About jamesmpoplar

jamesmpoplar · 02-07-2008

Say I have a setup like this:cluster enable core 0cluster member 1 mac-address 0011.2196.d800 vlan 303cluster member 2 mac-address 0011.5cc2.b500 vlan 303cluster member 3 mac-address 0011.9247.b500 vlan 303And the second cluster member switch dies an...

jamesmpoplar · 01-28-2008

Hello All,I was wondering what software everyone uses to collect netflow data when the server running is Linux based.I currently use MRTG for simple mass network metrics, but I'm looking to use netflow data so figure out per protocl usage.

jamesmpoplar · 12-12-2007

We have a pretty solid setup for our wireless, with a wlan dedicated to LXE MX7 scan guns who use WPA Shared keys as their way of "connecting".The first demo we used of the MX7 worked without an issue, the newer demo of the same version of scanner gu...

jamesmpoplar · 11-02-2007

Currently we are running some scan guns on the floor, a new model is running with no issue and the MAC doesn't show up in the logs.For the older scan guns I am seeing the following messages in the WLC 4402 logs:Fri Nov 2 08:13:04 2007 [SECURITY] 1x...

jamesmpoplar · 10-03-2007

When implementing DHCP snooping on 2960 switches, if the switch sits "in the middle" of two other switches, such as there is an edge switch which is trunked to a middle switch that is finally trunked to another switch, do I have to set the two trunke...

jamesmpoplar · 01-25-2008

Exactly. Talking with some of the local engineers here I have gotten some more specific information which I will forward to you off list.At this point it sounds like you should be able to just "plug and play".

jamesmpoplar · 01-25-2008

A configuration that may help was already commented below, but to expound on it the following may be helpful.Cisco switches allow you to have multiple vlans, the configuration of it would look like the following if you did a show running command:Int...

jamesmpoplar · 12-13-2007

Oh, I was just asking to see what others experiences were with the guns in question. It turns out that an aggressive power saving mode on the guns made them less likely to stay connected...changing the power saving mode to never go idle and to keep ...

jamesmpoplar · 09-17-2007

Ha!The problem was that the version on the tftp server was actually a different version of IOS, but renamed funny when it was sftped to the tftp server.Therefor it would verify just fine. :) Works fine now. Thanks for all the possible solutions.

jamesmpoplar · 09-17-2007

Well, dir flash: shows them both:32514048 bytes total (20805632 bytes free)PASASW0007#dir flash:Directory of flash:/ 2 -rwx 1216 Feb 28 1993 17:01:07 -07:00 vlan.dat 3 -rwx 27 Sep 17 2007 11:08:05 -06:00 private-config.tex...

Member Since	‎06-19-2007 02:26 PM
Date Last Visited	‎08-18-2017 03:56 AM
Posts	19
Total Helpful Votes Received	3

User Statistics

User Activity

Replacing a cluster member in a 3750 stack.

Netflow Linux Setup

Lxe Mx7 scanners with WLC question.

Strange messages in logs.

DCHP Snooping across multiple trunked switches.

Re: Routing CobraNet through a 3750 switch

Re: Routing CobraNet through a 3750 switch

Re: Lxe Mx7 scanners with WLC question.

Re: WS-C2960G-24TC-L IOS question.

Re: WS-C2960G-24TC-L IOS question.