About afrazer

afrazer · 06-11-2025

Hi, I have ~150 sites, of varying sizes, currnetly running ipv4 only. They are connected to a variety of ISP's. I have largely compelted implemetning Ipv6 in my public cloud, and i have an allocation of Ipv6 address's from APNIC, that i can use...

afrazer · 05-09-2025

First as background, I have a meraki network, where i have multiple 'very' remote sites, where my sites are connected via Starlink, which means i do not get a fixed IP address, and the address i have is CGNAT. My remote sites are spokes, (mx68) an...

afrazer · 04-15-2025

I have an MX450 located in a remote datacenter, that was configured with a static IP address on its WAN, that i want to change to DHCP. This MX450 is NOT in production yet, so a hit on availability is not an issue.Last night, i connected to it, v...

afrazer · 04-10-2025

Hi..I have a situation where I have ~200 networks connected back to 2 hubs.. It all works fine. I have some edge case situations where i want to connect, a few sites together directly, so the traffic does not flow via my hub... ( it means i'...

Using Switch Port Profiles via the API. · 03-06-2025

So, i have figureed out how to create a switchPortProfile ( and delete it ). However, now i'm trying to figure out how you apply this profile to a port... Which api provides that?def switchPortProfile(api_key: str, request_type, action, PhysicalRe...

afrazer · 06-13-2025

"IPv6 full-tunnel support is not implemented at this time due to technical limitations. Hence, disable VPN mode for IPv6 enabled VLANs or disable IPv6 for VLANs which you wish to use IPv4 full-tunnel."What does "full-tunnel' mean?

afrazer · 05-11-2025

Some good ideas there Phillip. I have a very capable router ( 8500-12X ) and i could run ipsec vpns off there, however That router is right out on the edge and i dont' want to be sending unencrypted data to it. Putting the small appliance on the ot...

afrazer · 05-11-2025

Port forwarding works, and so does forwarding my traffic from the merkai vpn to my local servers and to up to cloud. ( connectiions off the router in the diagram ). The only thing i can't make work, is trying to get a vpn up to a non meraki vpn.

afrazer · 05-10-2025

No the device is not in one armed mode. Yes, only one port ( Wan1 ) is connected. running in one armed mode, means that Port Forwarding, and several other important and useful features no longer available.

afrazer · 05-09-2025

The ipsec tunnel needs to be created between my MX450 and the non meraki Peer, in someone elses network. The traffic of interest comes from the server shown in the diagram, going to the other server behind the non merkai peer. When i do a packet capt...

Member Since	‎10-30-2024 03:57 AM
Date Last Visited	‎12-10-2024 12:11 AM
Posts	30
Total Helpful Votes Received	8

User Statistics

User Activity

Ipv6 / Dual Stack Strategy for Remote Sites.

IPsec Tunnels not establishing to Non Meraki Peers.

Changing from Static WAN configuration TO DHCP, ( Remotely ) ( on MX450 )

Site 2 Site Connection, along side Hub connections.

Using Switch Port Profiles via the API.

Re: Ipv6 / Dual Stack Strategy for Remote Sites.

Re: IPsec Tunnels not establishing to Non Meraki Peers.

Re: IPsec Tunnels not establishing to Non Meraki Peers.

Re: IPsec Tunnels not establishing to Non Meraki Peers.

Re: IPsec Tunnels not establishing to Non Meraki Peers.