Thank you all very much!!! ... View more

OK. I figured it out. Sorry for the hustle and your help everyone. On the laptop and PC I have also WiFi cards installed. When they are turn on i can't ping from hosts when I turn WiFi connections off, hosts are able to ping each other. I did not know that can impact connectivity - I discovered it by accident. Sorry guys - I know I was pain i the a.s. Can anyone can tell me why it works this way? Thank you all very much!!! -------------------------------------- ... View more

R1 Router---1#show controllers serial 0 Interface Serial0 Hardware is PowerQUICC MPC860 DTE V.35 TX and RX clocks detected. idb at 0x832E391C, driver data structure at 0x832EB028 SCC Registers: General [GSMR]=0x2:0x00000030, Protocol-specific [PSMR]=0x8 Events [SCCE]=0x0000, Mask [SCCM]=0x001F, Status [SCCS]=0x06 Transmit on Demand [TODR]=0x0, Data Sync [DSR]=0x7E7E Interrupt Registers: Config [CICR]=0x00365F80, Pending [CIPR]=0x00008000 Mask   [CIMR]=0x40204000, In-srv  [CISR]=0x00000000 Command register [CR]=0x600 Port A [PADIR]=0x0000, [PAPAR]=0x0903        [PAODR]=0x0000, [PADAT]=0xFFFD Port B [PBDIR]=0x0180F, [PBPAR]=0x0E00E        [PBODR]=0x00000, [PBDAT]=0x0057C Port C [PCDIR]=0x000, [PCPAR]=0x000        [PCSO]=0x020,  [PCDAT]=0xFCC, [PCINT]=0x000 Receive Ring         rmd(FF003030): status 9000 length 12 address 720FDE4         rmd(FF003038): status 9000 length 12 address 7210464         rmd(FF003040): status 9000 length 12 address 7210AE4         rmd(FF003048): status 9000 length 12 address 7211164         rmd(FF003050): status 9000 length 12 address 72117E4         rmd(FF003058): status 9000 length 12 address 7211E64         rmd(FF003060): status 9000 length 34 address 7212B64         rmd(FF003068): status 9000 length 2E address 72131E4         rmd(FF003070): status 9000 length 2E address 7213864         rmd(FF003078): status 9000 length 12 address 7213EE4         rmd(FF003080): status 9000 length 12 address 720D6E4         rmd(FF003088): status 9000 length 12 address 720F764         rmd(FF003090): status 9000 length 12 address 720DD64         rmd(FF003098): status 9000 length 12 address 720E3E4         rmd(FF0030A0): status 9000 length 12 address 720EA64         rmd(FF0030A8): status B000 length 153 address 720F0E4 Transmit Ring         tmd(FF0030B0): status 5C00 length 2C address 721C3F4         tmd(FF0030B8): status 5C00 length 10 address 720D6E4         tmd(FF0030C0): status 5C00 length 10 address 70CFA14         tmd(FF0030C8): status 5C00 length 10 address 720DD64         tmd(FF0030D0): status 5C00 length 10 address 70CFC94         tmd(FF0030D8): status 5C00 length 10 address 720EA64         tmd(FF0030E0): status 5C00 length 10 address 70D0054         tmd(FF0030E8): status 5C00 length 10 address 7210464         tmd(FF0030F0): status 5C00 length 10 address 70D02D4         tmd(FF0030F8): status 5C00 length 151 address 72307B4         tmd(FF003100): status 5C00 length 10 address 7211164         tmd(FF003108): status 5C00 length 10 address 70D0694         tmd(FF003110): status 5C00 length 10 address 7211E64         tmd(FF003118): status 5C00 length 10 address 70D07D4         tmd(FF003120): status 5C00 length 10 address 7212B64         tmd(FF003128): status 7C00 length 10 address 70D0914 tx_limited=0(16) SCC GENERAL PARAMETER RAM (at 0xFF003C00) Rx BD Base [RBASE]=0x3030, Fn Code [RFCR]=0x18 Tx BD Base [TBASE]=0x30B0, Fn Code [TFCR]=0x18 Max Rx Buff Len [MRBLR]=1548 Rx State [RSTATE]=0x18008440, BD Ptr [RBPTR]=0x3070 Tx State [TSTATE]=0x18000548, BD Ptr [TBPTR]=0x30B0 SCC HDLC PARAMETER RAM (at 0xFF003C38) CRC Preset [C_PRES]=0xFFFF, Mask [C_MASK]=0xF0B8 Errors: CRC [CRCEC]=0, Aborts [ABTSC]=0, Discards [DISFC]=0 Nonmatch Addr Cntr [NMARC]=0 Retry Count [RETRC]=0 Max Frame Length [MFLR]=1610 Rx Int Threshold [RFTHR]=0, Frame Cnt [RFCNT]=65352 User-defined Address 0000/0000/0000/0000 User-defined Address Mask 0x0000 buffer size 1524 PowerQUICC SCC specific errors: 0 input aborts on receiving flag sequence 0 throttles, 0 enables 0 overruns 0 transmitter underruns 0 transmitter CTS losts Router---1#sh int serial 0 Serial0 is up, line protocol is up   Hardware is PowerQUICC Serial   Internet address is 192.168.1.66/26   MTU 1500 bytes, BW 1544 Kbit/sec, DLY 20000 usec,      reliability 255/255, txload 1/255, rxload 1/255   Encapsulation PPP, LCP Open   Open: IPCP, CDPCP, loopback not set   Keepalive set (10 sec)   Last input 00:00:00, output 00:00:00, output hang never   Last clearing of "show interface" counters 00:10:28   Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0   Queueing strategy: fifo   Output queue: 0/40 (size/max)   5 minute input rate 0 bits/sec, 0 packets/sec   5 minute output rate 0 bits/sec, 0 packets/sec      207 packets input, 9583 bytes, 0 no buffer      Received 0 broadcasts, 0 runts, 0 giants, 0 throttles      1 input errors, 0 CRC, 1 frame, 0 overrun, 0 ignored, 0 abort      232 packets output, 10702 bytes, 0 underruns      0 output errors, 0 collisions, 1 interface resets      1 unknown protocol drops      0 output buffer failures, 0 output buffers swapped out      0 carrier transitions      DCD=up  DSR=up  DTR=up  RTS=up  CTS=up ================================================================================ R2 Router---2#show controllers serial 0 Interface Serial0 Hardware is PowerQUICC MPC860 DCE V.35, clock rate 56000 idb at 0x832475C0, driver data structure at 0x8324ECCC SCC Registers: General [GSMR]=0x2:0x00000030, Protocol-specific [PSMR]=0x8 Events [SCCE]=0x0000, Mask [SCCM]=0x001F, Status [SCCS]=0x06 Transmit on Demand [TODR]=0x0, Data Sync [DSR]=0x7E7E Interrupt Registers: Config [CICR]=0x00365F80, Pending [CIPR]=0x00000804 Mask   [CIMR]=0x68200400, In-srv  [CISR]=0x00000000 Command register [CR]=0x640 Port A [PADIR]=0x1500, [PAPAR]=0x9FCF        [PAODR]=0x0000, [PADAT]=0x79F7 Port B [PBDIR]=0x0BC0F, [PBPAR]=0x0D00E        [PBODR]=0x00000, [PBDAT]=0x091DC Port C [PCDIR]=0x008, [PCPAR]=0x000        [PCSO]=0x8A0,  [PCDAT]=0xB34, [PCINT]=0x000 Receive Ring         rmd(FF003130): status 9000 length 2E address 7230FE4         rmd(FF003138): status 9000 length 12 address 7231664         rmd(FF003140): status 9000 length 12 address 722AE64         rmd(FF003148): status 9000 length 30 address 722B4E4         rmd(FF003150): status 9000 length 2E address 722BB64         rmd(FF003158): status 9000 length 2E address 722C1E4         rmd(FF003160): status 9000 length 2E address 722C864         rmd(FF003168): status 9000 length 30 address 722CEE4         rmd(FF003170): status 9000 length 2E address 722D564         rmd(FF003178): status 9000 length 30 address 722DBE4         rmd(FF003180): status 9000 length 30 address 722E264         rmd(FF003188): status 9000 length 2E address 722E8E4         rmd(FF003190): status 9000 length 30 address 722EF64         rmd(FF003198): status 9000 length 30 address 722F5E4         rmd(FF0031A0): status 9000 length 30 address 722FC64         rmd(FF0031A8): status B000 length 30 address 72302E4 Transmit Ring         tmd(FF0031B0): status 5C00 length 25C address 723A134         tmd(FF0031B8): status 5C00 length 1CF address 723A474         tmd(FF0031C0): status 5C00 length 1CF address 7239DF4         tmd(FF0031C8): status 5C00 length 87 address 723A7B4         tmd(FF0031D0): status 5C00 length 87 address 70BB814         tmd(FF0031D8): status 5C00 length 87 address 70BCED4         tmd(FF0031E0): status 5C00 length 87 address 70BBB54         tmd(FF0031E8): status 5C00 length 87 address 723AE34         tmd(FF0031F0): status 5C00 length 87 address 70BC1D4         tmd(FF0031F8): status 5C00 length 87 address 723AAF4         tmd(FF003200): status 5C00 length 87 address 723B174         tmd(FF003208): status 5C00 length 87 address 70BBE94         tmd(FF003210): status 5C00 length 87 address 70BE594         tmd(FF003218): status 5C00 length 87 address 70BE254         tmd(FF003220): status 5C00 length 87 address 723B4B4         tmd(FF003228): status 7C00 length 60 address 723BB34 tx_limited=1(2) SCC GENERAL PARAMETER RAM (at 0xFF003D00) Rx BD Base [RBASE]=0x3130, Fn Code [RFCR]=0x18 Tx BD Base [TBASE]=0x31B0, Fn Code [TFCR]=0x18 Max Rx Buff Len [MRBLR]=1548 Rx State [RSTATE]=0x18008440, BD Ptr [RBPTR]=0x31A8 Tx State [TSTATE]=0x18000548, BD Ptr [TBPTR]=0x31F0 SCC HDLC PARAMETER RAM (at 0xFF003D38) CRC Preset [C_PRES]=0xFFFF, Mask [C_MASK]=0xF0B8 Errors: CRC [CRCEC]=0, Aborts [ABTSC]=0, Discards [DISFC]=0 Nonmatch Addr Cntr [NMARC]=0 Retry Count [RETRC]=0 Max Frame Length [MFLR]=1610 Rx Int Threshold [RFTHR]=0, Frame Cnt [RFCNT]=65176 User-defined Address 0000/0000/0000/0000 User-defined Address Mask 0x0000 buffer size 1524 PowerQUICC SCC specific errors: 0 input aborts on receiving flag sequence 0 throttles, 0 enables 0 overruns 0 transmitter underruns 0 transmitter CTS losts Router---2#show interfaces serial 0 Serial0 is up, line protocol is up   Hardware is PowerQUICC Serial   Internet address is 192.168.1.65/26   MTU 1500 bytes, BW 1544 Kbit/sec, DLY 20000 usec,      reliability 255/255, txload 1/255, rxload 1/255   Encapsulation PPP, LCP Open   Open: IPCP, CDPCP, loopback not set   Keepalive set (10 sec)   Last input 00:00:00, output 00:00:00, output hang never   Last clearing of "show interface" counters 00:13:36   Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0   Queueing strategy: weighted fair   Output queue: 0/1000/64/0 (size/max total/threshold/drops)      Conversations  0/2/256 (active/max active/max total)      Reserved Conversations 0/0 (allocated/max allocated)      Available Bandwidth 1158 kilobits/sec   5 minute input rate 0 bits/sec, 2 packets/sec   5 minute output rate 5000 bits/sec, 13 packets/sec      861 packets input, 42168 bytes, 0 no buffer      Received 0 broadcasts, 0 runts, 0 giants, 0 throttles      0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort      4048 packets output, 194804 bytes, 0 underruns      0 output errors, 0 collisions, 1 interface resets      1 unknown protocol drops      0 output buffer failures, 0 output buffers swapped out      7 carrier transitions      DCD=up  DSR=up  DTR=up  RTS=up  CTS=up Here you go - I personally don't know what all taht means. And by the way - when I turned on my lab today I couldn't ping host .1 anymore. ... View more

Hi Yeah I know thats something really odd is going on. I will post it tomorrow cause now i need to go to bed - I'm working in the morning. Thanks all for your responses. I'll be back tomorrow. Once again thanks. Good night. ... View more

Hi Thats is exactly how i got this set up. There is a PPT file attached to my post #1 on the top of this page - so you can see it clearly. Thanks ... View more

Hi WOW. I took an hour brake. Came back and typed the command Router---1#debug ip routing IP routing debugging is on Router---2#debug ip routing IP routing debugging is on Now when I'm pinging from the .133 laptop i can reach .1 PC !!! The output I'm getting from the Router 1: Router---1#debug ip routing IP routing debugging is on Router---1# *Mar  1 10:34:21.279: RT: NET-RED 0.0.0.0/0 These messages are showing every 1 minute. *Mar  1 10:36:21.279: RT: NET-RED 0.0.0.0/0 Router---1# *Mar  1 10:37:21.279: RT: NET-RED 0.0.0.0/0 Router---1# *Mar  1 10:38:21.279: RT: NET-RED 0.0.0.0/0 There is nothing showing on Router 2 and still cant ping .133 host from .1 What have i done that now i'm able to ping from .133 - typing debug command was all i did??? ... View more

OK I've run that on the Router 2: Router---2#debug ip packet detail IP packet debugging is on (detailed) Now I'm generating traffic (pinging laptop .133 on the other side) but i can't see any outcome on the router. How do I do that? Thanks. ... View more

Thanks a lot. Have you got any idea what may causing this? I have all firewalls disabled. Maybe it's the switch that is doing something odd - i'm just guessing here. ... View more

OK Router 1 -------------------------------------------------------------------- Router---1#ping 192.168.1.1 source 192.168.1.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds: Packet sent with a source address of 192.168.1.129 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/33/36 ms Router---1#ping 192.168.1.2 source 192.168.1.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds: Packet sent with a source address of 192.168.1.129 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/33/36 ms Router 2 ------------------------------------------------------------------------- Router---2#ping 192.168.1.129 source 192.168.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.129, timeout is 2 seconds: Packet sent with a source address of 192.168.1.2 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 40/45/68 ms Router---2#ping 192.168.1.133 source 192.168.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.133, timeout is 2 seconds: Packet sent with a source address of 192.168.1.2 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 40/45/68 ms ... View more

Thats what I'm getting R1 Router---1(config)#ip route 0.0.0.0 0.0.0.0 192.168.1.66 %Invalid next hop address (it's this router) R2 Router---2(config)#ip route 0.0.0.0 0.0.0.0 192.168.1.65 %Invalid next hop address (it's this router) I think you meant R1 .65  and  R2 .66 - i did that. Routing tables: R1 Gateway of last resort is 192.168.1.65 to network 0.0.0.0      192.168.1.0/24 is variably subnetted, 3 subnets, 2 masks C       192.168.1.65/32 is directly connected, Serial0 C       192.168.1.64/26 is directly connected, Serial0 C       192.168.1.128/26 is directly connected, FastEthernet0 S*   0.0.0.0/0 [1/0] via 192.168.1.65 R2 Gateway of last resort is 192.168.1.66 to network 0.0.0.0      192.168.1.0/24 is variably subnetted, 3 subnets, 2 masks C       192.168.1.64/26 is directly connected, Serial0 C       192.168.1.66/32 is directly connected, Serial0 C       192.168.1.0/26 is directly connected, FastEthernet0 S*   0.0.0.0/0 [1/0] via 192.168.1.66 When I'm on routers i can ping every single address on any network: Router1 -------------------------------------------------------------------------------------------------- Router---1#ping 192.168.1.131 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.131, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Router---1#ping 192.168.1.133 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.133, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Router---1#ping 192.168.1.130 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.130, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Router---1#ping 192.168.1.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Router---1#ping 192.168.1.66 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.66, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 64/65/68 ms Router---1#ping 192.168.1.65 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.65, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/33/36 ms Router---1#ping 192.168.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/32/36 ms Router---1#ping 192.168.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/33/36 ms Router2 ------------------------------------------------------------------------------------- Router---2#ping 192.168.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/3/4 ms Router---2#ping 192.168.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/3/4 ms Router---2#ping 192.168.1.65 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.65, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 72/80/108 ms Router---2#ping 192.168.1.66 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.66, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 40/45/68 ms Router---2#ping 192.168.1.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 40/44/64 ms Router---2#ping 192.168.1.130 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.130, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 40/45/68 ms Router---2#ping 192.168.1.131 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.131, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 40/45/68 ms Router---2#ping 192.168.1.133 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.133, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 40/44/64 ms -------------------------------------------------------------------------------------------- So that works! But when pinging from the PC or a laptop: Replay from 192.168.1.64: Destination Host unreachable Replay from 192.168.1.64: Destination Host unreachable Replay from 192.168.1.64: Destination Host unreachable Replay from 192.168.1.64: Destination Host unreachable ... View more

Hi I know I'm being pain in the a.s but because of that i can't sleep. I was going to take CCENT exam soon but now I'm realy in doubt. I did what you suggested and I've chaned encapsulation to HDLC and I was able to ping interface on the other side - BUT only when I was on the router. When I was trying to ping it from my laptops I couldn't. So I understand that they are routing but not all the traffic??? I'm going mad here. I removed all the static routing and if you guys could guide me through it - I'm probably doing some stupid mistake when setting this up. So there is no routing entries and the routing tables are looking like that: ------------ Router1 Gateway of last resort is not set      192.168.1.0/24 is variably subnetted, 3 subnets, 2 masks C       192.168.1.65/32 is directly connected, Serial0 C       192.168.1.64/26 is directly connected, Serial0 C       192.168.1.128/26 is directly connected, FastEthernet0 ---------- Router 2 Gateway of last resort is not set      192.168.1.0/24 is variably subnetted, 3 subnets, 2 masks C       192.168.1.64/26 is directly connected, Serial0 C       192.168.1.66/32 is directly connected, Serial0 C       192.168.1.0/26 is directly connected, FastEthernet0 Routers are able to reach theirs serial interfaces. PC on the 192.168.1.0 network can ping .2 interface but I can't ping .65 interface - it says : Dest Host unreachable. BUT I'm able to get .66 interface of Router1. From the laptops on the 192.168.128 network I can ping .129 interface of Router1 AND its serial interface .66 BUT not .65 What kind of black magic is this???? I'm starting to think that there is something wrong with my hardware. ... View more

Hi guys So i decided I will rebuild the whole thing from the begining. All the addresses and the layout is the same. I was trying to narrow possible causes - so let me start from here. ----------------------------------------------------------------------------------------------------------- When on the Router 2 I can ping Routers 1 both interfaces [ .66 and .129] but when on Router 1 I can only ping serial interface of Router2 [.65] I'm attaching debug below. I need to sort that out!!! Please help me. Thanks. ---------------------------------------------------------------------------------------------------------------- Success rate is 100 percent (5/5), round-trip min/avg/max = 36/37/40 ms Router---1# *Mar 1 06:30:54.511: IP: tableid=0, s=192.168.1.66 (local), d=192.168.1.65 (Serial0), routed via FIB *Mar 1 06:30:54.511: IP: s=192.168.1.66 (local), d=192.168.1.65 (Serial0), len 100, sending *Mar 1 06:30:54.547: IP: tableid=0, s=192.168.1.65 (Serial0), d=192.168.1.66 (Serial0), routed via RIB *Mar 1 06:30:54.547: IP: s=192.168.1.65 (Serial0), d=192.168.1.66 (Serial0), len 100, rcvd 3 *Mar 1 06:30:54.547: IP: tableid=0, s=192.168.1.66 (local), d=192.168.1.65 (Serial0), routed via FIB *Mar 1 06:30:54.551: IP: s=192.168.1.66 (local), d=192.168.1.65 (Serial0), len 100, sending *Mar 1 06:30:54.583: IP: tableid=0, s=192.168.1.65 (Serial0), d=192.168.1.66 (Serial0), routed via RIB *Mar 1 06:30:54.583: IP: s=192.168.1.65 (Serial0), d=192.168.1.66 (Serial0), len 100, rcvd 3 *Mar 1 06:30:54.587: IP: tableid=0, s=192.168.1.66 (local), d=192.168.1.65 (Serial0), routed via FIB *Mar 1 06:30:54.587: IP: s=192.168.1.66 (local), d=192.168.1.65 (Serial0), len 100, sending *Mar Router---1#1 06:30:54.623: IP: tableid=0, s=192.168.1.65 (Serial0), d=192.168.1.66 (Serial0), routed via RIB *Mar 1 06:30:54.623: IP: s=192.168.1.65 (Serial0), d=192.168.1.66 (Serial0), len 100, rcvd 3 *Mar 1 06:30:54.623: IP: tableid=0, s=192.168.1.66 (local), d=192.168.1.65 (Serial0), routed via FIB *Mar 1 06:30:54.623: IP: s=192.168.1.66 (local), d=192.168.1.65 (Serial0), len 100, sending *Mar 1 06:30:54.659: IP: tableid=0, s=192.168.1.65 (Serial0), d=192.168.1.66 (Serial0), routed via RIB *Mar 1 06:30:54.659: IP: s=192.168.1.65 (Serial0), d=192.168.1.66 (Serial0), len 100, rcvd 3 *Mar 1 06:30:54.663: IP: tableid=0, s=192.168.1.66 (local), d=192.168.1.65 (Serial0), routed via FIB *Mar 1 06:30:54.663: IP: s=192.168.1.66 (local), d=192.168.1.65 (Serial0), len 100, sending *Mar 1 06:30:54.695: IP: tableid=0, s=192.168.1.65 (Serial0), d=192.168.1.66 (Serial0), routed via RIB *Mar 1 06:30:54.695: IP: s=192.168.1.65 (Serial0), d=192.168.1.66 (Serial0), len 100, rcvd 3 Router---1# Router---1#ping 192.168.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds: *Mar 1 06:31:19.271: IP: s=192.168.1.66 (local), d=192.168.1.2, len 100, unroutable. *Mar 1 06:31:21.271: IP: s=192.168.1.66 (local), d=192.168.1.2, len 100, unroutable. *Mar 1 06:31:23.271: IP: s=192.168.1.66 (local), d=192.168.1.2, len 100, unroutable. *Mar 1 06:31:25.271: IP: s=192.168.1.66 (local), d=192.168.1.2, len 100, unroutable. *Mar 1 06:31:27.271: IP: s=192.168.1.66 (local), d=192.168.1.2, len 100, unroutable. Success rate is 0 percent (0/5) ... View more

Thanks a lot guys I don't know where to start from now ;] OK. I changed routing on both R1 and R2 so now they using Serial 0 to forward traffic. And now from laptop .133 i can ping everything on this side plus 192.168.1.66. Whan i try to ping .65 BANG! host unreachable. From PC .1 I'm able to ping .2 interface of R2 but not the .65. I'm a really fresh to CISCO but i'm almost certain that there is a problem with Serial 0 int on R2. I will try to setup these logs now- i never done it before so it may take me a while. update- I just tried to ping .2 and .65 from R1. It works fine. ????????????????????????????????????????? Thanks again. ... View more

Are these commands going to be different if I'm using telnet? and also where do i find the output of this debug? Thanks a lot. ... View more

I'm using telnet. ... View more