Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About youssef.el.fathi
Stats
Member since
05-13-2010
11
Posts
0
Helpful
1
Solution
02-21-2011
01:26 PM
Hello, AFAIK only the 6509-V-E does not support the legacy SUPervisor modules like 1A and 2. So you will have no problem with this configuration 6509-E + Sup2. HTH
... View more
02-15-2011
05:46 AM
Alex, For the reloading part, check the config-register. And about your ethernet check the speed/duplex or try another ethernet cable or another interface on your router. HTH
... View more
Created by
youssef.el.fath
in Routing
in Routing
01-25-2011
05:42 AM
01-25-2011
05:42 AM
You're welcome !!!
... View more
Created by
youssef.el.fath
in Routing
01-25-2011
12:07 AM
01-25-2011
12:07 AM
Hello, what type of authentication do you use : local or aaa ? Maybe it is an AAA authentication problem, because the SSH configuration seems OK for me. Youssef P.S : try to connect from another terminal or from a router.
... View more
Created by
youssef.el.fath
in Routing
12-23-2010
12:16 PM
12-23-2010
12:16 PM
Hello, you can use leak-map : http://goo.gl/JMhcF HTH
... View more
Created by
youssef.el.fath
in VPN and AnyConnect
05-20-2010
05:05 AM
05-20-2010
05:05 AM
Thanks, In summary, as i have two ISPs for the HUBs, i need two tunnels for each HUB, acting as NHRP Servers. But for the spokes, i will have four static tunnels that will learn IP addresses from the previous NHRP servers. Finally we have four subnets IP matching my four DMVPN clouds.
... View more
Created by
youssef.el.fath
in VPN and AnyConnect
05-20-2010
02:46 AM
05-20-2010
02:46 AM
Hello Andrew, My question is about design. If i go with two routers with HSRP and each one attached to each ISP, i will have to build, for a spoke, 4 multipoint GRE tunnels on each router. I attached a sample design for the clarity. Is this design correct, easy to implement or i can do it another way? Thanks. PS : as stated in the first post, the goal is redundancy of equipment and WAN Access with spoke-to-spoke "direct communication".
... View more
Created by
youssef.el.fath
in VPN and AnyConnect
05-19-2010
08:51 AM
05-19-2010
08:51 AM
Hello, I am working on my first DMVPN project and i would like to have some expert advices. Here is the topology: Two Hubs (one in France with Dual ISPs and the other in the US with one ISP for now) and many spokes (60 with two ISPs). Some spokes have to communicate each other directly and access some resources to the US and France Hub. The Hubs have to communicate directly as well. I read the DMVPN Design guide, but it is oriented towards Dual VPN with single ISP and i would like some help to point me to the right direction. Many thanks. Youssef
... View more
Labels:
02-21-2011
Hello,AFAIK only the 6509-V-E does not support the legacy SUPervisor
modules like 1A and 2. So you w...
02-15-2011
Alex,For the reloading part, check the config-register. And about your
ethernet check the speed/dupl...
01-25-2011
Hello, what type of authentication do you use : local or aaa ? Maybe it
is an AAA authentication pro...
Created by
youssef.el.fathi
in Routing
12-23-2010
12-23-2010
Hello, you can use leak-map :http://goo.gl/JMhcFHTH
Created by
youssef.el.fathi
in VPN and AnyConnect
05-20-2010
05-20-2010
Thanks,In summary, as i have two ISPs for the HUBs, i need two tunnels
for each HUB, acting as NHRP ...
Created by
youssef.el.fathi
in VPN and AnyConnect
05-20-2010
05-20-2010
Hello Andrew,My question is about design.If i go with two routers with
HSRP and each one attached to...
Created by
youssef.el.fathi
in VPN and AnyConnect
05-19-2010
05-19-2010
Hello, I am working on my first DMVPN project and i would like to have
some expert advices.Here is t...
Public Statistics
| Date Registered | 05-13-2010 10:11 AM |
| Date Last Visited | 10-09-2017 12:40 PM |
| Total Messages Posted | 11 |
