AireOS 8.0 For AireOS 8.0 customers, TAC recommends 8.0.140.0 (latest CCO release, AKA 8.0MR4) Customers with 1700/2700/3700 access points should consider running the latest 8.2 release, or an 8.0 escalation special (available from TAC) due to CSCus83638 (AP 5Ghz Radio Beaconing but not accepting Client Assoc.) or maybe using DFS channels that the phones do not support A ... View more

http://clients.mikealbano.com/ try this site A ... View more

this is my guess http://www.cisco.com/c/en/us/support/docs/field-notices/639/fn63942.html ... View more

"The small black arrow at the side of each access point represents Side A of each access point, and each access point arrow must correspond with the direction in which the access points were installed." http://www.cisco.com/c/en/us/td/docs/wireless/ncs/1-0/configuration/guide/NCS10cg/maps.html for HyperLocation the arrows on APs should all be in the same direction and the black arrows on prime should correspond. rotate the black Arrow to match the Direction of installed AP For us you can't see the Black arrow since it is under the big blue Arrow head. I would just say that if the AP was mounted incorrectly it should be fixed or replaced with a external Antenna model. A ... View more

Hi Add controller to PI Add map Add APs and place APs to map and then export in CMX the APs will display numbers which indicates # of clients connected A ... View more

Hi Assuming you have configured CMX and controller already As far as I know Prime is currently used only for maps. so import map, size correctly, add APs to map and then export maps. Import map to cmx and you will see clients in CMX. [cmxadmin@CMX ~]$ cmxctl config maps import you can choose to import a file or directly from PI A ... View more

High Utilization When there are large numbers of active wireless users, or the users are operating high-end applications such as Wi-Fi phones or downloading large files, the utilization of the network may be reaching the maximum capacity of the access point. With this condition, the retry rates will be relatively high (greater than 10 percent), even if signal levels are high and noise levels are low (i.e., high SNR). The result is lower throughput per user due to the additional overhead necessary to retransmit data frames. http://www.wi-fiplanet.com/tutorials/article.php/3566706/Troubleshooting-Poor-WLAN-Performance.htm I think the above example is not relevant to a bridge. and my calculation could be wrong - total retries/packets sent and received X 100 Do you have any overruns on ethernet side? please run this command dot11 interface-number carrier busy Performing a Carrier Busy Test You can perform a carrier busy test to check the radio activity on access point channels. During the carrier busy test, the access point drops all associations with wireless networking devices for around 4 seconds while it conducts the carrier test and then displays the test results. In privileged EXEC mode, enter this command to perform a carrier busy test: dot11 interface-number carrier busy For interface-number, enter dot11radio 0 to run the test on the 2.4-GHz radio, or enter dot11radio 1 to run the test on the 5-GHz radio. Use the show dot11 carrier busy command to re-display the carrier busy test results. ... View more

looks like 30% retries which can bring throughput down. ... View more

try using 0 in the excel username 111122223333 password 0 111122223333 =(B1&" "&A1&" "&C1&" "&A1) ... View more

Use excel and create a formula to merge your mac + config so you can copy and paste the output to all your APs. paste the merged fields to a text file to make sure no funky stuff gets carried along. https://support.office.com/en-us/article/Combine-text-from-two-or-more-cells-into-one-cell-81ba0946-ce78-42ed-b3c3-21340eb164a6 A ... View more

I have have never used ACM, but the behavior reminds me of Bonjour. check what protocols are used Check if peer to peer is blocking is enabled on WLAN ... View more

https://supportforums.cisco.com/document/12453081/lightweight-ap-fail-create-capwaplwapp-connection-due-certificate-expiration cert might be expired A ... View more