About chris-lawrence

chris-lawrence · 03-18-2023

Team,I am having a heck of a time trying to load and run the NX-OS 9000v. I know about the serial configuration. I'm trying to eventually get to the "leaving grub land" but I never get anywhere near it. And yes I know about the loader > and can run a...

chris-lawrence · 02-18-2023

Team,I'm trying to edit my private CA I use for EAP Authentication with my PSN's. For the EAP-TLS, everything works great - policy set validates the SHA-256(etc) for certificate handshakes and my endpoints are authenticated to the network. What I am ...

chris-lawrence · 08-27-2021

Team, I am using:Version 3.0.0.458Installed Patches 2Product Identifier (PID) ISE-VM-K9Version Identifier (VID) V01ADE-OS Version 3.0.8.091 In my LAB, I have a single ISE that is doing everything (PAN, PSN, MnT) and is the root and hopefully the EP C...

chris-lawrence · 08-19-2021

Team, I am using: Version 3.0.0.458Installed Patches 2Product Identifier (PID) ISE-VM-K9Version Identifier (VID) V01ADE-OS Version 3.0.8.091 I have a question about “stacking” profiles. By stacking, I mean, I have setup ISE to NMAP and profile an fac...

chris-lawrence · 05-17-2021

Hi Team,I am developing a profile service on ISE 3.0patch2. I am trying to develop a multi-pass approach where I can profile the endpoint properly based on OUI + class identifier to get me to a point where my system is confident enough that its one o...

chris-lawrence · 03-22-2023

To be helpful the the community - I found that this was related to using alternate interfaces (other than GE0) as the UI interface. I had the same problem exceeding patch 3 - I reconfigured my cluster to place the UI on the GE0 with the other deploym...

chris-lawrence · 03-22-2023

Hi Lebowski1991Yes I did have a look at this... when I received the Boot Time 3/18/2023 <timestamp> I thought that the switch was stuck. It wasn't until I noticed somewhere that this was normal for the version I am using. I wouldn't see the "leaving ...

chris-lawrence · 02-23-2023

poongarg,Thanks for your reply - I don't have an issue with the p7b - I got the issuing ca and root into the trusted certificates section of my ISE 3.1 build - My issue is I cannot "edit" these trusted certificates so that I can define a CRL URL as I...

chris-lawrence · 11-15-2022

Hi David,My use case was that I was using a common NAD that provides potential access to two different customers. Customer 1 (BLACK) would come in on a VRF'ed zone and the AuthC would be directed to the BLACK-ACS (at this time, we were not using ISE)...

chris-lawrence · 11-02-2022

Perhaps I can think about this tomorrow and report back to you if I think about something…

Member Since	‎04-28-2004 06:25 AM
Date Last Visited	‎03-22-2023 10:40 AM
Posts	60
Total Helpful Votes Received	15

User Statistics

User Activity

Nexus 9000v Boot

Edit Trusted Certificate ISE 3.1.0.518 P3 of my Private CA

Endpoint On-boarding using Internal ISE CA

Transitioning Through Profiles (Profile Stacking)

Cisco ISE3.0Patch2 - NMAP Scan Action

Re: Edit Trusted Certificate ISE 3.1.0.518 P3 of my Private CA

Re: Nexus 9000v Boot

Re: Edit Trusted Certificate ISE 3.1.0.518 P3 of my Private CA

Re: Wired DOT1X Authentication using List Name /NOT default

Re: Wired DOT1X Authentication using List Name /NOT default