Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Luffy
08-15-2019
Stats
Member since
03-22-2017
7
Posts
0
Helpful
0
Solutions
Created by
Luffy
in Unified Computing System Discussions
in Unified Computing System Discussions
08-11-2019
06:14 PM
08-11-2019
06:14 PM
Hi Krik J, Thank you for your answer. You mean that if all systems have same condition(network, vmotion status, vcenter etc) they can migrate from existing VM to HyperFlex. Is it correct ? Thank you,
... View more
Created by
Luffy
in Unified Computing System Discussions
in Unified Computing System Discussions
08-08-2019
01:08 AM
08-08-2019
01:08 AM
Hi, I have many hosts and they are operating into VMware vCenter server. Cisco HyperFlex system will arrive in my company soon. So I have to migrate existing VMs to Hyperflex cluster. How can I migrate ? Just thinking vMotion from existing host to hyperflex cluster node. (same network setting and same vCenter server) Does it can support ? correct ? Thank you,
... View more
Labels:
11-06-2018
09:59 PM
Hi,
I have a problem about zone merge in the MDS9148S.
In my case, I have two MDS and they set as ISL on the two MDS device.
As you know on the default status, activate zoneset only can share between two ISL device.
I'd like to merge and share all of zone databases(including sh run config) so I searched command by cisco document.
after searching, I found two commands for merging.
What is different between "zoneset distribute full vsan" and "zone copy active-zoneset full-zoneset vsan"
Q1. Can I use both of them ?
Are their commands same function ?
Q2. If I use only default mode, Switch1(save all of zone database) device is failed, Can Switch2(Only have activate zonset database) have still activate zoneset database although Switch2 don't have all of zone database ?
... View more
- Tags:
- mds
- zone merge
Labels:
05-22-2017
06:07 PM
Thank you for your answer.
2. can you ping between vlan 10 and vlan 20 interface ip addresses ok ?
-> No, It can't ping each other.
I mean only same vlan can ping each other(vlan 10 interfaces).
... View more
05-22-2017
02:30 AM
Thank you for your answer.
You mean that sup720 is not supported ip rouing command, right ?
I'll test tomorrow about options.
Line card is "WS-X6748-GE-TX"
The vlan interface is also up/up and ping is also working well in same vlans.
... View more
05-22-2017
01:56 AM
Hi guys,
This is KJ.
I'd like to get a helping hand from you.
How can I set L3 mode on C6500 switch ?
Actually, I tested vlans using C6509.
There are a Line card and a supervisor in C6509.
2 vlans(vlan 10 and vlan 20) set in a line card(Port 1-10 vlan 10, Port 11-20 vlan 20)
vlans can't communicate each other because C6509 is L2 mode now.
I'll use supervisor interface port as wan port.
In case of C3650 or C3850 switches, "ip routing" command can transfer L3 mode switch.
And also vlan 10 and 20 can communicate with each other because C3650 or C3850 is L3 switch.
But In case of C6509, "ip routing" command is not supported.
So, still vlan 10 and 20 can't communicate now.
How can I configure L3 mode in C6509 ?
Have a nice day
... View more
Labels:
Created by
Luffy
in Unified Computing System Discussions
08-11-2019
08-11-2019
Hi Krik J,Thank you for your answer. You mean that if all systems have
same condition(network, vmoti...
Created by
Luffy
in Unified Computing System Discussions
08-08-2019
08-08-2019
Hi, I have many hosts and they are operating into VMware vCenter
server.Cisco HyperFlex system will ...
11-06-2018
Hi, I have a problem about zone merge in the MDS9148S. In my case, I
have two MDS and they set as IS...
05-22-2017
Thank you for your answer. 2. can you ping between vlan 10 and vlan 20
interface ip addresses ok ? -...
05-22-2017
Thank you for your answer. You mean that sup720 is not supported ip
rouing command, right ? I'll tes...
Public Statistics
| Date Registered | 03-22-2017 08:54 PM |
| Date Last Visited | 08-15-2019 11:36 PM |
| Total Messages Posted | 7 |
