About jakidaslomoro

jakidaslomoro · 10-09-2020

Dear all, I have an AP AIR-AP1572EAC and wanted to reset to default but all times I try to reset it, it competely does not get to the default. I unplug the power cable and press the reset buton and connect the Power cable back, and the LEDs would tur...

jakidaslomoro · 08-02-2020

I am confuring a new wireless Bridge. I have already configured one of the AP as the root bridge but when Configuring the second one to be non-root, the dot11radio was in root so then I changed it to non-root bridge. When I checked the radio inter...

jakidaslomoro · 07-31-2020

I am configuring a wireless Bridge on the AP AIR-AP1572EAC-E-K9. When I, set the role to non-root on Radio and enables it,the status says that the software/Hardware is disabled and down and when I change it to Root and enables, the status is enable...

jakidaslomoro · 06-18-2020

I am trying to set the freq in the dot11radio1(5.0GHz) but when when I use channel in the int dot11radio 1, it says that it is invalid. Is there anything that I should do? I thought that it is probably due to DFS but that seems not to be the case. ...

jakidaslomoro · 06-13-2016

I have had a Cisco Aironet Wireless bridge 1410 with parabolic antenna that was in operation for 8 years. Last week the root bridge failed in the point to point connection. I replaced it with a new one placed in the same position as a root Bridge als...

jakidaslomoro · 07-31-2020

The software ver is: 15.3(3)JCThanks,

jakidaslomoro · 06-19-2020

Yes, it is for Outdoor bridging between two AP. Sorry, How do check the Country? Thanks,

jakidaslomoro · 06-19-2020

ThiJuba-ACB01-RES#sh controllers dot11radio 1!interface Dot11Radio1Radio Freedom 5, Base Address a453.0e49.39d0, BBlock version 0.00, Software vers ion 4.18.2Serial number: FOC23245ZT2Unused dynamic SQRAM memory: 0x0001F3A8 (124 KB)Unused dynamic SD...

jakidaslomoro · 06-18-2020

The AP power us enough This is actually the issue:Juba-ACB01-RES#conf tJuba-ACB01-RES(config)#int dot11radio 1Juba-ACB01-RES(config-if)#channel 5825^% Invalid input detected at '^' marker.Juba-ACB01-RES(config-if)# I cannot use channel to set the f...

jakidaslomoro · 06-14-2016

John, The software ver is not the same with the previous Bridge. As for th the config file, I modified an old config to port to the new one with the same parameters i.e IP address , Role, ssid and the channel. May do I need to delete the old config ...

Member Since	‎06-13-2016 09:40 AM
Date Last Visited	‎10-12-2020 01:13 AM
Posts	10

User Statistics

User Activity

AIR-AP1572EAC fails to reset to default

dot11radio 0 interface stuck at Reset / down on AP1572EAC

Configuring wireless Bridge on AIR-AP1572EAC-E-K9

Cannot set the channel frequency in the Radio of Cisco Aironet 1572EAC in the 5.0GHz

Cisco aironet wireless Bridge 1400

Re: Configuring wireless Bridge on AIR-AP1572EAC-E-K9

Re: Cannot set the channel frequency in the Radio of Cisco Aironet 1572EAC in the 5.0GHz

Re: Cannot set the channel frequency in the Radio of Cisco Aironet 1572EAC in the 5.0GHz

Re: Cannot set the channel frequency in the Radio of Cisco Aironet 1572EAC in the 5.0GHz

John,