Hello Darrin, As I mentioned earlier, WAP4410N is a legacy product that has been announced End of Life. There will not be any new feature development for that product. I would suggest you to look at the newer Access Points that offer scheduling capabilities in addition to many other newer features. Please feel free to reach out to our support teams if you have any further questions regarding the Access Points. NT ... View more

Hello Darrin, Thank you for your feedback. Unfortunately, WAP4410N is a legacy product that has been announced End of Life a while ago. We have the Radio Scheduling feature on our newer access points which would function the way you are expecting. Here is an excerpt from our admin guide regarding the scheduler feature: Scheduler The Radio and VAP Scheduler allows you to configure a rule with a specific time interval for VAPs or radios to be operational, which automates the enabling or disabling of the VAPs and radio. Hope this meets your requirements. Regards, NT ... View more

Hello Boris, To check if it is an issue with the switches, could you configure a Layer 3 interface on the SG300 and have it get an IP from the DHCP server? Also, I noticed on the CyberRoam that the interface status for the virtual interface is blank (seems like, per CyberRoam documents, it should show "Connected" with speed/duplex information). Can you please check the CyberRoam to see if the VLAN interface is setup properly? Also, you could try configuring one of the CyberRoam interfaces in the said VLAN, set the corresponding interface on SG300 as an access port, and try to see if that helps? CyberRoam VLAN configuration Document: https://kb.cyberoam.com/default.asp?id=1984 Thanks, Raj ... View more

Hello,   Are you configuring port forwarding to the primary IP of the WAN interface or secondary IP? Would you be able to send me a screenshot of the Port Forwarding page and Access List Page via PM?   Nagaraja ... View more

Hello,   When you create a port forwarding/NAT rule, that just creates the forwarding rule on the router. This rule is telling the router that any traffic hitting the WAN interface of the router on the specific port should be forwarded to the internal server specified. However, it does not dictate who is allowed to access that Service. By configuring the Access Rules to allow only certain internet hosts/networks to access the Service (and your default policy is to block everybody else) you are explicitly telling the Router that only the hosts configured via the access rules are allowed to access the internal server on the configured port and every one else is blocked. As far as the firewall on the Router is concerned, it will block all other traffic initiated from internet destined towards your network but does not have any forwarding rule or explicit allow access rule. In addition, it also protects your network from attacks by inspecting packets going through and allowing only those that belong to an active session (Statefull Packet Inspection).   Hope this helps.   Nagaraja ... View more

Are you referring to Step 3?   Step 3. Enter the IPv6 address of the network that you want to broadcast in IPv6 Address field.   It should be the LAN interface IPv6 address that you want to advertise. This would be the address the clients in the network use to route their IPv6 packets to.   Hope this helps.   Nagaraja ... View more

Hello Michiel,   Can you please check the below links? WAN IPv6 Configuration: http://sbkb.cisco.com/CiscoSB/ukp.aspx?vw=1&docid=255d21a61fbf4843a2a687780bf93e20_Edit_WAN_Connection_on_RV016__RV042__RV042G_and_RV082_VPN_Ro.xml While the above link is related to RV0xx, the UI and configuration tasks are pretty similar to RV320.   DHCPv6 Config on RV320: http://sbkb.cisco.com/CiscoSB/ukp.aspx?vw=1&docid=5d6de1bfe4c1488fb51b75cb76dd0ef6_DHCPv6_Configuration_and_Monitoring_on_RV320_Router.xml&pid=2&respid=0&snid=4&dispid=0&cpage=search   Router Advertisement Configuration: http://sbkb.cisco.com/CiscoSB/ukp.aspx?vw=1&docid=317a760da0c440feb55ec5e12ac21e79_Manage_Router_on_RV320_Router.xml&pid=2&respid=0&snid=4&dispid=0&cpage=search   Hope this helps.   Nagaraja ... View more

Hello Peter,   That is interesting because I am able to put those commands into my SG300 switch and the switch accepts it as entered.     Can you please post the output of the same commands over here?   Nagaraja ... View more

Hello Peter,   Have you tried entering the command without the "ace-priority 1" keyword?   config t mac access-list extended test permit any 00:13:21:b4:ea:2e 00:00:00:00:00:11 exit interface FastEthernet2 description test-device service-acl input test   Nagaraja ... View more

Hello,   Not sure if you had a chance to review the below document:   http://sbkb.cisco.com/CiscoSB/GetArticle.aspx?docid=d6c17b6ee53141f59ae03c6defeb20cb_Dual_WAN_Configuration_on_RV320_Router.xml&pid=2&converted=0#Network_Service_Detection   Nagaraja ... View more

Hello,   Can you please share the page where the configuration gets stuck?   Nagaraja ... View more

Hello,   This issue has been fixed and will be available in our upcoming firmware version. If you would like to verify the fix, please contact our Support Team and open a Service Request. One of our Support Engineers will be happy to work with you and provide you the Beta version of the firmware for testing.   Nagaraja ... View more

Hello Antoinenowak,   The example in the below document may help.   http://sbkb.cisco.com/CiscoSB/ukp.aspx?vw=1&docid=7200e3b590e443af8f27a1ca957705ba_Configuring_a_Site_to_Site_VPN_tunnel_between_RV_Series_Rout.xml&pid=2&respid=0&snid=4&dispid=0&cpage=search   Nagaraja ... View more