yes path correct make .x (required version to upgrade), we are not sure what is connected to Nexus 5K, if FEX connected have a look release notes, also if this Nexus connected in flexpod - read the release notes.   if no special devices connected it is standard switch then it is good to go as mentioned steps.   read the release notes before upgrading.   https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5500/sw/upgrade/731_N1_1/n5500_upgrade_downgrade_731_n1_1.html#pgfId-773813 ... View more

i believe you can use EEM Script for this  based on the logs.   https://community.cisco.com/t5/networking-documents/cisco-eem-basic-overview-and-sample-configurations/ta-p/3148479     ... View more

Look for basic configuration :   https://support.solarwinds.com/Success_Center/Netflow_Traffic_Analyzer_(NTA)/Knowledgebase_Articles/NetFlow_ISR_4300_Series_Router_sample_configuration   use tool for netflow collector.   https://www.cisco.com/c/en/us/products/ios-nx-os-software/ios-netflow/networking_solutions_products_genericcontent0900aecd805ff72b.html   ... View more

If i understand your question correctly.   you are migrationg Cat 6500s to a pair of Nexus 7700s ( so you looking like a like migration) and decommission 6500 is this correct. if not do not go to next steps and explain more.   T here are different approaches you can do here is : (easy one is)   1. you need to have L3 interface and point to point interface configured and  in shutdown mode 2. example 6500 VLAN 10 - same will be created in nexus and p2p ip configured 3. once you ready for cutover, 6500 VLAN 10 shutdown, and point to point interface , bring up VLAN 10 and p2p interface in nexus 4. Move the down stream switch link to Nexus and test it. ospf/eigrp neighbourship.       ... View more

Look at netflow, it will give you more granular information what you looking for.   https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/netflow/configuration/xe-16/nf-xe-16-book/nflow-filt-samp-traff-xe.html https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/netflow/configuration/xe-16/nf-xe-16-book/cfg-nflow-data-expt-xe.html   ... View more

In general suggestion(with out looking what is your config and setup)   1. i look to fix the issue, why this is keep going shutdown mode and suspended mode. find the reason the fix it, if not remove from Port-channel. 2. what is the error message you getting while shutdown and suspended state.   provide some information so we can understand the issue for better suggestion    ... View more

This example : you can do same for all VLAN and test and advice.   Destination address :  192.168.1.65  subnet sk MASK 255.255.225.192 gateway :  192.168.1.6 ( as per your information the router IP)   ... View more

here is the place to start :   https://www.cisco.com/c/en/us/solutions/collateral/enterprise-networks/trustsec/solution-overview-c22-737173.html   https://www.cisco.com/c/en/us/solutions/enterprise-networks/trustsec/index.html#~stickynav=1   ... View more

Look at the profile editor settings :   https://www.cisco.com/c/en/us/td/docs/security/vpn_client/anyconnect/anyconnect41/administration/guide/b_AnyConnect_Administrator_Guide_4-1/anyconnect-profile-editor.html ... View more

yes afaik it should be ok to do that.   Refer :   https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/eem/command/eem-cr-book/eem-cr-a1.html https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/eem/configuration/12-4t/eem-12-4t-book/eem-policy-cli.pdf ... View more

This question not have basic question and  clarity here. you need to provide more information.   what is the device you having issue, what URL is that, what is the error you getting.   I would be nice to have more information about your setup and devices in the network to provide best suggestion or solution to fix.   ... View more

As per notes from community  :   To associate your AnyConnect Client Licence to your RV345 you must generate a Token from your Smart Account. Then go to your RV345 GUI -> Administration -> Licence -> Click on Register, and there you paste the Token generated. This is the way you associate the Licence with the RV. About the AnyConnect Software, you must call Enterprise TAC +1 800 553 2447. They must associate your Service Contract (Licence) with your Cisco Smart Account. They you go to Downloads, search for AnyConnect and click on Download.   here is the link for reference :   https://www.cisco.com/c/dam/en/us/td/docs/routers/csbr/RV340/Quick_Start_Smart_License/Smart_License_qsg_en_V4.pdf   ... View more