Beware of trying to port-channel interfaces across different line cards. The QoS scheduling can be different and not allow a port-channel to come up. See the difference below: sh int te7/12 cap TenGigabitEthernet7/12   Model:                 WS-X6716-10GE   Type:                  10Gbase-SR   Speed:                 10000   Duplex:                full   Trunk encap. type:     802.1Q   Trunk mode:            on,off,desirable,nonegotiate   Channel:               yes   Broadcast suppression: percentage(0-100)   Flowcontrol:           rx-(off,on),tx-(off,on)   Membership:            static   Fast Start:            yes   QOS scheduling:        rx-(1p7q2t), tx-(1p7q4t)   QOS queueing mode:     rx-(cos,dscp), tx-(cos,dscp)   CoS rewrite:           yes   ToS rewrite:           yes   Inline power:          no   Inline power policing: no   SPAN:                  source/destination   UDLD                   yes   Link Debounce:         yes   Link Debounce Time:    yes   Ports-in-ASIC (Sub-port ASIC) : 9-16 (9-12)   Remote switch uplink:  no   Dot1x:                 yes   Port-Security:         yes sh int te6/1 cap TenGigabitEthernet6/1   Model:                 WS-X6708-10GE   Type:                  10Gbase-SR   Speed:                 10000   Duplex:                full   Trunk encap. type:     802.1Q,ISL   Trunk mode:            on,off,desirable,nonegotiate   Channel:               yes   Broadcast suppression: percentage(0-100)   Flowcontrol:           rx-(off,on),tx-(off,on)   Membership:            static   Fast Start:            yes QOS scheduling:        rx-(8q4t), tx-(1p7q4t)   QOS queueing mode:     rx-(cos,dscp), tx-(cos,dscp)   CoS rewrite:           yes   ToS rewrite:           yes   Inline power:          no   Inline power policing: no   SPAN:                  source/destination   UDLD                   yes   Link Debounce:         yes   Link Debounce Time:    yes   Ports-in-ASIC (Sub-port ASIC) : 1,4-5,7 (1)   Remote switch uplink:  no   Dot1x:                 yes   Port-Security:         yes This is the error you will see: %EC-SP-5-CANNOT_BUNDLE2: Te7/12 is not compatible with Te6/1 and will be suspended (qos-card types of Te7/12 do not match Te6/1) Enter the command below on the port-channel to allow the grouping of the ports #no mls qos channel-consistency That being said I hope I can bundle interfaces of different optic types i.e. 10Gbase-SR and 10Gbase-LRM ... View more

Just resolved this issue. My cms database was corrupt. Luckily I had a backup, and was able to perform a restore as detailed in the WAAS configuration guide. My CM webpage is now accessible! ... View more

Hi, Did you find a resolution for this problem? I too am experiencing the same issue after the Central Manager lost power and restarted. ... View more

Hi Daniel, The GMT time is displayed on the dashboard page in the top right corner. I do not see where I can configure my time zone to be +8. Any assistance is appreciated. Thanks, John ... View more

Hi Reza, Thanks for your reply! I understand that the Nexus allocates different power budgets for FAB's, Modules, Fans etc.... but my question is whether the allocation is configurable. In our scenario we will only ever be using 8 of the 32 ports in the N7K-M132XP-12 line card. The Nexus has allocated 750W for the card but with only 8 ports in use it will never need 750W. Thus I'd like to allocate the power that will not be used elsewhere i.e. to support a new line card that we will install without needing to upgrade or install more PSU's (we currently do not have enough power for the additional card) Cheers ... View more

Yes "cms enable" is configured. ... View more