the HQ ASA5510 which is up, however we can ping a host in the HQ network from the branch network but we cannot ping hosts in the branch network from the HQ network. The ASA5505 has been configured in Network Extension Mode but there is not a route for the branch network in the routing table. As the ASA5505 is actually on a private IP address behind the BT ADSL router do I need to enable any static NAT rules or port forwarding? Also should I being using NAT on the ASA5505 or set it up just for routing. Any thoughts would be greatly appreciated. Gavin
... View more
Labels:
05-03-2010
07:50 PM
ok, I eventually worked out what I was doing wrong, the thresholds were incorrectly configured and I didn't understand fully how they worked. I now have another query - I have configured a event manager command to run a cli action and email the results based on a syslog pattern. When I use the follwoing command it works: event syslog pattern "%RTT-3-IPSLATHRESHOLD" However I'm going to be running multiple SLAs and I want to send an email out for each one. When I try the following command it fails to match the syslog pattern and the emails doesn't get sent. event syslog pattern "%RTT-3-IPSLATHRESHOLD: IP SLAs(1): Threshold exceeded for rtt" Debug May 4 12:28:28.155: %RTT-3-IPSLATHRESHOLD: IP SLAs(1): Threshold exceeded for rtt May 4 12:28:28.163: fh_fd_syslog_event_match: num_matches = 0 May 4 12:28:28.163: fh_fd_data_syslog: num_matches = 0
... View more
05-03-2010
04:15 AM
I'm not sure if I have entered this questions into the correct disscusion group I have created an IP SLA using Jitter-Path for an MPLS link, I have also created a reaction-configuration entry with a threshold of 1 5 for the round trip time(rtt). I have scheduled the IP SLA to run continuously. When I do the 'Show IP SLA 1 Statistics' the rtt does rise above 5ms at times however I never recieve an event in the syslog, actually that's a lie I see one random threshold entry and then nothing, once the IP SLA has reached do I need to schedule a reset or something?. That brings me to my second question, I would like to match the threshold pattern in the syslog and send out an email with the 'Show IP SLA 1 Statistics' results in the body of the email. Any advice would be greatly appreciated. Thanks in advance Gavin
... View more
Labels:
08-08-2011
HiIs it possible to have a WS-C3750G-12S-S and a WS-C3750X-24T-L in the
same stack, if so do they ne...
05-25-2011
HiI would appreciate if anyone could help me on this, I have the
following setup:Internal network(br...
05-03-2010
ok, I eventually worked out what I was doing wrong, the thresholds were
incorrectly configured and I...
Public Statistics
| Date Registered | 05-03-2010 03:57 AM |
| Date Last Visited | 08-18-2017 03:54 AM |
| Total Messages Posted | 4 |
