About matthewng

matthewng · 02-15-2017

Wondering if anyone done anything similar? Is it supported ? Having an issue trying to stand up a PWHE on IOS XR to Juniper (L2circuit). So LDP sessions has been established between the two PE and is UP but I am not able to get the VC up. Here are...

matthewng · 12-01-2016

Hi there I need to failover to our standby RSP-4G on our 9k due to cisco wanting to RMA our current Active RSP. Is it a hitless operation when I do a switchover? so no impact / loss of traffic? Once the RSP has been switched over, I can eject the ex...

matthewng · 11-06-2016

I have about 14 SMU that I need to activate on my ASR9010 (XR 5.3.3) due to a on going memory leak issue. About 4-5 of them is a reboot SMU while rest is hitless Just want to know, can I activate all 14 SMU in one go with one one reboot? If so, what ...

matthewng · 07-11-2016

Hi there, we currently have a ASR9K with 5.2.2 + SP and want to know do we need to deactivate the 5.2.2 SP1 first before activating the 5.3.3 Pies? Active Packages: disk0:asr9k-doc-px-5.2.2 disk0:asr9k-k9sec-px-5.2.2 disk0:asr9k-mini-px-5.2.2 disk0...

matthewng · 05-17-2016

Hi Guys, I have a ASR9010 with IOS XR 5.2.2 and we are wanting to upgrade it to 5.3.3. This is my first time doing this. Due to limited disk space, its not enough to store 2 IOS XR, so I want to know what files are safe to delete in order to free up...

matthewng · 12-01-2016

Thank you Standby RSP is ready (see output below) Is there any documentation from cisco about the manual switchover being hitless? as I could not find it anywhere Also BGP have NSR enabled but our IGP (OSPF) have NSR disable Will that cause any issu...

matthewng · 11-06-2016

Hi Jawai, Thank you. So will i be able to something like "install activate *asr9k-px-5.3.3.CSC*" to activate them? Matthew

matthewng · 05-18-2016

Hi Santosh, I tried to turboboot a lab 9k from 4.2.3 to 5.2.2 and everything is working ok. But the standby RSP is currently stuck in IOS XR PREP state? Is that normal? Been like this for around 30-45 minutes already Tried to console in and have the...

matthewng · 05-17-2016

Thank you for the response. I think i will go with the deactivating and removing the 5.2.2 fpd-px route and upgrade to 5.3.3 fpd manually as repartitioning disk seems to have a lot of risk involve.

matthewng · 05-17-2016

Hi Santosh, Thank you, I think I know what to do now. Just one last question, with regards to deactivating the running 5.2.2 FPD PX mentioned from the above link. So if I deactivate the 5.2.2 fpd px and remove the file which means i would have enou...

Member Since	‎05-17-2016 02:04 PM
Date Last Visited	‎10-09-2019 04:06 PM
Posts	11

User Statistics

User Activity

Inter-as VC between Juniper and Cisco ios xr (PWHE on cisco)

ASR9010 XR RSP manual switchover

Activating Multiple SMU at once (XR 5.3.3)

IOS XR 5.2.2 with SP1 upgrade to 5.3.3

IOS XR upgrade on A9K-RSP-4G

Thank you

Hi Jawai,

Hi Santosh,

Thank you for the response.

Hi Santosh,