Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Tim Nomani
08-01-2018
Tim Nomani
Member since
12-22-2009
Beginner
03-29-2010
02:59 PM
Hello all, Looking to migrate many analog phones from a failed PBX using CUCM to register them.. There are more than an handful of phones in the hundreds.. Is the FXS module WS-X6624 that hold the most analog module are there any other MGCP hardware that can support a greater amount of analog phones per module ? Thanks
... View more
Labels:
Created by
Tim Nomani
in IP Telephony and Phones
in IP Telephony and Phones
03-06-2010
02:18 PM
03-06-2010
02:18 PM
I need to purchase some of the SAST where can i fond that part number(s) better yet a Cisco channel partner that sells them. Thanks TN
... View more
Labels:
Created by
Tim Nomani
in Security Documents
in Security Documents
03-01-2010
12:59 PM
03-01-2010
12:59 PM
I guess the only solutions would be having the phone proxy on the ASA.. Thank you
... View more
Created by
Tim Nomani
in Security Documents
in Security Documents
03-01-2010
12:28 PM
03-01-2010
12:28 PM
Well the remote devices are remote users using their Linksys or whatever routes to get to the Internet, only CUCM is behind a ASA..
... View more
Created by
Tim Nomani
in Security Documents
in Security Documents
03-01-2010
12:18 PM
03-01-2010
12:18 PM
Andrew, The security is not a concern (as its a test environment), however the remote phones are only able to register on the CUCM, but there is no media, since they're located in behind NATing in remote locations...
... View more
Created by
Tim Nomani
in Security Documents
in Security Documents
03-01-2010
11:46 AM
03-01-2010
11:46 AM
Is there any other was of registering remote phone to the CUCM without the expensive ASA phone proxy ? Thanks Tim
... View more
03-01-2010
11:45 AM
Well from further research it turns out that my ASA has to have a phone proxy license in order for the remote phones to register and make phone calls.. This is one solutions, I'm looking if there is any other possible way, a more cost effective to register remote phone to a CUCM.. TN
... View more
02-19-2010
09:53 AM
Actually, I have no audio at all... Calls connect just no audio... Thx TN
... View more
02-19-2010
08:18 AM
Yes agree, and makes sense what you said.. One strange thing though how's possible the calls are routed between phones (extensions) from different locations (LAN's) ?, it would ring but there is no audio, which could be caused by a blocked port. What do you think ?
... View more
02-19-2010
08:03 AM
tcatlinins, Thanks for your input, I totally agree that it could be a filter somewhere which I do not have control over. As far as the private IP's not being routable on the WAN I would say that they reach the CUCM using NAT public IP. Other than having a packet delay on the WAN I don;t see any reason why wouldn;t this work even though CUCM is made mostly for LAN environments. I will contunue my experiment and let you know the results.. Thanks again for you reply. TN
... View more
Created by
Tim Nomani
in IP Telephony and Phones
in IP Telephony and Phones
02-16-2010
08:29 AM
02-16-2010
08:29 AM
I have no audio at all.. My setup is 1 VMawre server configured with a public IP. All the phones register from anywhere in the WAN without any issues, however audio is only available on the phone within my LAN anything originated outside have no audio..The only thing I haven;t check was with my ISP if the ports are blocked, but to my knowledge there not. Thx Tim
... View more
Created by
Tim Nomani
in IP Telephony and Phones
in IP Telephony and Phones
02-16-2010
05:37 AM
02-16-2010
05:37 AM
Hi, were you able to resolve it ? I have similar issue not SIP to SIP, but SCCP to SCCP with similar scenario.. Tim
... View more
02-15-2010
01:59 PM
Hello , I have a test CM 6.1 with a public IP, I am able to register phones from anywhere, however I'm only able to hear or talk only with the phones registered on the same segment. Any one can assist on why this happens and how it can be resolved? Thanks Tim
... View more
Labels:
03-29-2010 02:59 PM
Hello all,Looking to migrate many analog phones from a failed PBX using
CUCM to register them.. Ther...
Created by
Tim Nomani
in IP Telephony and Phones
03-06-2010 02:18 PM
03-06-2010 02:18 PM
I need to purchase some of the SAST where can i fond that part number(s)
better yet a Cisco channel ...
Created by
Tim Nomani
in Security Documents
03-01-2010 12:59 PM
03-01-2010 12:59 PM
I guess the only solutions would be having the phone proxy on the
ASA..Thank you
Created by
Tim Nomani
in Security Documents
03-01-2010 12:28 PM
03-01-2010 12:28 PM
Well the remote devices are remote users using their Linksys or whatever
routes to get to the Intern...
Created by
Tim Nomani
in Security Documents
03-01-2010 12:18 PM
03-01-2010 12:18 PM
Andrew,The security is not a concern (as its a test environment),
however the remote phones are only...
Created by
Tim Nomani
in Security Documents
03-01-2010 11:46 AM
03-01-2010 11:46 AM
Is there any other was of registering remote phone to the CUCM without
the expensive ASA phone proxy...
03-01-2010 11:45 AM
Well from further research it turns out that my ASA has to have a phone
proxy license in order for t...
02-19-2010 08:18 AM
Yes agree, and makes sense what you said.. One strange thing though
how's possible the calls are rou...
02-19-2010 08:03 AM
tcatlinins,Thanks for your input, I totally agree that it could be a
filter somewhere which I do not...
Created by
Tim Nomani
in IP Telephony and Phones
02-16-2010 08:29 AM
02-16-2010 08:29 AM
I have no audio at all..My setup is 1 VMawre server configured with a
public IP. All the phones regi...
Created by
Tim Nomani
in IP Telephony and Phones
02-16-2010 05:37 AM
02-16-2010 05:37 AM
Hi,were you able to resolve it ? I have similar issue not SIP to SIP,
but SCCP to SCCP with similar ...
Public Statistics
| Date Registered | 12-22-2009 01:27 PM |
| Date Last Visited | 08-01-2018 02:27 AM |
| Total Messages Posted | 11 |
