Hi, can you please provide further details like what Cisco AP are you using and other products, further detail what you are trying to achieve. ... View more

Please refer to following link, page 120. http://www.cisco.com/c/dam/en/us/td/docs/routers/csbr/rv320/administration/guide/en/rv32x_ag_en.pdf ... View more

Hi Luis, Check following links might help you. http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/vm_fex/vmware/gui/config_guide/2-1/b_GUI_VMware_VM-FEX_UCSM_Configuration_Guide_2_1/b_GUI_VMware_VM-FEX_UCSM_Configuration_Guide_2_1_chapter_0100.html http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/vm_fex/vmware/gui/config_guide/2-1/b_GUI_VMware_VM-FEX_UCSM_Configuration_Guide_2_1/b_GUI_VMware_VM-FEX_UCSM_Configuration_Guide_2_1_chapter_0101.html ... View more

please ignore above link, check following link http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/os-install-guides/windows/b_C-Series_Windows_Install.pdf ... View more

Hi, also check following link. https://supportforums.cisco.com/discussion/12246031/windows-2012-r2-bare-metal-install-b200-m3-local-disk Regards, Shahzad ... View more

Hello Tony, Following are steps to reset FI. The only thing you’ll need is a console cable for the fabric interconnect(s) that you want to recover the passwords on. When you’ve got a connection to the console port of the FI, here are the basic steps:   Reboot the FI Since you cannot login, you need to remove power to the FI by either removing the PSU’s or the power cords (whichever are easiest for you to reach) Press ctrl+shift+r a few times as the interconnect boots to interrupt the boot process <side note> In a normal boot, the FI is programmed to three specific images: kickstart (kernel) system (system) management (UCSM) This happens automatically. If something goes wrong with the boot process, the FI may stop after, before, or during any of these three stages. Depending on where it stops, you will have varying levels of functionality. By interrupting the boot process, you must individually load the images yourself. If you were to reboot at any stage again, the FI will default back to its programmed boot sequence.     Regards, Shahzad   This should leave you at the extremely useful, yet very unfriendly <loader> prompt. The loader has a very limited command list (below): loader> help ? Print the command list boot Boot an image dir List the directory content help Print the command list or reboot Reboot the system resetcmos Reset CMOS to factory defa serial Serial console settings set Set network configuration show Show loader configuration   First, we need to know what kickstart we can invoke via the “boot” command. To get that, type the following: dir You will see output similar to the following: loader> dir bootflash: lost+found ucs-6100-k9-kickstart.4.0.1a.N2.1.1e.bin ucs-6100-k9-system.4.0.1a.N2.1.1e.bin sysdebug chassis.img nuova-sim-mgmt-nsg.0.1.0.001.bin [output truncated]   The kickstart is in bold above. To boot off of this image, I would type: Boot ucs-6100-k9-kickstart.4.0.1a.N2.1.1e.bin   This will load kickstart and stop at the boot prompt. Form here type: switch(boot)# config terminal Enter configuration commands, one per line. End with CNTL/Z. switch(boot)(config)# admin-password mypassword (where mypassword is the password you want to use) ... View more

Hello, Following is the link to Hardware and Software Interoperability Matrix for UCS http://www.cisco.com/c/dam/en/us/td/docs/unified_computing/ucs/interoperability/matrix/r_hcl_B_2-11.pdf Hope this will help Regards, Shahzad ... View more

Hi, Following document will be helpful http://www.cisco.com/c/dam/en/us/solutions/collateral/data-center-virtualization/unified-computing/whitepaper_C11-718938.pdf Regards, Shahzad ... View more

Hi Please check following link may be useful. http://www.cisco.com/c/en/us/support/servers-unified-computing/ucs-director/products-programming-reference-guides-list.html Regards, Shahzad ... View more

Hello Matthew, 1) Cisco do not do sizing. Cisco create architecture, when a SAP partner, SAP  consultant or SAP provide the requirements in terms of SAPS (the "horsepower" of  a server). 2) Reach out to a Cisco person supporting SAP opportunities in your country. 3) You can locate CISCO partner for your country at following link http://tools.cisco.com/WWChannels/LOCATR/openBasicSearch.do I hope this will help Regards, Shahzad -----Please remember to rate useful posts, by clicking on the stars below------ ... View more

Also Pratyush, 1.How many broadcast domain would be present ? One broadcast doman. 2.In the ARP for the 17.16.16.1/24 will i get any response from 172.16.17.1/24? You can ping both IPs. Multiple domain name can point to single IP in same manner multiple IPs can point to single MAC address, MAC address table is maintained by switch. Regards, Shahzad -----Please remember to rate useful posts, by clicking on the stars below------ ... View more