Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About anisaini
Stats
Member since
07-07-2011
29
Posts
13
Helpful
5
Solutions
12-09-2013
12:46 PM
Hi Holger, maybe you want to check this out http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a0080b37d0b.shtml http://www.cisco.com/en/US/products/ps5855/products_configuration_example09186a0080a0ece4.shtml
... View more
11-29-2013
11:04 AM
AFAIK there should not be any issues in creating EzVPN or Site to Site VPN provided we have underlying layer 2 and layer 3 correctly configured. what constraints make you feel this is not possible, could you please provid the topology wth devices(hardware and ip addressing)
... View more
07-03-2013
07:25 AM
Hi Raj, It is expected that when you change the username and password on the dialer , it will not be up until you put back the correct username and password. please correct me if your query was something different. Thanks
... View more
07-01-2013
04:09 AM
Hi Fida, Yes you can achieve that logic. This can be done by using a floating static route with the primar having higher preference ip route 0.0.0.0 0.0.0.0 ip route 0.0.0.0 0.0.0.0 200 but only above config might have some loopholes like when the primary is down it will not switch to back-up as the route still exists in routing table. so we need to have some mechanism which will withdraw the first route when there is no traffic passing through primary link, this can be achieved by track feature with ip sla. use "track feature" on 1st static route which will keep track of the primary route and if reachability is lost it will remove the first static route and the next available route will be in routing table. after track config ----------------------------------- ip route 0.0.0.0 0.0.0.0 track 1 track 1 ip sla 1 ip sla 1 icmp-echo 4.2.2.2 source-interface ip sla schedule 1 life forever start-time now ip route 4.2.2.2 255.255.255.255 permanent ip route 0.0.0.0 0.0.0.0 200 i found another good link which explains the same https://supportforums.cisco.com/docs/DOC-6078 Hope this helps.
... View more
07-01-2013
03:42 AM
Hi Jonathan, you have bgp peer on gig interface, which should not be genrally causing any bottleneck, to troubleshoot this further i would perform following task to further isolate the issue. 1. check if the CPU is highly ustilised when the telco reports any missing keepalive, when cpu is high i may missout to process the control packets even if its high priority 2. control plane traffic is by default prioritized over the data traffic either by pak_priority or ip precedence 3. also it will be great to have wireshark capture on this gig interface which will prove the point that if bgp keepalive are sent out, this will be thw proving point hope this helps Thanks
... View more
07-01-2013
01:06 AM
Hope you have gone through the link below http://www.cisco.com/en/US/docs/routers/access/interfaces/software/feature/guide/shdslfm.html#wp1090715 check if the controller is up or down check if controller is up and if issuw with higher layer protocol Thanks
... View more
06-30-2013
08:35 AM
Hi Sudan, Can you please attach following output 1."show tech" 2. show dsl int atm x 3. sh controller atm/dsl 4. was it working fine before after having a look in more specifics we can narrow down the issue Thanks
... View more
05-12-2013
12:31 AM
first you can try to upgrade to the latest firmware(find it under cisco877 firmware in cisco website software download) http://software.cisco.com/download/release.html?mdfid=279624018&softwareid=282821763&release=0.0.026 then also if you have any issues you need to check with TELCO for bad line
... View more
05-11-2013
11:49 PM
Hi Pranav, Please share the following config debug ip dhcp server packet debug ip dhcp server event check if the server is sending/replying the client broadcast/packets then try to connect the pc directly to check if layer2 switch is causing the issue you may also take wireshark captures on the PC to check what is being send and received in terms of DHCP. hope this helps
... View more
05-07-2013
09:14 AM
Hi Danny, if you want to connect two 887(presumably in distant geographies) using L2tp then you need to have a layer 3 connectivity between LAC and LNS where the l2tp tunnels will be formed. you may want to explore L2 Mpls . Thanks
... View more
03-31-2013
09:34 PM
check using trace which hop is causing delay also ensure that the path taken by these two routes(source) is same
... View more
03-31-2013
09:19 AM
Yes thi can be done but you need to take in consideration if these two links are provided by same provider and any timings issues(at link or conroller level) is not present else there will be to many fragments loss and hence too many dropped packets.
... View more
03-31-2013
09:15 AM
Information regarding the platform missing, You can try the below steps to further isolate/fix the issue. 1. modify the acl matching route-map as it has match any any, so just match the specific tarffic of your interest 2. ensure that the traffic of interest hist the interface where PBR is applied 3. some platform will not show the ACL hits in route-map of PBR as this will be fast switched and no cpu processed 4. ensure that you have the correct SDM template enable, like routing or application(for ME switches) 5. check if the device to which you are sending these packets to has reverse route so that the routing path is not broken 6. to ensure that the packets are hitting PBR or if PBR is working, enable the debug ip policy and this will gibe you the clear picture and you can proceed accordingly. Most likely issues are covered above and hence shd be resolving the issue, if still not working provide follwing 1. debug ip policy 2. wireshark cap on exit interface of this witch reply if this helps
... View more
03-25-2013
11:02 AM
check your config/hardware "controller VDSL 0/1/0" its a VDSL and not ADSL, for the option that you are looking for are available depending on the card , some cards are VA which has VDSL as well as ADSL some are just V(ie VDSL) Hence check what your current hardwar is or what you are looking for. http://www.cisco.com/en/US/docs/routers/access/interfaces/software/feature/guide/vdsl2_hwic.pdf
... View more
12-09-2013
Hi Holger,maybe you want to check this
outhttp://www.cisco.com/en/US/products/ps6120/products_config...
11-29-2013
AFAIK there should not be any issues in creating EzVPN or Site to Site
VPN provided we have underlyi...
07-01-2013
Hi Jonathan,you have bgp peer on gig interface, which should not be
genrally causing any bottleneck,...
07-01-2013
Hope you have gone through the link
belowhttp://www.cisco.com/en/US/docs/routers/access/interfaces/s...
06-30-2013
Hi Sudan,Can you please attach following output 1."show tech"2. show dsl
int atm x3. sh controller a...
05-12-2013
first you can try to upgrade to the latest firmware(find it under
cisco877 firmware in cisco website...
05-11-2013
Hi Pranav,Please share the followingconfig debug ip dhcp server
packetdebug ip dhcp server eventchec...
05-07-2013
Hi Danny,if you want to connect two 887(presumably in distant
geographies) using L2tp then you need ...
03-31-2013
check using trace which hop is causing delayalso ensure that the path
taken by these two routes(sour...
03-31-2013
Yes thi can be done but you need to take in consideration if these two
links are provided by same pr...
03-31-2013
Information regarding the platform missing, You can try the below steps
to further isolate/fix the i...
Public Statistics
| Date Registered | 07-07-2011 11:04 AM |
| Date Last Visited | 08-18-2017 04:03 AM |
| Total Messages Posted | 29 |
| Total Helpful Votes Received | 13 |
