About DON BROWN

DON BROWN · 03-13-2021

We currently have C1111 router with IPSEC tunnels to other branches.ASA is being implemented behind router to provide Anyconnect VPN connections.We are wanting to have all VPN connections established to the Head Office ASA and provide access to the b...

DON BROWN · 10-21-2020

Here is what I am trying to do.Outside-1 1.1.1.1/28Outside-2 2.2.2.2/30Additional IP's routed to Outside-2 2.2.20.0/29Inside 172.16.22.0/24Host-A 172.16.22.50nat (inside,Outside-1) dynamic Host-A 1.1.1.5nat (inside,Outside-2) dynamic HOST-A 2.2.20.5D...

DON BROWN · 10-12-2020

DON BROWN ‎10-11-2020 10:55 PMEdited On: ‎10-11-2020 ‎10:55 PMThe 887VA router is generating many of the following error.We have tried 2 different 887VA routers and multiple IOS versions and all are getting this type of error.We currently hav...

DON BROWN · 10-07-2020

We have 2 ISP connecting to 2 Interfaces.AnyConnect currently configured on Outside1Can I configure AnyConnect on Outside2 to allow client VPN connection on either Outside interface ?If possible I presume I will need new;Connection profileGroup Polic...

DON BROWN · 09-21-2020

I have IOS version 157-3.M7 on C881 RouterTrying to connect PPPoE to ISPRelevant Config ... vpdn enable!vpdn-group 1!interface FastEthernet4description NBN Connection to Internetno ip addressip nbar protocol-discoveryip nat outsideip virtual-reassemb...

DON BROWN · 03-13-2021

ThanksASA is FP1120 with licensing for IPSEC and AnyConnectRouter is C1111-K9.Looking for example where AnyConnect VPN connects and then accesses remotesite over IPSEC tunnelThanks Don

DON BROWN · 03-13-2021

We currently have C1111 router with IPSEC tunnels to other branches.ASA is being implemented behind router to provide Anyconnect VPN connections.We are wanting to have all VPN connections established to the Head Office ASA and provide access to the b...

DON BROWN · 10-25-2020

Without the second route asp drop showed packets dropped due to no route.Also testing with telnet would fail as previously advised from the captures.After adding the route telnet was successful, packet capture on the Outside-2 interface shows the ret...

DON BROWN · 10-25-2020

I now have the following routes; route Outside-1 0.0.0.0 0.0.0.0 1.1.1.2 1route Outside-2 0.0.0.0 0.0.0.0 2.2.2.1 2 After adding the second route traffic initiating from Outside-2 was processed successfully and the response received.

DON BROWN · 10-25-2020

We added a second default route to Outside-2 which resolved the problem.An established connection on ASA does NOT work the same as on IPTables on Linux.The sh asp drop indicated no route to host. This has solved the problem

Member Since	‎06-11-2013 01:14 AM
Date Last Visited	‎05-30-2024 01:01 AM
Posts	35
Total Helpful Votes Received	5

User Statistics

User Activity

Anyconnect to Head Office and IPSEC Tunnels to branches - How to route VPN Connection

ASA 2xOutside NAT using both Outside to same Inside Host

Cisco 887VA Error Messages

Can ASA support AnyConnect connection on two Outside interfaces at the same time

PPPoE on C881-K9 failing

Re: Anyconnect to Head Office and IPSEC Tunnels to branches - How to route VPN Connection

Anyconnect to Head Office and IPSEC Tunnels to branches - How to route VPN Connection

Re: ASA 2xOutside NAT using both Outside to same Inside Host

Re: ASA 2xOutside NAT using both Outside to same Inside Host

Re: ASA 2xOutside NAT using both Outside to same Inside Host