About Carlos Bergia

Carlos Bergia · 06-14-2015

Hi, I have the following: A router with:-Interface A facing Internet where I have a VPN site to site configured-Interface B facing a customer with private IP address-Interface C facing my LANThe traffic coming from A (the network coming from VPN tunn...

Carlos Bergia · 11-25-2014

Hi all, I have a 2811 [Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(11)XJ, RELEASE SOFTWARE (fc1)] and I don´t know why, sometimes the router just stop routing. I perform a "show ip route" or "show arp" and seems to be ...

Carlos Bergia · 06-24-2014

Hi, I have this situation:A client of mine has a switched network. On that network where no vlan is configured, he has multiple IP address on the same vlan (vlan 1). So, I´ve installed a 5505 with two vlans, and asigned each vlan to ethernet interfac...

Carlos Bergia · 08-19-2011

Hi, anyone knows if there is a way to configure a secondary ip address (over the same address range) in a vlan interface on the SGE2000?For example, I want Interface Vlan 10 on mw switch has 172.16.10.1/24 and 172.16.10.2/24. Is that possible? If I t...

Carlos Bergia · 08-04-2011

Hi, I have a new SFE300 with 24ports. The switch works fine, but after 4 or 5 hours it reboots it self. After reebots it works fine for another 4 or 5 hours.The only message I get is:Emergency %OS-F-MEMORY: OSMEMG_rn_free: Memory magic is invalid *...

Carlos Bergia · 11-26-2014

My LAN subnet is 10.20.0.0/16.NAT inside statement is because over the Fe0/0 I have a site to site vpn, and I need to NAT the traffic coming from that VPN and going through Fe0/1 (client).The users on the LAN access to Internet via a ISA server and n...

Carlos Bergia · 11-26-2014

!!crypto isakmp policy 1 encr aes 256 authentication pre-share group 5!crypto isakmp policy 10 encr 3des authentication pre-share group 2crypto isakmp key **** address **** no-xauth!crypto isakmp client configuration group vpn key voicentersdm pool S...

Carlos Bergia · 11-26-2014

Hi, first thanks for your responses. --I have syslog configured in warning level and no messages were displayed.--There is not an ISP issue because during the problem, I can ping from the router.--There is not firewall. Something that may be very use...

Carlos Bergia · 08-08-2011

Hi Dave, I updated the software and since then the switch is working fine. I think that the problem is solved with your solution.Thank you very much!Carlos

Carlos Bergia · 06-27-2011

Amit, the complete scenario is this: I have 2 static nat rules: static (inside,outside) 190.1.1.1 192.168.1.1 netmask 255.255.255.255static (inside,outside) 190.1.1.2 192.168.1.2 netmask 255.255.255.255what I want to do is change that nat to have thi...

Member Since	‎12-15-2010 07:47 AM
Date Last Visited	‎09-19-2018 06:25 AM
Posts	14

User Statistics

User Activity

Nat inside and outside on the same interface

Router 2811 stop routing

ASA inter-vlan routing

SGE2000 - Multiple IP address on the sameinterface

SFE300 reboots every 4 or 5 hours

My LAN subnet is 10.20.0.0/16

!!crypto isakmp policy 1 encr

Hi, first thanks for your

SFE300 reboots every 4 or 5 hours

ASK THE EXPERTS : Configuring and Troubleshooting NAT and Failov