About Cap-24

Cap-24 · 01-14-2026

Trying to figure out the best way to set up a Cisco 3802E AP for our WLC environment. I was able to connect it to our WLC, but then noticed no Bridge/mesh option in WLC settings. Would be using this AP indoors, with external antenna above structure ...

Cap-24 · 12-08-2025

I have a MAP AP that connects to a RAP AP through Wireless Backhaul and then to the WLC. I am trying to figure out what switchport, WLC, AP settings need to be in place to connect local network clients to a switch connecting to the Mesh AP. All RAP...

Cap-24 · 11-26-2025

We have a control system where I work that has a Cisco 5508 WLC, Cisco Air-Cap1552E Lightweight AP's, Cisco/GarretCom switches, Nexus Meters. Each building is linked together via Fiber, Copper or AP back to the main hub. The Meter's that are online...

Cap-24 · 09-28-2025

I am trying to connect a replacement Cisco Air-Cap-1552E that I am trying to connect to our WLC5508. . It says required image not found on AP, downloading image from controller. It looks like the device is stuck in a downloading software and reboot...

Cap-24 · 09-04-2025

I am trying to reset a Cisco Air Cap 1552 E access point back to it's factory defaults. I have tried every mode button press and release from what I read online, but nothing is working. I do not have an option to reset it via a controller. Can som...

Cap-24 · 01-17-2026

@pieterh - Thanks for the reply. when I type in AP-type ? It gives me either mobility express or capwap made. Is WGB mode not supported on this 3802e AP? When I connect it to our WLC I really only have local or flex connect mode. I am looking for t...

Cap-24 · 12-17-2025

@pieterh - you were a big help and appreciate your help. I did go back and change mesh mode to Bridge. Everything else stayed the same and is working now. Hope this post helps other people with same issue.

Cap-24 · 12-16-2025

@pieterh - I think I have finally resolved this issue. I made some changes and hopefully it did not break anything else in our working set up. Let me go over what I did below.1. flex+Bridge mode enabled. Not sure if this was absolutely needed, but...

Cap-24 · 12-16-2025

I finally have access to the WLC GUI which should help. When I try and change the Vlan mode and ID under Mesh AP, Gigabitethernet0 I keep getting the error message " Failed because vlan trunking is disabled in the AP. The commands you wanted me to ...

Cap-24 · 12-15-2025

@pieterh - So why don't we start with me clearing "station-role root" line from the MAP? We can see if this resolves the issue. So is station root-role just for RAP AP configurations? From what I can tell our Cisco standalone 1602's and RAP con...

Member Since	‎07-24-2025 05:57 PM
Date Last Visited	‎01-17-2026 10:23 AM
Posts	63
Total Helpful Votes Received	10

User Statistics

User Activity

Best Set Up for Cisco 3802e AP with our current WLC Network!

Mesh AP wired backhaul to connect switch for local clients!

Ethernet Bridging setting on MAP/RAP AP's!

Required image not found on AP downloading image from controller Loop!

Resetting a Cisco Air Cap 1552E access point to factory defaults!

Re: Best Set Up for Cisco 3802e AP with our current WLC Network!

Re: Mesh AP wired backhaul to connect switch for local clients!

Re: Mesh AP wired backhaul to connect switch for local clients!

Re: Mesh AP wired backhaul to connect switch for local clients!

Re: Mesh AP wired backhaul to connect switch for local clients!