Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Beth Steiger
05-08-2019
Beth Steiger
Member since
07-09-2012
Beginner
04-18-2018
03:14 PM
Thank you. We are now thinking it might be a problem with that circuit (it's new) and have the vendor looking into that.
... View more
04-18-2018
10:00 AM
Thank you. I do appreciate your time.
I only put it as a passive interface as not to cause issues during business hours. I can remove it after hours and try those commands again.
Here is my BGP config
router bgp 12345 bgp log-neighbor-changes network yyy.xxx.184.212 mask 255.255.255.252 redistribute connected neighbor yyy.xxx.184.213 remote-as 7018 neighbor yyy.xxx.184.213 soft-reconfiguration inbound
Do you think the following will work?
router eigrp xxxx
network (ip address)
no passive-interface GigabitEthernet0/2
no router bgp 12345
ip route 0.0.0.0 0.0.0.0 (ip address)
My concern is I will lose connection with the no router bgp and no be able to get the ip route command in. When I put the ip route command in first, I get disconnected.
Thanks again.
... View more
04-18-2018
09:27 AM
Hello Deepak,
Thank you for the reply. The reboot was due to me telling it to reload in x minutes. I did that so that if I lost connection, it would reload from the startup config and I wouldn't have to make the long drive out there.
I currently have have that interface set as passive, but this is what I get with the commands you requested:
EIGRP-IPv4 Neighbors for AS(1234)
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP a - application route + - replicated route, % - next hop override, p - overrides from PfR Gateway of last resort is xxx.yyy.184.213 to network 0.0.0.0
... View more
04-18-2018
09:08 AM
Hello,
We just put in fiber at one of our rural locations. I am hoping to do this configuration remotely with a reload in x as a backup.
The site is currently on an MPLS using BGP. I need to move it over to our fiber cloud, which uses EIGRP. I configure the interface and it shows up/up.
Here is part of my configuration
interface GigabitEthernet0/2 ip address zz.xxx.1.19 255.255.255.240 duplex auto speed auto router eigrp 1234 network zz.0.0.0
When I put in my route
ip route 0.0.0.0 0.0.0.0 (ip address)
I get booted and have to wait for the device to reloads to try again.
I am thinking BGP is my problem as I don't see EIGRP here:
Gateway of last resort is yyy.xxx.184.213 to network 0.0.0.0 B* 0.0.0.0/0 [20/0] via yyy.xxx.184.213, 00:03:32 zz.0.0.0/8 is variably subnetted, 12 subnets, 4 masks C zz.yyy.0.24/29 is directly connected, GigabitEthernet0/0.320 L zz.yyy.0.25/32 is directly connected, GigabitEthernet0/0.320 C zz.yyy.1.16/28 is directly connected, GigabitEthernet0/2 L zz.yyy.1.19/32 is directly connected, GigabitEthernet0/2 C zz.xxx.18.0/24 is directly connected, GigabitEthernet0/0.18 L zz.xxx.18.1/32 is directly connected, GigabitEthernet0/0.18 B zz.xxx.57.0/24 [20/0] via zzz.xxx.184.213, 00:03:32 B zz.xxx.58.0/24 [20/0] via zzz.xxx.184.213, 00:03:32 C zz.xxx.zz3.0/24 is directly connected, GigabitEthernet0/0.zz3 L zz.xxx.zz3.1/32 is directly connected, GigabitEthernet0/0.zz3 B zz.xxx.zz5.0/24 [20/0] via yyy.xxx.184.213, 00:03:32 B zz.xxx.zz6.0/24 [20/0] via yyy.xxx.184.213, 00:03:32 yyy.0.0.0/8 is variably subnetted, 5 subnets, 2 masks B yyy.85.249.68/30 [20/0] via yy.92.184.213, 00:03:32 C yyy.92.184.212/30 is directly connected, Multilink1 L yyy.92.184.214/32 is directly connected, Multilink1 B yyy.115.48.40/30 [20/0] via yyy.92.184.213, 00:03:32 B yyy.115.151.232/30 [20/0] via yyy.92.184.213, 00:03:32 yyy.89.0.0/16 is variably subnetted, 6 subnets, 3 masks B yyy.89.152.56/29 [20/0] via yyy.92.184.213, 00:03:32 B yyy.89.152.128/28 [20/0] via yyy.92.184.213, 00:03:32 B yyy.89.154.152/29 [20/0] via yyy.92.184.213, 00:03:32 B yyy.89.157.160/28 [20/0] via yyy.92.184.213, 00:03:32 B yyy.89.183.96/27 [20/0] via yyy.92.184.213, 00:03:32 B yyy.89.183.224/27 [20/0] via yyy.92.184.213, 00:03:32
I am concerned if I do a
No router bgp xxxxx, I will get booted again.
I would appreciate any advice.
Thank you!
... View more
Labels:
Currently, 1.4 Patch 10. We
in Wireless Security and Network Management
07-18-2017
06:26 AM
07-18-2017
06:26 AM
Currently, 1.4 Patch 10. We use FTP. I also had it happen with 2.1, which was a miserable experience. So bad, we rolled back.
... View more
For anyone else that may have
in Wireless Security and Network Management
07-17-2017
08:34 AM
07-17-2017
08:34 AM
For anyone else that may have this issue, the only way I know how to resolve it is to reload ISE.
... View more
Created by
Beth Steiger
in Other Network Architecture Subjects
in Other Network Architecture Subjects
08-01-2016
08:26 AM
08-01-2016
08:26 AM
We have had a horrible experience with 2.1 and are rolling back tonight. Some of our issues had to do with Windows 10 wireless authentication, massive backups, the massive size of ISE itself and multiple crashes (which I think have to do with the size of the deployment). At this time, I would not recommend this version. I am wondering if 2.0 is any better...
Just curious, are you still having issues?
... View more
06-13-2016
12:02 PM
Hello,
We were notified today that our ISE licensing was getting ready to expire (expires October 2016). We have since imported the new license file, which essentially doubled the count. We are thinking we need to delete the old file. Before we do, I have some questions:
* Is that the right thing to do?
* Will it impact the system if done during production hours?
* Is there anything else I should be concerned about in regard to removing this file?
Personas:
Administration, Monitoring, Policy Service (All)
Role:
STANDALONE
System Time:
Jun 13 2016 12:01:38 PM PST8PDT
FIPS Mode:
Disabled
Version:
1.4.0.253
Patch Information:
5
Thank you in advance for your assistance.
... View more
Labels:
Created by
Beth Steiger
in Policy and Access
in Policy and Access
01-25-2016
03:04 PM
01-25-2016
03:04 PM
Hello,
I am tasked with upgrading ISE to 1.4. Part of the instruction state the following:
"If you are upgrading a Cisco ISE node on a virtual machine (VM) from Release 1.2 or 1.2.1, after you upgrade, ensure that you power down the VM and change the Guest Operating System to Red Hat Enterprise Linux 6 (64-bit), and power the VM on after the change. "
Is this something that can be done when I shut the machine down for the snapshot? I have to bring another person in for the VM side of things and would like to get everything done sooner rather than later.
After this, I will then be looking at going to 2.0. If anyone has any tips, tricks or other advice they would like to offer, I would love to hear them. :)
Thanks you!
... View more
Labels:
01-14-2016
10:11 AM
Thank you! I have supressed it by the NAS IP address so it is no longer blowing up ISE. I really appreciate your help.
... View more
01-14-2016
08:49 AM
The identity is my user name. This happens the entire time I am logged in via the web interface.
... View more
01-14-2016
08:34 AM
It's coming from a Brocade ADX 1000. It only seems to happen when logged in via the web. Not when I ssh.
- Note this is a new device and the only one we have on line at the moment.
... View more
Created by
Beth Steiger
in Identity Services Engine (ISE)
05-02-2019 05:42 PM
05-02-2019 05:42 PM
I just updated 2.4 to patch 8 and am still seeing the same error. Like
you, I wonder if the fix made...
Created by
Beth Steiger
in Routing
04-18-2018 03:14 PM
04-18-2018 03:14 PM
Thank you. We are now thinking it might be a problem with that circuit
(it's new) and have the vendo...
Created by
Beth Steiger
in Routing
04-18-2018 10:00 AM
04-18-2018 10:00 AM
Thank you. I do appreciate your time. I only put it as a passive
interface as not to cause issues du...
Created by
Beth Steiger
in Routing
04-18-2018 09:27 AM
04-18-2018 09:27 AM
Hello Deepak, Thank you for the reply. The reboot was due to me telling
it to reload in x minutes. I...
Created by
Beth Steiger
in Routing
04-18-2018 09:08 AM
04-18-2018 09:08 AM
Hello, We just put in fiber at one of our rural locations. I am hoping
to do this configuration remo...
Created by
Beth Steiger
in Wireless Security and Network Management
07-18-2017 06:26 AM
07-18-2017 06:26 AM
Currently, 1.4 Patch 10. We use FTP. I also had it happen with 2.1,
which was a miserable experience...
Created by
Beth Steiger
in Wireless Security and Network Management
07-17-2017 08:34 AM
07-17-2017 08:34 AM
For anyone else that may have this issue, the only way I know how to
resolve it is to reload ISE.
Created by
Beth Steiger
in Identity Services Engine (ISE)
11-09-2016 06:01 AM
11-09-2016 06:01 AM
We had so many issues with this release, we ended up rolling back. I
need to revisit this at some po...
Created by
Beth Steiger
in Other Network Architecture Subjects
08-01-2016 08:26 AM
08-01-2016 08:26 AM
We have had a horrible experience with 2.1 and are rolling back tonight.
Some of our issues had to d...
Created by
Beth Steiger
in Identity Services Engine (ISE)
07-29-2016 06:56 AM
07-29-2016 06:56 AM
Thank you both. The reason I ask is when we looked at doing this in the
past, I contacted TAC and th...
Created by
Beth Steiger
in Identity Services Engine (ISE)
07-28-2016 03:41 PM
07-28-2016 03:41 PM
Hello,Has anyone successfully changed the hostname on an ISE 2.1.0.474
Standalone installation? We l...
Created by
Beth Steiger
in Identity Services Engine (ISE)
07-07-2016 09:58 AM
07-07-2016 09:58 AM
It looks like the patch for this problem regressed in 2.1. The engineer
I am working with is contact...
Created by
Beth Steiger
in Identity Services Engine (ISE)
06-30-2016 02:16 PM
06-30-2016 02:16 PM
Thank you. It is build 1511. I have opened a ticket with TAC. I will try
to update this with the sol...
Created by
Beth Steiger
in Identity Services Engine (ISE)
06-30-2016 01:16 PM
06-30-2016 01:16 PM
More info:OpenSSLErrorMessage SSL alert: code=0x228=552 ; source=local ;
type=fatal ; message="hands...
Created by
Beth Steiger
in Identity Services Engine (ISE)
06-30-2016 12:07 PM
06-30-2016 12:07 PM
Hello,I was wondering if anyone has seen issues with Windows 10 and ISE
2.1.0.474. We just upgraded ...
Public Statistics
| Date Registered | 07-09-2012 09:12 AM |
| Date Last Visited | 05-08-2019 10:19 AM |
| Total Messages Posted | 43 |
| Total Helpful Votes Received | 5 |
