Hi：    In the FWSM，the version is 4.1(7)，some static identidy NAT ，We need to delete； But We can't find the command：   FWSM/contextA(config)# no static (inside,outside)   ? configure mode commands/options:   interface  Global address overload from interface   tcp        TCP to be used as transport protocol   udp        UDP to be used as transport protocol FWSM/contextA(config)# no static (inside,outside)      In the other Firewall，like PIX and  ASA，We can do。  We need help！ Thanks! ... View more

We have a C6509，have a WS-X6748-SFP，show power，Oper State：off (not supported)：     NJ-GL-ASW-2.YPT.C6509# show power system power redundancy mode = redundant system power total =     2771.16 Watts (65.98 Amps @ 42V) system power used =      1590.54 Watts (37.87 Amps @ 42V) system power available = 1180.62 Watts (28.11 Amps @ 42V)                         Power-Capacity PS-Fan Output Oper PS   Type               Watts   A @42V Status Status State ---- ------------------ ------- ------ ------ ------ ----- 1    WS-CAC-3000W       2771.16 65.98  OK     OK     on  2    WS-CAC-3000W       2771.16 65.98  OK     OK     on                          Pwr-Allocated  Oper Fan  Type               Watts   A @42V State ---- ------------------ ------- ------ ----- 1    WS-C6509-E-FAN      150.36  3.58  OK                         Pwr-Requested  Pwr-Allocated  Admin Oper Slot Card-Type          Watts   A @42V Watts   A @42V State State ---- ------------------ ------- ------ ------- ------ ----- ----- 1    WS-X6748-SFP        254.94  6.07     -     -     on    off (not supported) 2    WS-X6748-SFP        254.94  6.07   254.94  6.07  on    on 5    WS-SUP720-3B        282.24  6.72   282.24  6.72  on    on 6    WS-SUP720-3B        282.24  6.72   282.24  6.72  on    on 8    WS-X6704-10GE       295.26  7.03   295.26  7.03  on    on 9    WS-X6748-GE-TX      325.50  7.75   325.50  7.75  on    on system auxiliary power mode = off system auxiliary power redundancy operationally = non-redundant system primary connector power limit =   10920.00 Watts (260.00 Amps @ 42V) system auxiliary connector power limit = 10500.00 Watts (250.00 Amps @ 42V) system primary power used =              1590.54 Watts (37.87 Amps @ 42V) system auxiliary power used =            0 Watt NJ-GL-ASW-2.YPT.C6509#   But，When We show module ，it is OK：   NJ-GL-ASW-2.YPT.C6509#   show module Mod Ports Card Type                              Model              Serial No. --- ----- -------------------------------------- ------------------ -----------   1   48  CEF720 48 port 1000mb SFP              WS-X6748-SFP       SAL1424KCY0   2   48  CEF720 48 port 1000mb SFP              WS-X6748-SFP       SAL16148SUZ   5    2  Supervisor Engine 720 (Hot)            WS-SUP720-3B       SAL100194GS   6    2  Supervisor Engine 720 (Active)         WS-SUP720-3B       SAL14049C6D   8    4  CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE      SAL1629HCC7   9   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     SAL1532LR5U Mod MAC addresses                       Hw    Fw           Sw           Status --- ---------------------------------- ------ ------------ ------------ -------   1  5475.d031.ab14 to 5475.d031.ab43   2.3   12.2(18r)S1  12.2(33)SXI3 Ok   2  f0f7.55a1.e83c to f0f7.55a1.e86b   2.4   12.2(18r)S1  12.2(33)SXI3 Ok   5  0014.a97e.4e9c to 0014.a97e.4e9f   4.7   8.5(4)       12.2(33)SXI3 Ok   6  001f.6c77.b080 to 001f.6c77.b083   5.9   8.5(3)       12.2(33)SXI3 Ok   8  a493.4c1f.d6d0 to a493.4c1f.d6d3   3.2   12.2(14r)S5  12.2(33)SXI3 Ok   9  30e4.dbf0.7d30 to 30e4.dbf0.7d5f   4.1   12.2(18r)S1  12.2(33)SXI3 Ok Mod  Sub-Module                  Model              Serial       Hw     Status  ---- --------------------------- ------------------ ----------- ------- -------   1  Centralized Forwarding Card WS-F6700-CFC       SAL1426LS8P  4.1    Ok   2  Centralized Forwarding Card WS-F6700-CFC       SAL16127Y8W  4.1    Ok   5  Policy Feature Card 3       WS-F6K-PFC3B       SAL10019BSE  2.7    Ok   5  MSFC3 Daughterboard         WS-SUP720          SAL10019AB9  2.11   Ok   6  Policy Feature Card 3       WS-F6K-PFC3B       SAL140399Y5  2.6    Ok   6  MSFC3 Daughterboard         WS-SUP720          SAL14049B7Y  4.0    Ok   8  Centralized Forwarding Card WS-F6700-CFC       SAL1628GJ86  4.1    Ok   9  Centralized Forwarding Card WS-F6700-CFC       SAL1532M0YP  4.1    Ok Mod  Online Diag Status  ---- -------------------   1  Pass   2  Pass   5  Pass   6  Pass   8  Pass   9  Pass NJ-GL-ASW-2.YPT.C6509#   What should we do? ... View more

Hi,      We have  NX5596up， we config the snmpv2，output：   NJ-GL-ASW-2.YPT.N5K(config)# username asiainfo_yunwei role vdc-operator  warning: unable to update SNMP users database reason: group not found   NJ-GL-ASW-2.YPT.N5K(config)# username admin role vdc-admin  warning: unable to update SNMP users database reason: group not found     We need to help, thank you！ ... View more

Sorry,  We encountered a problem , The C4900M  WS-X4908-10G-RJ45 , interface Te, when we shutdown it, and wait a moment ,we no shutdown it, it display noconnected state;now ,the port led is not trun on, later,it display inactive state; later,and we wait for 30 s maybe,it can up！ we had upgrade the IOS,but the problem  not to slove! we are very anxious, please help us ,thank you! ... View more