About rizwanr74

rizwanr74 · 12-31-2025

Hello Ladies/Gents,I have been trying out MPLS setup on GNS3 Lab. I cannot ping from CE Device: i.e. CE-R11 to CE-R12, these two routers are connected to opposite end of the lab devices.3 routers namely R3, R6 and R1 are core routers running OSPF an...

rizwanr74 · 12-05-2025

Hello Ladies/Gents,I am trying to establish a proof of concept to push local vlan101 to cross WAN Link to remote NXOS 9k switch running EVPN Vxlan.Please see the config below from two switches, all helpful posts will be rated.The config does not seem...

rizwanr74 · 11-03-2021

Hi guy I have got APs one is: AIR-AP4800-A-K9 and other is AIR-AP3802-i-K9, neither of them broadcasting SSID.I am able to login to web-console and wlan is enabled.I powered them via Cisco DC injector and through none-cisco PoE switch (i.e. netgear ...

rizwanr74 · 12-11-2017

Hi Guys,. I have strange problem with VPN filter that I have on my L2L IPSect tunnel on ASA. access-list MY_VPN_Filter extended permit tcp host 20.183.75.152 eq 1414 host 16.19.56.60 access-list MY_VPN_Filter extended permit tcp host 20.183.75.15...

rizwanr74 · 08-07-2016

Hello Gents, I have two SSIDs one for corporate users (Corp-SSID) with certificate base EAP-TLS authentication and its policy is configured on Win2008 MS Radius server as first policy and I have another SSID (corp-mobile) for Cisco 7926G wifi phones,...

rizwanr74 · 01-01-2026

Hi Harold,Thank you very much for your input, yes indeed you were on the right track, that resolved my issue.The changing mask from /24 to /32 on Loopback0 and Loopback1 on PE-R4 and R3 have solved the issue, however on PE-R8 doesn't seem to bother w...

rizwanr74 · 12-06-2025

Hi Pavel,I configured loopback0 on the 'interface nve1' on both switches, it resolved the issue, it make sense, bgp is sourced from loopback0, therefore 'interface nve1' must be sourced from loopback0 as well.interface nve1source-interface loopback0T...

rizwanr74 · 12-06-2025

HI Pavel,Thanks for your input.My initial configuration did contained with unique ip-address for Lo1 on both switches on /32 mask.c1) _"Configure Lo1 with unique IP and configure one more Loopback (254 for example) with shared address of RP. "_I don'...

rizwanr74 · 12-06-2025

This is new configuration and yet it did not help, please have a look. NXOS9K-SW1# ter le 0NXOS9K-SW1# show run!Command: show running-config!Running configuration last done at: Sat Dec 6 12:35:39 2025!Time: Sat Dec 6 12:37:13 2025version 10.6(1) B...

rizwanr74 · 12-06-2025

Hi Pavel,Thank you for input.Are you telling that RP ip address: 10.200.150.1 and 10.100.150.1 must be a common between two switches?this address in question, must be advertised in IGRP between sites or it is only local to local-site alone?Gee, I thr...

Member Since	‎02-12-2008 12:19 PM
Date Last Visited	‎01-01-2026 07:34 PM
Posts	1,357
Total Helpful Votes Received	368

User Statistics

User Activity

MPLS lab, Two CE routers on 2 opposite end cannot ping each other

EVPN VLXAN issue, does not pass local traffic to remote NxOS

AIR-AP4800-A-K9 is not broadcasting SSID

L2L VPN tunnel filter does not work as expected.

Two SSID on Cisco WLC with two Radius policy MS Radius Srv

Re: MPLS lab, Two CE routers on 2 opposite end cannot ping each other

Re: EVPN VLXAN issue, does not pass local traffic to remote NxOS

Re: EVPN VLXAN issue, does not pass local traffic to remote NxOS

Re: EVPN VLXAN issue, does not pass local traffic to remote NxOS

Re: EVPN VLXAN issue, does not pass local traffic to remote NxOS