Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About averill.johnson1
Stats
Member since
03-16-2016
11
Posts
0
Helpful
1
Solution
Created by
averill.johnson
in Other Network Architecture Subjects
in Other Network Architecture Subjects
06-11-2019
08:47 AM
06-11-2019
08:47 AM
It's running windows 10. I can tftp the config over to it manually. The job works for about a week then it dies out. I have a weeks worth of configs and then nothing. A few caveats, the destination is virtual but there is definitely a path as I can ssh no problem. I can tftp the config also no issues there. Do you have any other ideas, anything outside the box that I could try?
... View more
Created by
averill.johnson
in Other Network Architecture Subjects
06-10-2019
02:16 PM
06-10-2019
02:16 PM
I figured it was close to right, and I agree that by it showing inactive it is going to run on specified date / time. My confusion comes in that I don't have any backups to show on my tftp server.
... View more
Created by
averill.johnson
in Other Network Architecture Subjects
06-06-2019
08:43 AM
06-06-2019
08:43 AM
Setup kron jobs to backup / redirect configs on specific days: sh run | s kron kron occurrence friday_backup at 22:30 Fri recurring policy-list friday_backup kron policy-list friday_backup cli show running-config | redirect tftp://192.168.XX.XXX/$h-$t_running_friday_config cli show startup-config | redirect tftp://192.168.XX.XXX/$h-$t_startup_friday_config show kron schedule friday_backup inactive, will run again in 1 day 08:49.16 at 22:30 on Fri Any ideas on the inactive status when I have the recurring command?
... View more
Labels:
06-04-2019
07:34 AM
I have been doing a bit of research on this and haven't found anything definitive on this but I feel it should work. Can anyone confirm or deny? Equipment: Virtual: ISE 2.4 Cisco 3850 Stack(s) IOS 3.6.9E RADIUS Authentication works perfectly. Any assistance would be greatly appreciated.
... View more
Created by
averill.johnson
in Intrusion Prevention and Detection Systems (IPS - IDS)
05-24-2019
06:35 AM
05-24-2019
06:35 AM
Yeah after performing the shutdown command on the other modules it was able to uninstall successfully. I was messing with a spare and I just wanted to put it back the way I found it.
... View more
Created by
averill.johnson
in Intrusion Prevention and Detection Systems (IPS - IDS)
05-23-2019
12:13 PM
05-23-2019
12:13 PM
I am working with a spare ASA 5512X. I had two modules installed previously, IPS and CXSC and the device worked (even though all modules were unresponsive). When I enter the command sw-module module ips recovery configure image flash:/<path> I get error recovery in use by module sfr (or something similar). How do I take the line out of the sfr module recovery so that I can run the IPS recovery?
... View more
Labels:
12-05-2017
04:24 PM
Yes, that is correct. Just to ensure my understanding, would this work if it would only be a temporary thing? This (PBR) would be used for a brief period of time then reverted so traffic would be routed normally (within same subnet).
... View more
12-05-2017
03:58 PM
What is the best way to stop and re-route traffic across OSPF enabled devices?
A server (SrvA) is connected a router (RtrA) running OSPF (Area 1) connected to a switch (SwA) which is connected via OSPF (Area0) to a different switch (SwB) running OSPF (Area 2) to a router (RtrB) which is connected to a server (SrvB)
SrvA = 192.168.10.100/24
SrvB = 192.168.20.100/24
SwA = 192.168.10.1/24 (Area1) | 192.168.1.1/30 (Area0)
SwB = 192.168.20.1/24 (Area2) | 192.168.1.2/30 (Area0)
RtrA = 192.168.10.50/24
RtrB = 192.168.20.50/24
(Other pc's on each subnet connected to respective switch.)
A pc with the ip address of 192.168.10.189 destined for 192.168.10.100 (SrvA) needs to be re-routed and sent to 192.168.20.100 (SrvB) with the least amount of interaction.
If it helps switches are 3650's (16.3) and routers are 2901's (15.3).
... View more
Labels:
Created by
averill.johnson1
in Other Network Architecture Subjects
06-11-2019
06-11-2019
It's running windows 10. I can tftp the config over to it manually. The
job works for about a week t...
Created by
averill.johnson1
in Other Network Architecture Subjects
06-10-2019
06-10-2019
I figured it was close to right, and I agree that by it showing inactive
it is going to run on speci...
06-06-2019
Setup kron jobs to backup / redirect configs on specific days: sh run |
s kronkron occurrence friday...
06-04-2019
I have been doing a bit of research on this and haven't found anything
definitive on this but I feel...
05-24-2019
Yeah after performing the shutdown command on the other modules it was
able to uninstall successfull...
05-23-2019
I am working with a spare ASA 5512X. I had two modules installed
previously, IPS and CXSC and the de...
05-22-2019
Thanks for shedding some light on that. On my 5512X I can connect to the
sfr console, which I though...
05-22-2019
Okay so if I understand correctly, if you have an FMC that you can
access you won't be able to acces...
12-05-2017
Yes, that is correct. Just to ensure my understanding, would this work
if it would only be a tempora...
Public Statistics
| Date Registered | 03-16-2016 06:52 PM |
| Date Last Visited | 06-18-2019 08:48 AM |
| Total Messages Posted | 11 |
.jpg "Hall of Fame Guru"){kind=icon}
