Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About pirinoe1920
Stats
Member since
04-24-2006
14
Posts
0
Helpful
0
Solutions
Created by
pirinoe1920
in IP Telephony and Phones
in IP Telephony and Phones
03-09-2014
03:17 PM
03-09-2014
03:17 PM
We have a 2801 router with CME 8.1 and CUE 3.2.3. We receive calls on 3 analog lines into a 4 port FXO card. When calls arrive they reach an Automated Attendant which routes the calls properly. The issue we encounter is that the analog lines do not disconnect the calls quickly once the caller disconnects. It takes approximately 140 seconds before the calls disconnect. We have the following configuration on our FXO cards for each line. voice port 0/0/0 to 0/0/2 voice-port 0/0/2 trunk-group main 1 timeouts call-disconnect 1 timeouts ringing infinity timeouts wait-release 1 connection plar 1053 description PSTN XXX-XXX-XXXX caller-id enable Any ideas for what we are missing? Thanks
... View more
Labels:
03-09-2014
03:09 PM
Manish,
Thanks. I have added this command to all 3 voice ports 0/0/0 to 0/0/2 but I still have a delay of 140 seconds before the line disconnects. The calls route into the AA but when I hang up it still shows FXOLS_Connect for the 140 seconds. Any other ideas?
... View more
03-08-2014
10:50 PM
I am trying to understand how FXO ports work. I have little experience with this so I am trying to learn how it works at our office. We have a Cisco 2801 with CME 8.1 and CUE 3.2. The 2801 has a VIC2-4FXO card in it. It has 3 analog phone lines attached to it and are setup in a hunt group by the carrier. There is an Auto Attendant setup that prompts a caller with various options for redirecting calls. 1. Question: When a call comes into the Auto Attendant, I assume this ties up a single analog line. If there is a second call into the main number it also goes to the Auto Attendant and is routed to the number or appropriate voicemail. Would this tie up a second analog line? 2. Question: If a phone in the office is used to make an outbound call or a person in the office calling someone outside of the office at the same time as above, then would this tie up the 3rd analog line? 3. Question: If there is another person calling the AA at the same time as the previous 2 questions. We get a busy signal. Does this mean that all 3 analog lines are currently busy and no other call can come in or be made out due to the 3 lines being currently used? When I run the following commands on the router# sh voice call sum port 0/0/0 S_Connect FXOLS_Connect port 0/0/1 S_Connect FXOLS_Connect port 0/0/2 S_Connect FXOLS_Connect Also when a port is used and the caller hangs up the phone it takes between 30 and120 seconds for the call to release. Is this normal for analog lines to take time to release in the phone system? Are all these things normal or if I am having busy calls then do we have something configured improperly? Thanks for any help
... View more
Labels:
03-05-2014
02:33 PM
I made these changes but it still rings busy. Would this be something that the carrier has to configure? How would I be able to test this to know if the carrier has configured the hunt group or roll over feature correctly?
... View more
Created by
pirinoe1920
in IP Telephony and Phones
in IP Telephony and Phones
02-24-2014
04:17 PM
02-24-2014
04:17 PM
Hello guys, we recently took over a phone system and it has the following problem. When someone calls in and leaves a voicemail message the message waiting light does not appear or does not who the envelope. Any ideas on what is missing from this configuration to enable the light Thanks -------------------------------------------------------------------------------------------------- ! Last configuration change at 17:45:23 Central Wed Feb 5 2014 ! NVRAM config last updated at 17:47:13 Central Wed Feb 5 2014 ! version 15.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname PBX_System ! boot-start-marker boot-end-marker ! ! ! no aaa new-model memory-size iomem 20 clock timezone Central -6 0 clock summer-time DST recurring ip source-route ! ! ! no ip dhcp use vrf connected ip dhcp excluded-address 192.168.20.1 192.168.20.19 ! ip dhcp pool voip_dhcp network 192.168.20.0 255.255.255.0 dns-server 75.75.75.75 75.75.76.76 option 150 ip 192.168.20.1 default-router 192.168.20.1 ! ! ip cef no ipv6 cef multilink bundle-name authenticated ! ! ! ! trunk group main !! ! ! ! ! voice-card 0 ! ! ! license udi pid CISCO2801 sn FTX1111Z17K ! ! ! ! ! ! ! interface FastEthernet0/0 ip address 192.168.20.1 255.255.255.0 ip nat inside ip virtual-reassembly in duplex auto speed auto ! interface Service-Engine0/1 ip unnumbered FastEthernet0/0 service-module ip address 192.168.20.5 255.255.255.0 service-module ip default-gateway 192.168.20.1 ! interface FastEthernet0/1 ip address X.X.X.X 255.255.255.224 ip nat outside ip virtual-reassembly in duplex auto speed auto ! ip forward-protocol nd ! ! ip http server ip http authentication local ip http path flash: ip nat inside source list 1 interface FastEthernet0/1 overload ip route 0.0.0.0 0.0.0.0 X.X.X.X ip route 192.168.20.5 255.255.255.255 Service-Engine0/1 ! logging esm config access-list 1 permit 192.168.20.0 0.0.0.255 ! ! tftp-server flash:S00105000400.sbn tftp-server flash:P00308000800.loads tftp-server flash:P00308000800.sb2 tftp-server flash:P00308000800.sbn tftp-server flash:P00308000800.txt tftp-server flash:OS79XX.TXT tftp-server flash:cnu70.63-0-1-4.sbn tftp-server flash:Jar70.63-0-1-4.sbn tftp-server flash:jvm70.603ES1R4.sbn tftp-server flash:term70.default.loads ! control-plane ! ! ! ! voice-port 0/0/0 trunk-group main 3 timeouts call-disconnect 2 timeouts ringing infinity timeouts wait-release 5 connection plar 1051 description PSTN XXX-xXX-5353 caller-id enable ! voice-port 0/0/1 trunk-group main 2 timeouts call-disconnect 2 timeouts ringing infinity timeouts wait-release 5 connection plar 1052 description PSTN XXX-XXX-5354 caller-id enable ! voice-port 0/0/2 trunk-group main 1 timeouts call-disconnect 2 timeouts ringing infinity timeouts wait-release 5 connection plar 1053 description PSTN XXX-XXX-5355 caller-id enable ! ! ! dial-peer voice 1 pots trunkgroup main destination-pattern 412....... no digit-strip ! dial-peer voice 200 voip destination-pattern 2... b2bua session protocol sipv2 session target ipv4:192.168.20.5 dtmf-relay sip-notify codec g711ulaw no vad ! dial-peer voice 2 pots trunkgroup main destination-pattern 1.......... no digit-strip ! !! gatekeeper shutdown ! ! telephony-service max-ephones 30 max-dn 32 ip source-address 192.168.20.1 port 2000 system message My Business cnf-file location flash: load 7914 S00105000100 load 7960-7940 P00308000800 load 7970 TERM70.6-0-3SR1S time-zone 8 voicemail 2000 max-conferences 8 gain -6 moh music-on-hold.au multicast moh 239.2.2.2 port 2000 web admin system name xxxx password xxxxxxx dn-webedit time-webedit transfer-system full-consult create cnf-files version-stamp 7960 Feb 05 2014 17:42:45 ! ! ephone-dn 1 number 1001 label Room 1 description Room 1 name Room 1 call-forward busy 2000 call-forward noan 2000 timeout 10 ! ! ephone-dn 2 number 1002 label Room 2 description Room 2 name Room 2 call-forward busy 2000 call-forward noan 2000 timeout 10 ! ! ephone-dn 3 number 1003 label Room 3 description Room 3 name Room 3 call-forward busy 2000 call-forward noan 2000 timeout 10 ! ! ephone-dn 4 number 1004 label Room 4 description Room 4 name Room 4 call-forward busy 2000 call-forward noan 2000 timeout 10 ! ! ephone-dn 5 number 1010 label Recep description Recep name Recep call-forward busy 2000 call-forward noan 2000 timeout 10 ! ! ephone-dn 25 number 1051 label Main Line description Main Line name Main Line call-forward noan 2000 timeout 10 ! ! ephone-dn 26 number 1052 label Line 2 description Line 2 name Line 2 ! ! ephone-dn 27 number 1053 label Line 3 description Line 3 name Line 3 ! ! ephone-dn 30 number 6000 label Paging description Paging name Paging paging ip 239.1.1.10 port 2000 ! ! ephone-dn 31 number 8000.... mwi on ! ! ephone-dn 32 number 8001.... mwi off ! ! ephone 1 mac-address 0015.F9ED.3CDC button 1:1 ! ! ! ephone 2 mac-address 001A.2FE7.7CFA button 1:2 ! ! ! ephone 3 mac-address 001A.2FE7.79F6 button 1:3 ! ! ! ephone 4 mac-address 000F.3412.8D42 button 1:4 ! ! ! ephone 5 mac-address 0015.6389.B6FF type 7960 button 1:5 3:25 4:26 5:27 ! ! ! line con 0 line aux 0 line 130 no activation-character no exec transport preferred none transport input all transport output pad telnet rlogin lapb-ta mop udptn v120 line vty 0 4 login local transport input telnet ! scheduler allocate 20000 1000 ntp peer 192.168.20.1 ntp server 216.228.192.69 end
... View more
Labels:
02-24-2014
12:57 PM
Hello Guys, I have taken on the support of a CME with little knowledge so forgive my ignorance. We have an issue where calls are coming into the office and they ring busy. Some of the times they ring OK but caller have complained about the phone lines being busy. Below is the configuration. Thanks in advance. ! ! Last configuration change at 17:45:23 Central Wed Feb 5 2014 ! NVRAM config last updated at 17:47:13 Central Wed Feb 5 2014 ! version 15.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname PBX_System ! boot-start-marker boot-end-marker ! ! ! no aaa new-model memory-size iomem 20 clock timezone Central -6 0 clock summer-time DST recurring ip source-route ! ! ! no ip dhcp use vrf connected ip dhcp excluded-address 192.168.20.1 192.168.20.19 ! ip dhcp pool voip_dhcp network 192.168.20.0 255.255.255.0 dns-server 75.75.75.75 75.75.76.76 option 150 ip 192.168.20.1 default-router 192.168.20.1 ! ! ip cef no ipv6 cef multilink bundle-name authenticated ! ! ! ! trunk group main !! ! ! ! ! voice-card 0 ! ! ! license udi pid CISCO2801 sn FTX1111Z17K ! ! ! ! ! ! ! interface FastEthernet0/0 ip address 192.168.20.1 255.255.255.0 ip nat inside ip virtual-reassembly in duplex auto speed auto ! interface Service-Engine0/1 ip unnumbered FastEthernet0/0 service-module ip address 192.168.20.5 255.255.255.0 service-module ip default-gateway 192.168.20.1 ! interface FastEthernet0/1 ip address X.X.X.X 255.255.255.224 ip nat outside ip virtual-reassembly in duplex auto speed auto ! ip forward-protocol nd ! ! ip http server ip http authentication local ip http path flash: ip nat inside source list 1 interface FastEthernet0/1 overload ip route 0.0.0.0 0.0.0.0 X.X.X.X ip route 192.168.20.5 255.255.255.255 Service-Engine0/1 ! logging esm config access-list 1 permit 192.168.20.0 0.0.0.255 ! ! tftp-server flash:S00105000400.sbn tftp-server flash:P00308000800.loads tftp-server flash:P00308000800.sb2 tftp-server flash:P00308000800.sbn tftp-server flash:P00308000800.txt tftp-server flash:OS79XX.TXT tftp-server flash:cnu70.63-0-1-4.sbn tftp-server flash:Jar70.63-0-1-4.sbn tftp-server flash:jvm70.603ES1R4.sbn tftp-server flash:term70.default.loads ! control-plane ! ! ! ! voice-port 0/0/0 trunk-group main 3 timeouts call-disconnect 2 timeouts ringing infinity timeouts wait-release 5 connection plar 1051 description PSTN XXX-xXX-5353 caller-id enable ! voice-port 0/0/1 trunk-group main 2 timeouts call-disconnect 2 timeouts ringing infinity timeouts wait-release 5 connection plar 1052 description PSTN XXX-XXX-5354 caller-id enable ! voice-port 0/0/2 trunk-group main 1 timeouts call-disconnect 2 timeouts ringing infinity timeouts wait-release 5 connection plar 1053 description PSTN XXX-XXX-5355 caller-id enable ! ! ! dial-peer voice 1 pots trunkgroup main destination-pattern 412....... no digit-strip ! dial-peer voice 200 voip destination-pattern 2... b2bua session protocol sipv2 session target ipv4:192.168.20.5 dtmf-relay sip-notify codec g711ulaw no vad ! dial-peer voice 2 pots trunkgroup main destination-pattern 1.......... no digit-strip ! !! gatekeeper shutdown ! ! telephony-service max-ephones 30 max-dn 32 ip source-address 192.168.20.1 port 2000 system message My Business cnf-file location flash: load 7914 S00105000100 load 7960-7940 P00308000800 load 7970 TERM70.6-0-3SR1S time-zone 8 voicemail 2000 max-conferences 8 gain -6 moh music-on-hold.au multicast moh 239.2.2.2 port 2000 web admin system name root password MIL0205ncl dn-webedit time-webedit transfer-system full-consult create cnf-files version-stamp 7960 Feb 05 2014 17:42:45 ! ! ephone-dn 1 number 1001 label Room 1 description Room 1 name Room 1 call-forward busy 2000 call-forward noan 2000 timeout 10 ! ! ephone-dn 2 number 1002 label Room 2 description Room 2 name Room 2 call-forward busy 2000 call-forward noan 2000 timeout 10 ! ! ephone-dn 3 number 1003 label Room 3 description Room 3 name Room 3 call-forward busy 2000 call-forward noan 2000 timeout 10 ! ! ephone-dn 4 number 1004 label Room 4 description Room 4 name Room 4 call-forward busy 2000 call-forward noan 2000 timeout 10 ! ! ephone-dn 5 number 1010 label Recep description Recep name Recep call-forward busy 2000 call-forward noan 2000 timeout 10 ! ! ephone-dn 25 number 1051 label Main Line description Main Line name Main Line call-forward noan 2000 timeout 10 ! ! ephone-dn 26 number 1052 label Line 2 description Line 2 name Line 2 ! ! ephone-dn 27 number 1053 label Line 3 description Line 3 name Line 3 ! ! ephone-dn 30 number 6000 label Paging description Paging name Paging paging ip 239.1.1.10 port 2000 ! ! ephone-dn 31 number 8000.... mwi on ! ! ephone-dn 32 number 8001.... mwi off ! ! ephone 1 mac-address 0015.F9ED.3CDC button 1:1 ! ! ! ephone 2 mac-address 001A.2FE7.7CFA button 1:2 ! ! ! ephone 3 mac-address 001A.2FE7.79F6 button 1:3 ! ! ! ephone 4 mac-address 000F.3412.8D42 button 1:4 ! ! ! ephone 5 mac-address 0015.6389.B6FF type 7960 button 1:5 3:25 4:26 5:27 ! ! ! line con 0 line aux 0 line 130 no activation-character no exec transport preferred none transport input all transport output pad telnet rlogin lapb-ta mop udptn v120 line vty 0 4 login local transport input telnet ! scheduler allocate 20000 1000 ntp peer 192.168.20.1 ntp server 216.228.192.69 end
... View more
Labels:
02-10-2012
06:17 AM
Here is what I get on both pub and subscriber so it seems like they are replicating properly Cluster Detailed View from PUB (2 Servers): PING REPLICATION REPL. DBver& REPL. REPLICATION SETUP SERVER-NAME IP ADDRESS (msec) RPC? STATUS QUEUE TABLES LOOP? (RTMT) & details ----------- ------------ ------ ---- ----------- ----- ------------ ----------------- TBFCMPUB X.X.X.X 0.054 Yes Connected 0 match Yes (2) PUB Setup Completed TBFCMSUB1 X.X.X.Y 0.133 Yes Connected 0 match Yes (2) Setup Completed
... View more
02-10-2012
06:14 AM
gstarr thanks for the replies and on both publisher and subscriber I get the following. - Perf class (Number of Replicates Created and State of Replication) has instances and values: ReplicateCount -> Number of Replicates Created = 541 ReplicateCount -> Replicate_State = 2 Although on the RTMT I get an Alert 2 days ago for DBReplicationFailure so it seems like there is a failure but only intermittently and would this cause the phones to continue with their "old configs"?
... View more
02-10-2012
05:47 AM
Truthfully we had a consultant upgrade us from 4.1 to 6 (I believe) and then to version 8, so i am not exactly sure if he had problems with the upgrade. Is there a place that you recommend I look at to try and find a fix?
... View more
02-09-2012
02:29 PM
We recently upgraded our CallManager from 4.1 to 8.6 and we have one 7940 phone that was configured for an extension 8774 and we replaced that phone with another 7940 phone and transferred that number to the new phone. The new phone has the correct extension but so does the old phone. They both have the same extension. We deleted the phone in the CallManager but when the phone boots it comes up with the same extension and configuration. It dials and receives calls just like the "new" phone. I have 2 phones with the exact same configuration and extension but one doesn't want to let go of it and pick up the AutoRegistration numbers. I have done a factory reset but when it resets it comes up with the same config. Any ideas?
... View more
Labels:
02-23-2007
06:26 AM
We have a site that has 20 users and a "remote" site that is about 200 Meters from the central server room with a 3560 with 1 Vlans (Voice and Computers) and is cabled with 6 strands of fiber. This remote area will only have 1 phone and it seems like a expensive cost to add an 8 or 24 port switch. We thought we could connect an additional phone via the Gigabit port and use a Fiber to Ethernet converter to run a 7940 phone. We tried connecting the Gbic connector of the Catalyst to the HP Gigabit (already have so a cost savings) fiber connector but there is no link light. My thoughts are. 1. The gigabit port on the Catalyst isn't enabled? 2. The gigabit connector does not like the HP Fiber connector? 3. Will the Fiber to Ethernet work for a single phone? Hope this helps clarify our problem. Thanks
... View more
02-22-2007
08:15 AM
We are trying to connect a fiber port from a 3560 Switch to a HP ProCurve 8000 switch but I am not getting any activity on either port. I know both work when connected to the same HP manufacturer switch on both sides but I can't make them talk to each other. (Cisco to HP NO), (HP to HP YES). I am new with the Cisco switches but I figured they would work regardless of the device. Any thoughts? The fiber tests fine. Does the Cisco fiber port need to be enabled?
... View more
Labels:
02-20-2007
09:18 AM
We have Cisco Voip solution with 3560's POE Switches in our campus on 2 VLANS (Voice and Computers). We would like to add a single phone to our maintenance center but do not want to pay or need the 24 ports of the 3560's or the POE. We have a 6 Strand Fiber Connection to this site and are looking for switch recommendations for just 1 - 7940 phone with a power cube. Ideas anyone?
... View more
Labels:
11-07-2017
We recently moved to Cisco Spark for our office with Intellepeer for our
SIP provider and at times w...
03-09-2014
We have a 2801 router with CME 8.1 and CUE 3.2.3. We receive calls on 3
analog lines into a 4 port F...
03-09-2014
Manish, Thanks. I have added this command to all 3 voice ports 0/0/0 to
0/0/2 but I still have a del...
03-08-2014
I am trying to understand how FXO ports work. I have little experience
with this so I am trying to l...
03-05-2014
I made these changes but it still rings busy. Would this be something
that the carrier has to config...
02-24-2014
Hello guys, we recently took over a phone system and it has the
following problem. When someone call...
02-24-2014
Hello Guys,I have taken on the support of a CME with little knowledge so
forgive my ignorance. We ha...
02-10-2012
Here is what I get on both pub and subscriber so it seems like they are
replicating properlyCluster ...
02-10-2012
gstarr thanks for the replies and on both publisher and subscriber I get
the following. - Perf class...
02-10-2012
Truthfully we had a consultant upgrade us from 4.1 to 6 (I believe) and
then to version 8, so i am n...
02-09-2012
We recently upgraded our CallManager from 4.1 to 8.6 and we have one
7940 phone that was configured ...
02-23-2007
We have a site that has 20 users and a "remote" site that is about 200
Meters from the central serve...
02-22-2007
We are trying to connect a fiber port from a 3560 Switch to a HP
ProCurve 8000 switch but I am not g...
Public Statistics
| Date Registered | 04-24-2006 07:21 AM |
| Date Last Visited | 07-23-2018 09:57 AM |
| Total Messages Posted | 14 |
