About DazOG

DazOG · 05-24-2024

HiHoping someone can help. I recently purchased a NIM-VAB-A card to go in our ISR4451, with the goal of eliminating an ISP's insecure unmanaged router. I have configured this following various guides online, and it is working from a connectivity po...

DazOG · 01-15-2024

HiI have a 3750-X switch that has some PoE cameras and a controller attached. I'm trying to make it so that the cameras are only powered when the controller is, because one isn't used without the other. I have written two event applets that simply ...

DazOG · 11-28-2023

HiI have a working "ip sla" setup, following the instructions here: https://www.cisco.com/c/en/us/support/docs/ip/ip-routing/200785-ISP-Failover-with-default-routes-using-I.html and elsewhere.The problem I've got is that in the example above the test...

DazOG · 11-27-2023

HiI've got a working ZBFW config, but I must admit I'm struggling to understand the differences between these commands:policy-map type inspect NAMEpolicy-map NAMEclass-map type inspect NAMEclass-map NAMECisco's documentation says:When an inspect-type...

DazOG · 11-23-2023

HiI’m migrating from a CBAC based basic firewall configuration on a 800 series router to an ISR, and am trying to get ZBFW working. I’m obviously doing something wrong because nothing works What I’m basically trying to achieve is to allow everyone...

DazOG · 05-24-2024

Thanks.As far as the ZBFW config goes, I already have an internal VLAN that has zone-member security INSIDE on, with associated pairings, etc. This all works ok. I've seen some configs put the zone-member security INSIDE on the Ethernet0/2/0.101 su...

DazOG · 01-16-2024

Tested my script this morning, seems to work correctly. Log shows as follows:Jan 16 10:05:46.524: %LINK-3-UPDOWN: Interface GigabitEthernet2/0/3, changed state to upJan 16 10:05:47.530: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet...

DazOG · 01-15-2024

I'll try your one tomorrow @Dan Frey - I really like how it's a "one size fits all" applet to handle both states. 

DazOG · 01-15-2024

Incredible, thanks! That's great. That looks much more elegant than what i came up with!This is what I managed - untested - but the idea was that the "down" script would only be created when the "up" script had run, and that the "up" script would o...

DazOG · 01-15-2024

Thanks.20 seconds is more than enough time for the scripts to run.I don't know if I am being clear enough. When the controller device comes online, I see the following in my syslog:Jan 15 10:56:07.258: %LINK-3-UPDOWN: Interface GigabitEthernet2/0/3,...

Member Since	‎11-07-2023 08:04 AM
Date Last Visited	‎06-06-2024 07:00 AM
Posts	30
Total Helpful Votes Received	6

User Statistics

User Activity

Help with relationship wrt Ethernet & Dialer interfaces in VDSL config

EEM - wait until interface fully up before processing?

Failover ISP setup - can't ping Internet from standby interface

"policy-map type inspect XX" vs "policy-map XX", etc

First time ZBFW config - can’t access anything

Re: Help with relationship wrt Ethernet & Dialer interfaces in VDS

Re: EEM - wait until interface fully up before processing?

Re: EEM - wait until interface fully up before processing?

Re: EEM - wait until interface fully up before processing?

Re: EEM - wait until interface fully up before processing?