Hello All, I want to create a IP SLA so that I can monitor UP time for ISP's as the I Ethernet connectivity, so if there link down beyond the mux, i cannot find that when it went down and at what time it came back, Basically for how long it? So i want to set IP SLA between CE-PE and same i want to plot a graph in MTRG so that NOC team can motinor as well we can pull historical report for that link.   Can you please suggest if this is achievable? if yes than how can i achieve this?   Thanks Jagdev ... View more

Hello All, I have Active/Active, multi homed BGP, dual router , HSRP config on LAN,  Now I want to  change the HSRP priority to avoid one extra hop in case one ISP fails, I want to use the EEM feature instead of IP SLA  which I am currently using But It’s the first time I am trying to use this, Can you guys help me to find whether my EEM config is good enough to achieve what I am trying to achieve or I need to make some changes to this config ISP1 event manager applet track-bgp-down event syslog pattern "%BGP-5-ADJCHANGE: neighbor 10.10.10.17 Down BGP Notification sent" action 1.0 syslog priority critical msg "EBGP Session to peer is down" action 2.0 cli command "enable" action 3.0 cli command "conifg t" action 4.0 cli command "FastEthernet0/1.90" action 5.0 cli command " standby 12 priority 85 " action 6.0 cli command "end" event manager applet track-bgp-up event syslog pattern "%BGP-5-ADJCHANGE: neighbor 10.10.10.17 Up" action 1.0 syslog priority critical msg "EBGP Session to peer is up" action 2.0 cli command "enable" action 3.0 cli command "conifg t" action 4.0 cli command "FastEthernet0/1.90" action 5.0 cli command " standby 12 priority 110 " action 6.0 cli command "end" ISP2 event manager applet track-bgp-down event syslog pattern "%BGP-5-ADJCHANGE: neighbor 20.20.20.41 Down BGP Notification sent" action 1.0 syslog priority critical msg "EBGP Session to peer is down" action 2.0 cli command "enable" action 3.0 cli command "conifg t" action 4.0 cli command "FastEthernet0/1.90" action 5.0 cli command " standby 11 priority 85 " action 6.0 cli command "end" event manager applet track-bgp-up event syslog pattern "%BGP-5-ADJCHANGE: neighbor 20.20.20.41 Up" action 1.0 syslog priority critical msg "EBGP Session to peer is up" action 2.0 cli command "enable" action 3.0 cli command "conifg t" action 4.0 cli command "interface FastEthernet0/1.90" action 5.0 cli command " standby 11 priority 110 " action 6.0 cli command "end" Thanks Jagdev ... View more

Hi All, Please help me to calculate the BGP table size in terms of memory required, I got the information from looking glass. Guide my which components i need to add and than calculate the memory size required. BGP table version is 262538329, main routing table version 262538329 454321 network entries using 53155557 bytes of memory 908642 path entries using 47249384 bytes of memory 98794/69504 BGP path/bestpath attribute entries using 12250456 bytes of memory 51 BGP rrinfo entries using 1224 bytes of memory 86096 BGP AS-PATH entries using 2220164 bytes of memory 70 BGP community entries using 1924 bytes of memory 20 BGP extended community entries using 496 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 114879205 total bytes of memory BGP activity 14224881/13758829 prefixes, 70150237/69218155 paths, scan interval 60 secs If i would be multihomeing with two ISPs with full BGP table and than how should  I calculate the memory requirement for router? Thanks In advance. Jagdev ... View more